Rivers Edge BIG FOOT XL LOUNGER RE552 User manual

Operator's Manual
Hang-On Stands
GAS/OIL
RATIO
50:1
P/N: 18051
REV5: 03/15/16
© 2016 RETI
All Rights Reserved
Get parts online at
www.HuntRiversEdge.com
PARTICIPATING MEMBER
PRODUCT MEETS
INDUSTRY STANDARDS
RECOGNIZED BY
BIG FOOT™ TRAVELER
Model RE513
BIG FOOT™XL LOUNGER
Model RE552
INCLUDES MODEL #'s:
RE513, Big Foot™ Traveler
RE552, Big Foot™ XL Lounger
Wear Your
Harness!

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-52
Operator's Manual
Hang-On Stands
CONTENTS
Introduction/Warranty ..................................................................................................................................................................................................................2
Warnings.........................................................................................................................................................................................................................................3-4
Inspection and Maintenance ......................................................................................................................................................................................................4
Assembly Instructions (RE513) ...................................................................................................................................................................................................5
Assembly Instructions (RE552) ...................................................................................................................................................................................................6
Warnings.............................................................................................................................................................................................................................................7
Set Up and Use Instructions ........................................................................................................................................................................................................8
Threading the Float Buckle..........................................................................................................................................................................................................9
Parts Explosion/Parts List (RE513) .......................................................................................................................................................................................... 10
Parts Explosion/Parts List (RE552) .......................................................................................................................................................................................... 11
INTRODUCTION
Rivers Edge® Treestands are engineered with you the hunter in mind. We appreciate your purchase of one of our world
class treestands. Follow these few simple instructions and your stand will provide you many years of trouble-free
pleasure. Instructions should be kept in a safe place and reviewed at least annually.
If for any reason you have a problem with your product, DO NOT return to the retailer, contact the Rivers Edge®
customer service department at 800-450-EDGE (3343) for assistance.
WARRANTY
RETI oers a one year warranty for all components of the treestand. These warranties apply to the original owner with a proof of purchase. These warranties
begin on the date of purchase by the rst retail consumer and continue for the period specied above. These warranties apply to products that are not
modied, abused or used in a manner that deviates from the product’s intended usage. Minor fading in color is normal and is not covered by warranty.
Any corrosion of painted surfaces that occurs as a result of paint being removed or damaged is also not covered by warranty. RETI oers no other warranty
expressed or implied. Products for which warranty work has been approved must be sent directly to RETI and performed by RETI. To obtain warranty service
and/or replacement instructions, you must obtain prior approval from RETI before shipping your package to us by calling our customer service
department at 800-450-3343 or by writing to: RETI, P.O. Box 755, 1160 Eighth Avenue, Cumberland, WI 54829 for a return material authorization
number (RMA#). All items must be shipped prepaid. RETI will, at no charge, repair or replace, in RETI’s sole discretion, any product that satises the conditions
stated above. RETI retains the right to change models, specications and price without notice.
This equipment has been manufactured under strict quality and safety guidelines. As with any equipment of this type, full understanding of the instructions
and its use is mandatory and imperative for the safety of its user. RETI is not responsible for any damages or injuries sustained due to improper use or
modication of any of its products, or resulting from any use which deviates from the product’s intended usage. RETI is not responsible for any injuries
sustained due to failure to read and adhere to the instructions for use. Any misunderstanding or questions regarding the products of their use should be
directed to RETI prior to any use. All RETI treestands are sold with a full body harness (“Fall Arrest System”) that meets standards set by the Treestand
Manufacturer’s Association (“TMA”). It is the owner's sole responsibility to inspect the product regularly for damage, improper installation, or conditions
that could jeopardize the ultimate safety of the product. Failure to use or improper use of the provided Fall Arrest System may result in serious injury or death.
ALWAYS wear the provided Fall Arrest System while using this product. Owner is responsible to understand and follow product eld weight rating
and must never exceed maximum weight rating. RETI is not responsible for any malfunction or injury resulting from normal wear and tear, damage caused
by improper use, improper maintenance, negligence or accidents. This product, if used safely as intended, will provide trouble free service for the useful life
of the product. We hope you will enjoy the quality of our products for years to come, and have a safe hunt.

