Heatmor 100 CSS User manual

Outdoor Furnaces
TM
SAVE THESE INSTRUCTIONS

ii
When these safety symbols appear on the following pages, they will
alert you to the possibility of serious injury if you do not comply with the
corresponding instructions. The hazard may originate from something
mechanical or electrical shock. Please read the instructions carefully.
When you see this safety symbol on the following pages, it will alert you
to the possibility of damage to your HEATMORTM Stainless Steel Outdoor
Furnace if you do not comply with the corresponding instructions. Please
read the instructions carefully.
The HEATMORTM Stainless Steel Outdoor Furnace is certied to offer safe
service provided it is installed, operated and maintained in accordance with
the instructions contained in this manual.
Proper personal protective equipment, (PPE), MUST BE WORN AT ALL
TIMES when servicing and maintaining any of the HEATMORTM Stainless
Steel Outdoor Furnace product line.

iii
TABLE OF CONTENTS Page #
I DEAR HEATMOR™ OWNER 1
II NOTICE TO THE READER 2
III CERTIFICATE OF COMPLIANCE 3,4
1 HEATMOR™ STAINLESS STEEL FURNACE MODELS 5
2 FURNACE SPECIFICATIONS 6
3 FRONT CUT AWAY VIEW OF HEATMOR™ OUTDOOR FURNACE 7
FURNACE PARTS LIST 8
4 REAR CUT AWAY VIEW OF HEATMOR™ OUTDOOR FURNACE 9
FURNACE PARTS LIST 10
5 MINIMUM CLEARANCE SEPARATION SPECIFICATIONS 11
6 WARNINGS AND PRECAUTIONS 12
A Installation 12
B Electrical 13
C Other 13
7 CONCRETE PAD SPECIFICATIONS 14-16
8 INSTALLATION OF THE HEATMOR™ FURNACE 17
A Equipment Required 17
B Placing the HEATMOR™ on the Concrete Pad 17
C Caulking Around the Firebox Base 17
D Caulking Around the Outside Perimeter of HEATMOR™ 17
E Filling the HEATMOR™ Outdoor Furnace Initially with Water 18
F Maintaining Water in the Bladder and in the HEATMOR™ 19
G Initial Installation of Sand 20
i. Types of sand to use 20
ii. Installation 20
9 SAFE OPERATING GUIDELINES 21
A Operation 21
B Lighting Your HEATMOR™ for the First Time 23
C Dew Point 24
D Loading Wood into the HEATMOR™ 25
E What can I burn? 26
i. Wood 26
F How does a fire burn out? 26
G Types of Wood 27
H Wood as a Fuel 27
I Stages of Combustion 27
J Efficiency Measurements and Types of Fires 28
K Types of Fires 28
L Handling and Storage of Wood 29
M Types of Coal 30
N Coal as a Fuel 30

iv
O Handling and Storage of Coal 30
P Loading Coal into the HEATMOR™ 30
10 WATER 31
A Qualities of Water to Use 31
B Water Level Maintenance 31
C Removal of water and replacement of water 31
D Water Additives 32
E Water Treatment Additives and Safety Specifications 33
F Adding Water Treatment and Freeze Protection Products 34
11 BLADDER ASSEMBLY 36
A Bladder 36
B Bladder Gate Valve and Bladder Hose 37
C Water Level Gauge 38
D Bladder Cover Plate 38
12 WATER JACKET 39
A Water Jacket 39
B Supply Line and Return Line Connectors 39
C Relief Vent Pipe and Weighted Pop off Ball 39
13 FIREBOX AND OTHER COMPONENTS 40
A Firebox 40
B Firebox Door 41
C Firebox Door Hoses and Elbows 43
D Firebox Door Handle 44
E Firebox Door Hinge 44
F Firebox Door Latch 44
G Firebox Door Holder 45
H Firebox Door Gasket 45
I Firebox Door Frame 46
J Firebox / Base Connector Clamps 46
K Firebrick 47
L Standard Grates 47
M Optional Shaker Grates 48
N Sand 49
i. Types of sand to use 49
ii. Installation 49
O Flash Curtain / Heat Shield 50
14 AIR SUPPLY 51
A Combustion Air Blower and Flipper Assembly 51
i. Operation of the Combustion Air Blower and Flipper Assembly 51
ii. Steps to Maintain your Blower / Flipper Assembly 51
B Air Box(s) 52
C Combustion Air Percentage Tube 53
D Automatic Fan Switch (A.F.S.) 53

