HEATSTRIP THAC-100 User manual

Product & Assembly
Manual
HEATSTRIP® Portable Stand
(English)

2
For repairs or replacement parts, please contact:
Thermofilm Australia Pty Ltd
17 Johnston Court, Dandenong South, Victoria 3175, Australia
Telephone: [phone]
8:30am-5:00pm Mon-Fri (EST)
Email: [e-mail]
To obtain the correct replacement parts for your electric radiant heater, please refer to
the part numbers in this parts list. The following information is required to ensure you
receive the correct parts:
1. Model and Serial Number (see label on the heater)
2. Part Number
3. Part Description
4. Quantity of parts needed
Important: Use only Thermofilm replacement parts. The use of any part that is not a
Thermofilm replacement part can be dangerous and void your product warranty. Keep
this Instruction Manual for convenient referral and for parts replacement.
Contents
Product Overview 3
Specifications 3
Product Features & Benefits 3
Installation Requirements 4
Parts List 4
Product Parts Diagram 5
Hardware Pack & Tools Required 6
Assembly Instructions 7
Electric Heater Assembly Instructions 7-9
Maintenance and Safety 10
Replacement Parts 10
Warranty 11
Dutch ___________________________________________________________________-13
French__________________________________________________________________________-25
German_________________________________________________________________________-37
Manual # Rev A - Date:23/11/2018

3
Specifications - Europe
MODEL DIMENSIONS (mm) WEIGHT (Kg)
THAC-100 1068(W) x 2050(H) x 500(D) 15
HEATER TYPE SUITABLE Design, Elegance, Intense, Max
APPROVALS AUSTRALIA/NZ/CE
PROTECTION RATING IPX5 Protection from water ingress from all directions
MATERIAL OF CONTRUCTION Stand: Powder coated mild steel
Features & Benefits
• Stylish, high quality portable, free-standing outdoor heat-
er stand
• Ideal for alfresco areas, balconies, apartments & hospi-
tality (internal & external use)
• Concealed power cable ensures a sleek appearance
• Components are sub-assembled for easy DIY installation
• In-built wheels for easy portability, perfect for residential
and commercial applications
• Corrosion protected for even the toughest environments
• 2 year residential and 1 year commercial warranty
Tips
• If an extension lead is required, use one as short as pos-
sible, as a long lead may result in performance loss
• Locate the heater as close to the power point as possible
• This portable heater is for spot heating only. Locate as
close to the area you want to heat as possible (e.g Ta-
ble)
• Store under cover at all times

4
Parts List of THAC-100
Key Description QTY
Wheel
Skid Pad
Base
Kick Plate
Fixed Bracket
Post - Rear, Lower
Post - Rear, Upper
Post - Front, Lower
Post - Front, Upper
10 Side Panel / Left
11 Side Panel / Right
12 Rear Panel
13 Heater Bracket
14 Base Bracket
NOTE: Example Image

5
Parts Diagram
Key Description
1Wheel
2Skid Pad
3Base
4Kick Plate
5Fixed Bracket
6Post—Rear, Lower
7Post—Rear, Upper
8Post—Front, Lower
9Post—Front, Upper
10 Side Panel / Left
11 Side Panel / Right
12 Rear Panel
13 Heater Bracket
14 Base Bracket
13
10

6
Pan Head Screw M6x10mm
QTY: 39
Hardware Diagram for THAC-100
PART DESCRIPTION QTY PURPOSE OF PART
Hardware Pack For use in assembly of stand
Pan Head Screw M6 x 10mm 5Connecting Base
Pan Head Screw M6 x 10mm Install Base Brackets to Base
Pan Head Screw M6 x 10mm Install Lower Post to Base
Pan Head Screw M6 x 10mm
Install Side Panels to Lower Post & Base
Pan Head Screw M6 x 10mm
Pan Head Screw M6 x 10mm
Install Real panel to Side Panel & Lower Post
Pan Head Screw M6 x 10mm
Pan Head Screw M6 x 10mm Install Heater Bracket to Upper Post
Pan Head Screw M6 x 10mm Install Upper Post to Lower Post
Screwdriver
Pan Head Screw M6 x 10mm Install Lower Post to Base
Hardware Pack For THAC-100
Phillips Head Screwdriver
Flange Nut M6
QTY: 15
Hexagon Nut M12
QTY: 2