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 3
Operator's Manual
Hang-On Stands
MODEL RE513 / RE552
MAXIMUM OCCUPANCY  ONE 1
TOTAL WEIGHT LIMIT  300 LB
TREE DIAMETER RANGE  8"TO 20"
WARNING
This product carries strict weight restrictions. Do Not use
this product if you exceed the total weight limit. Please
note that the total weight limit includes the user(s) and
their equipment.
WARNING
Pull up a bow, backpack, or rearm or other equipment
only after being secure in the treestand and a rearm
must be pulled up with it unloaded, chamber open, and
muzzle down.
Always inform someone of the hunting location, where
the treestand will be located and the expected duration
of the hunt.
A signal device such as a mobile phone, radio, whistle,
signal are or personal locator device (PLD) must be on
your person and readily available at all times.
Inspect the treestand and all safety devices each time
before use and Do Not store a treestand outdoors when
not in use.
Never modify your treestand in any way by making
repairs, replacing parts, or altering it except if explicitly
authorized in writing by the manufacturer.
Practice installing, adjusting and using your treestand at
ground level prior to using it at elevated positions. Study
your new stand to become familiar with all of its features
and design. Doing so will conrm that the product is
manufactured, assembled and installed correctly.
Instructions (written and video) shall be kept in a safe place
and reviewed at least annually. It is the responsibility of
the treestand owner to furnish the complete instructions
to any person who borrows or purchases the treestand.
The use of a lineman’s/climbing belt is required when
installing a hang-on treestand to stabilize the user with
the tree.
Correct tightening and adjustment of chains, cables,
straps, etc. are critical to stable hang-on treestand
installation. All treestand contact points must be in
contact with the tree before you step onto your stand.
Never leave a treestand in a tree for more than two weeks
since weather or animals could cause damage. Tree
growth can also stress and damage straps and buckles.
Practice the attachment of hang-on treestands at ground
level before using in a hunting environment. Doing so
will conrm that the product is manufactured, assembled
and installed correctly. Failure to install and test at ground
level rst puts users at risk for serious injury or death.
Use a haul line to raise and lower the treestand. Never
climb with anything on your back.
Always lean forward as you ascend or descend ladder or
climbing aid.
Never lean out over edge of device.
WARNING
When hunting from a treestand falls can occur any
time after leaving the ground causing injury or death.
Always wear a Fall Arrest System (FAS) comprising a full
body harness at all times after leaving the ground. You
must stay connected at all times after leaving the ground
while using climbing and hang-on treestands. Single
safety belts and chest harnesses are no longer allowed
and shall never be used. If you are not wearing a full body
harness properly attached to the tree that is protecting
you from a fall, do not leave the ground.
Read and understand all of the manufacturer’s Warnings
and Instructions and use all safety devices provided by
the manufacturer. Contact the manufacturer for any
questions. Failure to do so could result in injury or death.
Never exceed the total weight limit of the treestand.
Never use a treestand during inclement weather such as
rain, lightning, windstorms or icy conditions and end your
hunt and return to the ground if inclement conditions
arise.
Never use a treestand while using drugs (even
prescription drugs) or alcohol.
Never use a treestand while feeling ill, nauseous or dizzy,
or if you have a prior medical condition that could cause
a problem, that is, heart condition, joints that lock-up,
spinal fusions, etc., or if you are not well rested. Never
sleep in stand.
Never use a treestand on a dead, leaning, diseased or
loose barked tree, or a utility pole. Always avoid electrical
power lines.
Never rely on a tree branch for support.
Never jump or bounce on a treestand to seat it to the tree.