v
15 CHIMNEY AND TOP FLUE 54
A Chimney 54
B Chimney Extension(s) 54
C Flue 55
D Top Flue Cover 55
E Flue Scraper 55
16 ASHES 56
A Ash Management and Ash Removal 56
B Ash Pan 57
C Ash Auger 57
D Ash Auger Tube 57
E Ash Auger Tube Cover Plate 58
17 THERMOMETER (TEMPERATURE GAUGE) 59
18 ELECTRICAL 60
A Electrical Supply 60
B Electrical Supply Junction Box 60
C Double Electrical Outlets at rear 61
D Water Temperature Range Control (Aquastat on the left) 61
E High Water Temperature Safety Shutoff Controller (Aquastat on the right) 62
F Front Light and Fan Power Switch 63
G In The Event of a Power Failure 64
19 EXTERIOR CLADDING AND INSULATION 65
A Outer Door of HEATMOR™ 65
B Roof of the HEATMOR™ 65
C Sides of the HEATMOR™ 66
D Insulation 66
20 AIR LEAKS 67
A Checking For Air Leaks 67
B Why do we not want any air leaks? 67
21 WATER LEAKS 68
22 DOMESTIC COIL 69
23 SEASON START UP & SHUT DOWN CHECKLISTS 70
24 FREQUENTLY ASKED QUESTIONS 73
25 TROUBLESHOOTING AND SOLUTIONS 75
HEATMOR™ STAINLESS STEEL LIMITED WARRANTY 88
HEATMOR™ FOR LIFE 91
NOTES 92

1
Dear HEATMOR™Owner,
On behalf of myself and the employees of HEATMOR™, I would like to take this opportunity to personally
thank you for the purchase of our HEATMOR™ Stainless Steel Outdoor Furnace. You can be assured that
your HEATMOR™ was constructed with great emphasis on quality and workmanship. It is our commitment to
provide you with the finest outdoor furnace in the industry. We wish you many years of trouble-free use and we
sincerely hope you enjoy the comforts of burning wood.
This manual contains the manufacturer’s recommendations for operation and maintenance of the HEATMOR™
Stainless Steel Outdoor Furnace. Also included are some regular maintenance tips and FAQ’s (frequently
asked questions). Please observe and follow all safety instructions as directed in this manual. SAVE THESE
INSTRUCTIONS FOR FUTURE REFERENCE.
Finally, please fill out your registration and warranty forms, if you haven’t done so already. If you have any
further questions on the operation or maintenance of your HEATMOR™ Outdoor Furnace, please contact your
local dealer.
Sincerely,
Gerry Reed,
President