7
Assembly Instructions
CAUTION: To assemble this heater, you should obtain assistance from another person when handling the
larger, heavier pieces.
1
Install Base Brackets
• Remove all the packing material and place on a non-abrasive
surface.
• Position the Base as shown in the diagram.
• Once the slotted holes are aligned, use 5 Pan Head screws
then tighten securely with the nuts provided
• Install two Brackets to the Base using 4 Pan Head Screws
(M6x10mm), once brackets are in place tighten all the screws
securely.
• Adjustable Skid Pads will be provided. Screw Skid Pads on
each corner as shown in the diagram.
Note: Base brackets can be concealed if angled inwards.
• Attach the Lower Post to the Base by matching the
slotted holes on the Lower Post into the screws on
the Base. Next, attach 3 Pan Head Screws
M6x10mm, then tighten all the screws securely
Install Lower Post
Joining Base
2
3
Pan Head Screw M6x 10mm
QTY: 4
Pan Head Screw M6x 10mm
QTY: 3
Flange Nut M6
QTY: 5
Pan Head Screw M6x 10mm
QTY: 5

8
Assembly Instructions
CAUTION: To assemble this heater, you should obtain assistance from another person when handling the
larger, heavier pieces.
• Place two Side Panels onto the Base.
• Install the Left Side Panel to the Lower Post using 2 Pan
Head Screws (M6x10mm). Then place the Left Side Panel to
the Base matching the slotted holes. Once the slotted holes
are matching, use 3 Pan Head Screws (M6x10mm) and
screw securely with the Flange Nuts.
• Repeat the same procedure for the Right Side Panel, then
tighten all the screws securely.
Install Side Panels
4
• Place and install the Rear Panel to the Lower Post using
2 Pan Head screws. (M6x10mm)
• Once the top 2 Pan Head screws are Installed, match the
slotted holes on the Rear Panel to the Side Panels.
Screws all 4 holes securely using 4 pan head screws
(M6x10mm) and Flange Nuts.
• Place the bracket head on the top post.
• Using the Bracket Head, match the slotted holes to the top post.
Once the slotted holes are matched, use 4 pan head screws
(M6x10mm), then tighten securely shown in the diagram.
• Ensure bracket is attached in the correct direction, as per the
diagram.
Install Rear Panel
Install Heater Bracket to the Top Post
5
6
Pan Head Screw M6x10mm
QTY: 6
Pan Head Screw M6x10mm
QTY: 10
Pan Head Screw M6x10mm
QTY: 4
Flange Nut M6
QTY: 6
Flange Nut M6
QTY: 4

9
Assembly Instructions
CAUTION: To assemble this heater, you should obtain assistance from another person when handling the
larger, heavier pieces.
7Install Top Post to the Lower Post
Install the Heater to Bracket Head attached on the Upper Post
• Insert and slide the top post over to the lower post connecting
the stand using 8 pan head screws (M6x10mm), then tighten all
screws securely.
• Using the 2 brackets, attach the brackets to the heater.
• Match the brackets to the slotted holes located on the bracket head shown in the
diagram.
• Using 2 Hex nuts bolts, tighten the heater brackets to the bracket head support
securely.
• Ensure the heater is centred on the post.
8
Hex Nut M12
QTY: 2
Pan Head Screw M6x10mm
QTY: 8
Tip: Tilt the stand on a chair or a solid non-abrasive surface before
connecting the heater to the bracket head.

10
Assembly Instructions
9Concealing Power Cord
• Place the plug into the circular hole located at the top of the upper
post. The plug should drop to the bottom of the heater, pull the cord
gently from the bottom hole. This step will conceal the cord and 3
pin plug.