2
NOTICE TO THE READER
HEATMOR™ Inc. warrants and guarantees ALL HEATMOR™ Stainless Steel Outdoor Furnace Models.
HEATMOR™ Inc. does not warrant or guarantee any of the supporting products described within this
Operations and Maintenance Manual.
The contents, descriptions, directions, diagrams, and recommendations within this material are for the sole
purpose of suggested operation and maintenance methods.
Furthermore, HEATMOR™ Inc. shall not be liable for any special, consequential, or exemplary damages,
resulting, in whole or part, from the readers’ neglectful use, based upon the material within this Operations and
Maintenance Manual. Adhere to and follow all maintenance procedures set forth in this manual.
The methods of operation described within this Operations and Maintenance Manual have proven to be
effective for HEATMOR™ Inc. for the sole purpose of the operation of a HEATMOR™ Stainless Steel Outdoor
Furnace.
All formulas and gures listed within this Operations and Maintenance Manual are approximated and should be
read as such.
For additional copies or information, contact
HEATMOR™ Inc.
105 Industrial Park Court NE,
P.O. Box 787,
Warroad, MN 56763 USA
Phone: [phone]
Fax: [phone]
Website: www.heatmor.com
E-mail: [e-mail]
Copyright © 2012- HEATMOR™ INC.
All rights reserved. No part of this Operations and Maintenance Manual may be reproduced or used in any
form or by any means - graphic, electronic or mechanical, including photocopying, recording, taping, or
information storage and retrieval systems - without the written permission of HEATMOR™ Inc.
MODELS (100 CSS, 200 CSS, 400 DCSS)
Supplemental literature will be provided in addition to this manual for Models 200 CSS/OB, 400 DCSS/OB, 600
CSS and 800 CSS.

3
Units are Safety Listed by Omni Test Laboratories
Report # 275-O-11-4 and # 275-O-12-4
Listed to UL2523-2009 and CSA B366.1-11

4
Units are Safety Listed by Omni Test Laboratories
Report # 275-O-11-4 and # 275-O-12-4
Listed to UL2523-2009 and CSA B366.1-11

5
HEATMOR™ STAINLESS STEEL OUTDOOR FURNACE MODELS
Model 100 CSS Model 200 CSS
Model 400 DCSS
CHAPTER 1

6
RESIDENTIAL FURNACE SPECIFICATIONS
Specications Model 100 CSS Model 200 CSS Model 400 DCSS
Overall Width (Inches)
Base Width (Inches) (Footprint)
50
46.5
50
46.5
50
46.5
Overall Height (Inches)
(With chimney stub) 82.5 82.5 82.5
Overall Length (Inches)
Base Length (Inches) (Footprint)
65
53.75
77
65.75
95
83.75
Total Weight (lbs., without water) 1375 1599 1968
Water Capacity (U.S. gallons) 85 114 155
Forced Draft (C.F.M.) 75 150 2 x 150 = 300
Chimney Size (Inches) 8 8 8
Wood Length (Inches) 24 36 54
Insulated Heating Area (Sq. Ft.)*
1 Loading/day
2 Loading/day
1500
3000
2500
5000
5000
10,000
Firebox Width (Inches) 28 28 28
Firebox Length (Inches) 24 36 54
Firebox Height (Inches) 42 42 42
Volume of Firebox (Cu. Ft.) 14 21 32
Firebox Door Size (Inches) (W x H) 20 x 18 20 x 18 20 x 18
Flue Transfer Area (Sq. Ft.) 6.5 10 15
BTU’s (maximum)** 100,000 200,000 400,000
Water Jacket Steel
Gauge
409 Stainless
10
409 Stainless
10
409 Stainless
10
Firebox Steel
Gauge
409 Stainless
10
409 Stainless
10
409 Stainless
10
Base Steel
Gauge
409 Stainless
14
409 Stainless
14
409 Stainless
14
Base of Unit to
Bottom of Loading Door (Inches) 24 24 24
Warranty - Workmanship Limited Lifetime Limited Lifetime Limited Lifetime
Warranty - Corrosion Limited Lifetime Limited Lifetime Limited Lifetime
Approvals Test Standards UL Subject 2523 UL Subject 2523 UL Subject 2523
Hook-ups Back Back Back
Total Heat Extraction Area (Sq. Ft.) 30.89 40.89 55.89
Type of Fuel Wood and Coal Only Wood and Coal Only Wood and Coal Only
Electrical Supply 115 V, 60HZ, 1 Phase 115 V, 60HZ, 1 Phase 115 V, 60HZ, 1 Phase
CHAPTER 2
* This is an estimate only. Actual loadings per day may vary depending on structures heated and type of wood used.
** This value should only be used as an indication of the furnace’s heat recovery ability. Sustained outputs at this rate will increase the
loadings per day. Some types of wood may prevent the furnace from reaching this maximum output.

7
CHAPTER 3
FRONT CUT-AWAY VIEW OF HEATMOR™ OUTDOOR FURNACE
(For parts not shown on the cut-away view, please refer to the appropriate chapter for further details.)

8
FURNACE PARTS LIST
Firebox
1) Firebox
2) Firebox door
3) Firebox door hoses and elbows
4) Firebox door handle
5) Firebox door hinge
6) Firebox door latch
7) Firebox door handle holder(not shown)
8) Firebox door gasket
9) Firebox door frame
10) Firebox / base connector clamps
11) Firebrick
12) Standard grates
13) Optional shaker grates(not shown)
14) Sand(not shown)
15) Flash curtain / heat shield(next page)
Water jacket
16) Water jacket (surrounds rebox)
18) Supply line threaded connector(next page)
19) Return line threaded connector(next page)
20) Relief vent pipe
21) Weighted pop off valve
Air supply
22) Combustion air blower (400 DCSS - 2 Fans)
23) Flipper assembly
24) Air box(s)(next page)
25) Combustion air percentage tube(next page)
26) Automatic Fan Switch (A.F.S.)
Chimney and top flue
27) Chimney Stub
28) Chimney extension(s)(not shown)
29) Top rectangular ue(next page)
30) Top ue cover plate(next page)
31) Top ue scraper(not shown)
Ashes
32) Ash pan
33) Ash auger(not shown)
34) Ash auger tube(next page)
35) Ash auger tube cover plate(next page)
Bladder assembly
36) Bladder
37) Bladder gate valve and hose
38) Water level gauge
39) Bladder inspection cover plate
Thermometer
40) Thermometer
Electrical
41) Electrical supply junction box(next page)
42) Electrical plug outlets(next page)
43) Water temperature controller
(aquastat) (next page)
44) Water temperature high-limit
controller (aquastat) (next page)
45) Front light and combustion air
blower control switch
Housing
46) Outer front door(not shown)
47) Outer rear door(not shown)
48) Roof
49) Sides(not shown)
50) Insulation(not shown)
Optional hot water internal coil
51) Internal coil(not shown)
Lift hook
52) Lift ring
53) Box of Chemical, Keys, Manual

9
CHAPTER 4
REAR CUT-AWAY VIEW OF HEATMOR™ OUTDOOR FURNACE
(For parts not shown on the cut-away view, please refer to the appropriate chapter for further details.)

10
FURNACE PARTS LIST
Firebox
1) Firebox
2) Firebox door
3) Firebox door hoses and elbows
4) Firebox door handle
5) Firebox door hinge
6) Firebox door latch
7) Firebox door handle holder(not shown)
8) Firebox door gasket
9) Firebox door frame
10) Firebox / base connector clamps
11) Firebrick
12) Standard grates
13) Optional shaker grates(not shown)
14) Sand(not shown)
15) Flash curtain / heat shield
Water jacket
16) Water jacket (surrounds rebox)
18) Supply line threaded connector
19) Return line threaded connector
20) Relief vent pipe
21) Weighted pop off valve
Air supply
22) Combustion air blower (400 DCSS - 2 Fans)
23) Flipper assembly
24) Air box(s)
25) Combustion air percentage tube
26) Automatic Fan Switch (A.F.S.)
Chimney and top flue
27) Chimney Stub
28) Chimney extension(s)(not shown)
29) Top rectangular ue
30) Top ue cover plate
31) Top ue scraper(not shown)
Ashes
32) Ash pan
33) Ash auger(not shown)
34) Ash auger tube
35) Ash auger tube cover plate
Bladder assembly
36) Bladder
37) Bladder gate valve and hose
38) Water level gauge
39) Bladder inspection cover plate
Thermometer
40) Thermometer
Electrical
41) Electrical supply junction box
42) Electrical plug outlets
43) Water temperature controller
(aquastat)
44) Water temperature high-limit
controller (aquastat)
45) Front light and combustion air
blower control switch
Housing
46) Outer front door(not shown)
47) Outer rear door(not shown)
48) Roof
49) Sides(not shown)
50) Insulation(not shown)
Optional hot water internal coil
51) Internal coil(not shown)
Lift hook
52) Lift ring
53) Box of Chemical, Keys, Manual