11
Safety
HEATSTRIP Stand has an IP rating of X5. This means it is safe for water ingress from all directions. The HEATSTRIP
can be safely hosed down.
HEATSTRIP has undergone extensive testing both in laboratory conditions; in Thermofilm’s manufacturing facility in
Melbourne and field trials in Australia and overseas. It has been this testing that gives the purchaser the confidence of a
high quality product.
Independent laboratory testing has confirmed Thermofilm’s full compliance with Australian and other International
Standards. This includes CE, AS/ANZ, UL/CSE
HEATSTRIP is Class 1 equipment and must be earthed.
In operation, this heater is VERY HOT— do not touch any part of the heater while it is turned on. Do not touch any part
until 30 minutes after it is turned off.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or intellectual
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety. Children should be supervised to ensure they do not play with the
appliance.
Do not allow any cables, furnishings, flammable materials or other items come in contact with any surface of the heater.
If installed in wet areas, the heater switches or controls must be located so that they cannot be touched by persons in the
bath or shower.
The heater needs to be installed as per the installation instructions paying special attention to the minimum clearances.
The heater needs to be mounted on a rigid bracket or fixing.
The heater must not be mounted immediately below or in front of a socket outlet.
In case of a heater fault or damaged supply lead, the appliance should be returned to the point of purchase for return to
Cook & Heat B.V. for repair.
Maintenance
The HEATSTRIP® Stand is made from durable materials, however regular care and maintenance of your heater will help
prolong the life of the heater.
It is recommended that you clean the stand with a soft cloth, gently wipe the surfaces of the heater with a mild detergent to
remove the built up contaminants from the environment. Then rinse all detergent off the heater.
All chemicals in the atmosphere including cigarette smoke, pollution etc. will tarnish the surface of the heater. In this case,
additional cleaning and maintenance may be required. Carrying out the cleaning process at least every three months will
reduce the amount of build up and keep the HEATSTRIP in good condition. If the heater is in a corrosive environment eg.
salt spray, we recommend that you clean your heater with a light spray of fresh water every week. After cleaning, turn the
heater on for 20 minutes to dry any water residue and prevent water staining.
Before cleaning or inspection activity, the heater must be switched off and cooled down completely.
Do not use any abrasive materials or products to clean the heater, this includes solvents, citrus based cleaners or other
harsh cleaning products.
When handling the heater, ensure that your hands are clean or that you use clean gloves as grease or dirt can mark the
surface of the heater.
Do not use high pressure water to clean heaters.

12
Warranty Terms & Conditions
The below Warranty Terms and Conditions apply for international warranty only.
Cook & Heat B.V. warrants to the original owner that HEATSTRIP stand products will be free from defects in materials and
workmanship for a period of 24 months from the date of purchase in accordance with the following warranty terms and
conditions.
Provision of this warranty is subject to:
• The HEATSTRIP product must be installed in accordance with the Installation Instructions and relevant electrical
standards and codes.
• The HEATSTRIP product must be maintained and cleaned according to instructions detailed in the Installation Manual.
• There is no warranty expressed or implied with regard to capacity requirements. The selection of the unit or units
depends entirely upon the system design and capacities as determined by the purchaser.
• The customer has not repaired, opened or altered the product in any unauthorised manner.
• This warranty excludes damage to the product or components arising from circumstances outside the control of Cook &
Heat B.V., including, but not limited to, where the product is not used for intended purpose; where the product has
been rectified in any way; incorrect installation; incorrect power supply; damaged caused during delivery; misapplication,
misuse, abuse, vandalism, lack of maintenance or accident.
• Cook & Heat’s obligations under this warranty are limited to repair or replacement at Cook & Heat B.V. of any
components of the product which Cook & Heat B.V. identifies to its satisfaction to be defective.
• Transportation charges involved in return of the product to Cook & Heat B.V. is the sole responsibility of the customer.
• All products are inspected and tested before despatch and are at the risk of the purchaser after the shipment from Cook
& Heat B.V., if not delivered by Cook & Heat B.V. to destination.
• Discolouration of the surface may occur after a period of time, this does not constitute a warrantable event.
• Twisting and bending of the heaters may occur, this does not constitute a warrantable event.
• No products or components will be supplied in advance of an examination of the faulty product or components by Cook &
Heat B.V. or an authorized representative of Cook & Heat B.V.
• Cook & Heat B.V. does not participate in any site related costs or labour expenses incidental to replacement of parts,
repairing, removing, installing, servicing, transportation or handling of parts to complete products, and assumes no
liability on parts repaired or replaced without written authorisation. Cook & Heat B.V. shall not be liable for any default or
delay in performance of its warranty obligations caused by any circumstances beyond its control, including, but not
limited to, judicial or government restrictions, strikes, fires, floods, abnormal weather conditions, delayed supply of
components.
Should products be determined as damaged on arrival, immediately notify the transport company of the condition and have
them noted on the freight documents. If damage is discovered after unpacking, demand immediate inspection by the
transportation company and insist that a record of the damage is made on the freight documentation.
The customer warrants using the product in accordance with:
• Any instructions provided to it by Cook & Heat B.V. from time to time.
• All government and local regulations, including but not limited to all relevant electrical, environmental laws and
regulations governing the installation, storage, use, handling and maintenance of the goods.
• All necessary and appropriate precautions and safety measures relating to the installation, storage, use, handling and
maintenance of goods.
DISTRIBUTOR DETAILS FOR
EUROPE & UNITED KINGDOM
Distributed by: Manufactured by:
Cook & Heat B.V. Thermofilm Australia Pty. Ltd.
www.heatstrip.eu 17 Johnston Court
Dandenong South,
Victoria, 3175 Australia

Product & Assembly
Manual
HEATSTRIP® Portable Stand
(Dutch)

14
For repairs or replacement parts, please visit:
www.heatstrip.eu
Om de juiste vervangende onderdelen voor uw elektrische warmtestraler te verkrijgen,
zie de
onderdelennummers in deze onderdelenlijst. De volgende informatie is noodzakelijk om
zeker te zijn dat u
de juiste onderdelen ontvangt:
1. Model en serienummer (zie label op de straler)
2. Onderdeelnummer
3. Beschrijving van de onderdelen
4. Hoeveelheid benodigde onderdelen
Belangrijk: Gebruik alleen Thermofilm vervangende onderdelen. Het gebruik van onder-
delen die niet van
Thermofilm zijn, kunnen gevaarlijk zijn en uw garantie doen vervallen. Houd
deze handleiding om nog eens na te lezen en voor de vervangende onderdelen.
Inhoud
Manual # Rev A - Date:23/11/2018
Product Overview 15
Specifications 15
Product Features & Benefits 15
Installation Requirements 16
Parts List 16
Product Parts Diagram 17
Hardware Pack & Tools Required 18
Assembly Instructions 19
Electric Heater Assembly Instructions 19-22
Maintenance and Safety 23
Replacement Parts 23
Warranty 24
Dutch ___________________________________________________________________-13
French__________________________________________________________________________-25
German_________________________________________________________________________-37

15
Specificaties - Europe
MODEL DIMENSIONS (mm) WEIGHT (Kg)
THAC-100 1068(W) x 2050(H) x 500(D) 15
HEATER TYPE SUITABLE Design, Elegance, Intense, Max
APPROVALS AUSTRALIA/NZ/CE
BESCHERMINGSGRAAD IPX5 Protection from water ingress from all directions
LAND VAN HERKOMST Stand: Australie Powder coated mild steel
Kenmerken & Voordelen
• Stijlvolle, hoge kwaliteits, verplaatsbare en vrijstaande
stand.
• Ideaal voor buitengebieden, balkons, appartementen en
gastverblijven
• (intern en extern gebruik)
• Verborgen netsnoer zorgt voor een strak uiterlijk
• Componenten zijn voorgemonteerd voor eenvoudige
DHZ installatie
• Ingebouwde wielen voor eenvoudige verplaatsing, ideaal
voor gebruik in residentiëlen commerciële toepassingen
• Corrosiebestendig voor zelfs de zwaarste omgevingen
• 2 jaar residentiële en 1 jaar commerciële garantie
Tips
• Als een verlengsnoer nodig is, gebruik dan een zo kort
mogelijke, omdat een lang snoer kan leiden tot
prestatieverlies.
• Plaats de straler zo dicht mogelijk bij een stopcontact
• Deze verplaatsbare straler is alleen voor plaatselijk ver-
warmen. Plaats zo dicht mogelijk bij de plaats die u wilt
verwarmen (bijv. een tafel)
• Bewaar altijd onder een afdak

16
Parts List of THAC-100
Key Description QTY
Wheel
Skid Pad
Base
Kick Plate
Fixed Bracket
Post - Rear, Lower
Post - Rear, Upper
Post - Front, Lower
Post - Front, Upper
10 Side Panel / Left
11 Side Panel / Right
12 Rear Panel
13 Heater Bracket
14 Base Bracket
NOTE: Example Image

17
Parts Diagram
Key Description
1Wheel
2Skid Pad
3Base
4Kick Plate
5Fixed Bracket
6Post—Rear, Lower
7Post—Rear, Upper
8Post—Front, Lower
9Post—Front, Upper
10 Side Panel / Left
11 Side Panel / Right
12 Rear Panel
13 Heater Bracket
14 Base Bracket
13
10