11
11
MINIMUM CLEARANCE SEPARATION SPECIFICATIONS
The HEATMOR™ furnace, is certified to be installed outside, away from other buildings. Please observe the
following “Clearance to Combustibles” guidelines. If you have any further questions, which are not addressed
in this Operators Manual, please contact your local dealer for further information.
♦ To HEATMOR™ Stainless Steel Outdoor Furnace Back. 96 Inches
♦ To HEATMOR™ Stainless Steel Outdoor Furnace Top. 18 Inches
♦ To HEATMOR™ Stainless Steel Outdoor Furnace Front. 48 Inches
♦ To HEATMOR™ Stainless Steel Outdoor Furnace Chimney. 96 Inches
♦ To HEATMOR™ Stainless Steel Outdoor Furnace Sides. 6 Inches
♦ Do not store combustible liquids or materials near the furnace.
♦ It is not recommended to install the furnace in any form of building.
Before installing your HEATMOR™ Stainless Steel Outdoor Furnace, if in the United States, always check
any and all applicable state and local regulations and inform your insurance agent.
Before installing your HEATMOR™ Stainless Steel Outdoor Furnace, if in Canada, always check any and all
applicable Provincial and Municipal regulations and inform your insurance agent.
HEATMOR™ Inc. strongly recommends not installing a HEATMOR™ Stainless Steel Outdoor Furnace within
50 feet of any flammable structure.
A HEATMOR™ Stainless Steel Outdoor Furnace should be located with consideration to your neighbor’s
property and in accordance with local ordinances. Refer to the “Best Burn Practices” for further operating
considerations.
HEATMOR™ Outdoor Furnaces, Model 100 CSS, 200 CSS and 400 DCSS are not designed or certified to be
located in densely populated areas.
CHAPTER 5

12
CHAPTER 6
WARNINGS AND PRECAUTIONS
Please read the following list of cautions, warnings and dangers before installing and operating
your HEATMOR™ STAINLESS STEEL OUTDOOR FURNACE. If you have any questions or concerns
regarding any of the following cautions, warnings, dangers or instructions in this Operations and
Maintenance manual, please contact your local dealer.
Familiarize yourself with the “Best Burn Practices” located on the inside front cover.
Installation
If you are installing parts of this heating system on a “do-it-yourself” basis, it is highly recommended
that you purchase a total system installation manual recommended by your dealer.
1) The HEATMOR™ furnace is designed for outside installations, away from other buildings.
2) Please observe the following “ Clearance to Combustibles “ guidelines.
To unit back = 96 inches To unit sides = 6 inches
To unit front = 48 inches To chimney = 96 inches
3) Before installing the furnace, always check any and all applicable state, provincial, and local
regulations.
4) HEATMOR™ Inc. strongly recommends not installing a HEATMOR™ Stainless Steel Outdoor
Furnace within 50 feet of any ammable structure.
5) A HEATMOR™ Stainless Steel Outdoor Furnace should be located with consideration
to your neighbor’s property and in accordance with local ordinances. HEATMOR™ Outdoor
Furnaces, Model 100 CSS, 200 CSS and Model 400 DCSS, are not designed to be located
in densely populated areas.
6) HEATMOR™ suggests the use of brass ttings when installing the unit.
7) Before installing the HEATMOR™ furnace, contact and inform your insurance agent.
8) The HEATMOR™ Outdoor Furnace is to be installed on a concrete base only. Any attempt to place
the furnace on any other surface may void the warranty.
9) Do not connect the HEATMOR™ furnace to the chimney of any existing heating system.
10) This unit was not designed, nor is it recommended, for use as a stand-alone heating system. A back
up source of heat must be in place to prevent the outdoor furnace from freezing and to provide
supplementary heat for the heated buildings.
11) Do not pressurize the HEATMOR™ Outdoor Furnace. This unit is designed to operate under
atmospheric pressure only.
12) Place the in-line ll/drain assembly in a location where the drained contents of the HEATMOR™ will
not cause damage to the surrounding areas or it’s contents.
12
WARNINGS AND PRECAUTIONS
Please read the following list of cautions, warnings and dangers before installing and operating
your HEATMOR™ STAINLESS STEEL OUTDOOR FURNACE. If you have any questions or concerns
regarding any of the following cautions, warnings, dangers or instructions in this Operations and
Maintenance manual, please contact your local dealer.
Familiarize yourself with the “Best Burn Practices” located on the inside front cover.
Installation
If you are installing parts of this heating system on a “do-it-yourself” basis, it is highly recommended
that you purchase a total system installation manual recommended by your dealer.
1) The HEATMOR™ furnace is designed for outside installations, away from other buildings.
2) Please observe the following “ Clearance to Combustibles “ guidelines.
To unit back = 96 inches To unit sides = 6 inches
To unit front = 48 inches To chimney = 96 inches
To unit top = 18 inches
3) Before installing the furnace, always check any and all applicable state, provincial, and local
regulations.
4) HEATMOR™ Inc. strongly recommends not installing a HEATMOR™ Stainless Steel Outdoor
Furnace within 50 feet of any flammable structure.
5) A HEATMOR™ Stainless Steel Outdoor Furnace should be located with consideration
to your neighbor’s property and in accordance with local ordinances. HEATMOR™ Outdoor
Furnaces, Model 100 CSS, 200 CSS and Model 400 DCSS, are not designed to be located
in densely populated areas.
6) HEATMOR™ suggests the use of brass fittings when installing the unit.
7) Before installing the HEATMOR™ furnace, contact and inform your insurance agent.
8) The HEATMOR™ Outdoor Furnace is to be installed on a concrete base only. Any attempt to place
the furnace on any other surface may void the warranty.
9) Do not connect the HEATMOR™ furnace to the chimney of any existing heating system.
10) This unit was not designed, nor is it recommended, for use as a stand-alone heating system. A back
up source of heat must be in place to prevent the outdoor furnace from freezing and to provide
supplementary heat for the heated buildings.
11) Do not pressurize the HEATMOR™ Outdoor Furnace. This unit is designed to operate under
atmospheric pressure only.
12) Place the in-line fill/drain assembly in a location where the drained contents of the HEATMOR™ will
not cause damage to the surrounding areas or it’s contents.
CHAPTER 6
Installation should be performed by a qualied installer and will comply with all the requirements of
the authority having jurisdiction over the installation.

13
CHAPTER 6
Electrical
1) Do not connect the electrical components of the HEATMOR™ Outdoor Furnace to any other
electrical appliance.
2) This HEATMOR™ Outdoor Furnace operates on 115-volt power only. Do not connect the furnace to a 220-
volt electrical supply.
3) HEATMOR™ INC. recommends a licensed professional electrician make all the necessary
electrical connections involved with the installation of the furnace.
4) Always disconnect the HEATMOR™ Outdoor Furnace from the main electrical supply before
servicing any of the electrical components of the HEATMOR™ Outdoor Furnace.
5) Always disconnect any existing electrical connections to any in-house heating system, before
installing the outdoor furnace to any existing indoor heating system or appliances.
6) The red wire from the high-limit aquastat on the back of the HEATMOR™ should be wired to the
indoor temperature control to override the thermostat. This will dissipate excess heat in the event of a
possible malfunction with the HEATMOR™. (The red wire is capped off in the electrical junction
box when the HEATMOR™ is new.)
Other
1) The unit may be connected to an existing indoor boiler system by installing a water-to-water heat
exchanger.
1) HEATMOR™ INC. recommends that you contact a licensed professional plumber to make
all necessary plumbing installations between the HEATMOR™ furnace and the existing heating
system of your building(s).
2) Do not operate the HEATMOR™ furnace until all electrical and water line connections have
been properly installed and tested.
3) Do not allow any re in the rebox until the HEATMOR™ has the correct amount of water and
sand installed.