18
Pan Head Screw M6x10mm
QTY: 39
Hardware Diagram for THAC-100
PART DESCRIPTION QTY PURPOSE OF PART
Hardware Pack For use in assembly of stand
Pan Head Screw M6 x 10mm 5Connecting Base
Pan Head Screw M6 x 10mm Install Base Brackets to Base
Pan Head Screw M6 x 10mm Install Lower Post to Base
Pan Head Screw M6 x 10mm
Install Side Panels to Lower Post & Base
Pan Head Screw M6 x 10mm
Pan Head Screw M6 x 10mm
Install Real panel to Side Panel & Lower Post
Pan Head Screw M6 x 10mm
Pan Head Screw M6 x 10mm Install Heater Bracket to Upper Post
Pan Head Screw M6 x 10mm Install Upper Post to Lower Post
Screwdriver
Pan Head Screw M6 x 10mm Install Lower Post to Base
Hardware Pack For THAC-100
Phillips Head Screwdriver
Flange Nut M6
QTY: 15
Hexagon Nut M12
QTY: 2

19
Assembly Instructions
VOORZICHTIG: Om deze stand te monteren, dient u hulp te krijgen van een andere persoon bij het hanteren van de
grotere, zwaardere onderdelen.
1
Installeer basisbeugels
• Verwijder alle verpakkingsmateriaal en zet op een niet schurend
oppervlak.
• Plaats de basis als getoond op de afbeelding.
• Zodra de sleufgaten zijn uitgelijnd, gebruikt u 5 platkop-
schroeven. Draai ze stevig vast met de meegeleverde moeren.
• Installeer twee beugels op de basis met 4 platkopschroeven
• (M6x10mm), als de beugels op hun plaats zitten draait u alle
schroeven stevig vast.
• Instelbare anti-slip pads worden meegeleverd. Schroef de pads
op elke hoek zoals getoond in het schema.
Opmerking: Basisbeugels kunnen worden verborgen als ze naar binnen
worden gekanteld.
• Bevestig de onderste staander aan de basis door de sleuf-
gaten van de onderste staander op de schroefgaten van de
basis te plaatsen. Schroef vervolgens 3 platkopschroeven
M6x10mm in de basis,
Onderste staander installeren
Basis in elkaar zetten
2
3
Pan Head Screw M6x 10mm
QTY: 4
Pan Head Screw M6x 10mm
QTY: 3
Flange Nut M6
QTY: 5
Pan Head Screw M6x 10mm
QTY: 5

20
Assembly Instructions
CAUTION: To assemble this heater, you should obtain assistance from another person when handling the
larger, heavier pieces.
• Plaats de twee zijpanelen op de basis.
• Installeer het linker zijpaneel aan de onderste staander met 2
plat- kopschroeven (M6x10mm). Plaats vervolgens het linker
zijpaneel opde basis overeenkomend met de sleufgaten. Als de
sleufgaten overeenkomen, gebruik dan 3 platkopschroeven
(M6x10mm) en draai deze stevig vast met de moeren.
• Herhaal dezelfde handeling voor het rechter zijpaneel, draai
vervolgens alle schroeven stevig vast.
Zijpanelen installeren
4
• Plaats en installeer het achterpaneel aan de onderste
staander met behulp van.
• Zodra de bovenste 2 platkopschroeven zijn geplaatst, pas
dan de sleufgaten van het achterpaneel op de zijpanelen.
Gebruik de 4 platkopschroeven (M6x10mm) en
flensmoeren om alle 4 gaten stevig vast te schroeven.
• Plaats de beugelkop op de bovenste staander.
• Gebruik de beugelkop om de sleufgaten op de bovenste
staander uit te lijnen. Zodra de sleufgaten zijn uitgelijnd, ge-
bruikt u 4 platkopschroeven (M6x10mm), draai vervolgens
stevig aan zoals getoond in het schema.
• Zorg dat de beugel in de juiste richting is geplaatst, volgens het-
schema.
Installeer achterpaneel
Installeer de beugel aan de bovenste staander
5
6
Pan Head Screw M6x10mm
QTY: 6
Pan Head Screw M6x10mm
QTY: 10
Pan Head Screw M6x10mm
QTY: 4
Flange Nut M6
QTY: 6
Flange Nut M6
QTY: 4