14
CHAPTER 7A
4”
BASE: OUTDOOR FURNACE SITS ON THIS PAD
50”
58”
26”
12”
10”
PATIO STONES OR SEPARATE CEMENT SLAB
FOR CONVENIENT LOADING
48”
OUTDOOR FURNACE SITS HERE
ASH AUGER
LOADING AREA
GROUND
LEVEL
FOUR INCH GRAVEL BASE
CEMENT BASE
UNDERGROUND LINES
MODEL 100 PAD SPECIFICATIONS
The actual pad size is 50” x 58”. This gives
approximately 2” extra on all sides of furnace.
CAUTION: Do not exceed this length measurement.
Width can be wider if desired.
The bottom of the loading door is 24” above ground
or base of furnace. If you desire to have the leading
door higher, you can do so by making the pad depth
thicker.
Example: 12” instead of 4” or any gure in between.
Patio stones or separate cement pad in front of the
loading door should NOT be attached to main base
of furnace.
It is recommended to use steel mesh or R-bar
in pad for strength.
Benefits to raising the pad:
1. Gives space below the ash auger to place a pail
for convenient ash removal.
2. Allows better visibility of the rebox.
3. Less bending when adding wood.
4. Keeps smoke above the operator.
5. Protects the base of the HEATMOR™.
PATIO STONES OR
SEPARATE CEMENT SLAB.
CEMENT BASE 4” - 12”
HIGHER THAN WHERE THE
OPERATOR STANDS.
LOADING
DOOR
SIDE VIEW
HOLES FOR HOOK-UPS
6”
AUGER

15
CHAPTER 7B
4”
BASE: OUTDOOR FURNACE SITS ON THIS PAD
70”
26”
12”
10”
PATIO STONES OR SEPARATE CEMENT SLAB
FOR CONVENIENT LOADING
48”
OUTDOOR FURNACE SITS HERE
ASH AUGER
LOADING AREA
GROUND
LEVEL
FOUR INCH GRAVEL BASE
CEMENT BASE
UNDERGROUND LINES
MODEL 200 PAD SPECIFICATIONS
The actual pad size is 50” x 70”. This gives
approximately 2” extra on all sides of furnace.
CAUTION: Do not exceed this length measurement.
Width can be wider if desired.
The bottom of the loading door is 24” above ground
or base of furnace. If you desire to have the leading
door higher, you can do so by making the pad depth
thicker.
Example: 12” instead of 4” or any gure in between.
Patio stones or separate cement pad in front of the
loading door should NOT be attached to main base
of furnace.
It is recommended to use steel mesh or R-bar
in pad for strength.
Benefits to raising the pad:
1. Gives space below the ash auger to place a pail
for convenient ash removal.
2. Allows better visibility of the rebox.
3. Less bending when adding wood.
4. Keeps smoke above the operator.
5. Protects the base of the HEATMOR™.
PATIO STONES OR
SEPARATE CEMENT SLAB.
CEMENT BASE 4” - 12”
HIGHER THAN WHERE THE
OPERATOR STANDS.
LOADING
DOOR
50”
SIDE VIEW
HOLES FOR HOOK-UPS
6”
AUGER