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-54
Operator's Manual
Hang-On Stands
WARNING
Climbing aids (stick ladders, sectional ladders, steps, etc.)
must extend above the platform to allow the user to step
down onto the platform. Never step up to your stand from
a climbing aid. To ensure that you step down onto the
platform, the maximum recommended use height is ve
feet less than the height of the climbing aid being used.
Do Not use this product until you have watched the
included treestand safety DVD, understand it, and practiced
the techniques for safe hunting discussed in this DVD.
Read and perform all inspection and maintenance tasks
before each and every use. Replace any questionable
components immediately with RETI original replacement
parts.
Do Not crush tubing when tightening bolt assemblies!
Identify and familiarize yourself with all parts before you
start. A bolt identication cart can be found in the back.
Double check assembly steps to be certain you have
correctly assembled this product.
Never use any product that has not been maintained or
inspected properly - Your life depends on it!
Replace any and all treestand straps every two years or
when signs of damage or wear exist before.
Do Not use any type of after market hanging assists,
bracket mount systems or any other type of mechanism
to attach your hang-on treestand to a tree. These types of
devices can negatively aect the stability of the treestand
in the tree and reduce or prevent proper tightening, tree
adhesion and performance of the treestand to the tree
which can lead to serious injury or death.
Platform must be folded up to remove stand! This allows
slack in strap for removal.
Always climb tree on the oat buckle side of this treestand.
Visually inspect that both sewn loop attachments are
securely connected to be assured you have correctly
attached stand to tree as per instructions and Figures.
Always wear the appropriate footwear when using a hang-
on treestand. A good non-slip safety boot is important to
your personal safety. Be especially careful that boot laces
do not get hooked on the stand or any of its components
(tuck shoelaces into boots before climbing).
Never touch or move buckle while stand is in use.
INSPECTION AND MAINTENANCE SCHEDULE
BEFORE EACH USE PERFORM THE FOLLOWING:
• Inspect all webbing, rope, cord, and strap assemblies for
wear or damage.
• Inspect cables and/or cable ends for damage or kinking.
• Inspect all hardware and chain components for damage.
• Inspect for any structural damage to product. (If any exists
call RETI customer service.)
• Inspect all nut and bolt assemblies to be certain none are
loose.
• Inspect for any missing parts.
• Lubricate all pivot and slide together points with powder
graphite, petroleum jelly or silicone spray to prevent noise,
wear and rust.
• Inspect entire product for any rust, corrosion, cracks,
freezing, excessive heat or rotting damage that may eect
the safety of your product. Discard any questionable
product.
• Inspect entire product for any structural damage - pay close
attention to all weld locations. (Return to factory for repair or
discard product if any damage is found.)
• Using correct wrenches inspect all nut & bolt assembly
locations and snug up any that may be loose. Be careful not
to crush tubing when tightening!
• Inspect and check operation of all cables, cable ends, cord,
rope, webbing, and strap or chain assemblies. Replace with
factory new any item or assembly that shows signs of wear,
damage, kinking, or functions incorrectly.
• Inspect seat. Replace any seat with factory new that shows
signs of structural damage or wear.
• Inspect all hardware for wear or damage, also be sure you
have no missing parts.
• Never modify your stand in any way by making repairs,
replacing parts, or altering adding or attaching anything to it
except if explicitly authorized in writing by the manufacturer.

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 5
Operator's Manual
Hang-On Stands
8
ASSEMBLY INSTRUCTIONS RE513
Tools needed – two 7/16" wrenches, two 1/2" wrenches
IMPORTANT ASSEMBLY TIP: Do not tighten any nut and bolt combi-
nations completely until all parts are assembled together! Finger
tighten plus one turn of a wrench only! This will temporarily hold the
lock nut on the bolt while helping alignment of all parts! After all parts
are assembled together, all nut & bolt combinations must be com-
pletely tightened.
1. Bolt the metal seat frame (C33) onto the seat post using the (2) provided
1/4-20 x 2-1/4" bolts, locknuts and (6) nylon washers. SEE FIGURES 1.
DO NOT tighten all nut & bolt assemblies completely!
2. Attach removable seat cushion to metal seat frame by sliding seat
frame into pocket. Wrap the Velcro seat straps or buckle straps
around seat frame and secure together. Snap the side release buckle
together for buckle style seats. Pull straps tight so seat is not loose.
3. Bolt cables onto platform using the (2) provided 5/16-18 x 1-1/2" bolts,
locknuts and steel washers. SEE FIGURE 2.You must now tighten all
nut & bolt assemblies. Be sure not to over tighten or crush tubing
when tightening!
NOTE: Using powder graphite lubricant during assembly of moving
parts will help eliminate noise during use!
FIGURE 1
1/4-20 x 2-1/4" bolts
nylon washers
locknuts
seat frame
seat post
platform cable
5/16-18 x 1-1/2" bolts
steel washers
locknut
FIGURE 2

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-56
Operator's Manual
Hang-On Stands
ASSEMBLY INSTRUCTIONS RE552
Tools needed – two 7/16" wrenches, two 1/2" wrenches
IMPORTANT ASSEMBLY TIP: Do not tighten any nut and bolt combina-
tions completely until all parts are assembled together! Finger tighten
plus one turn of a wrench only! This will temporarily hold the lock nut on
the boltwhile helping alignmentof allparts!After allparts are assembled
together, all nut and bolt combinations must be completely tightened.
1. Attach the seat frame weldment (CXR15) to the seat post (CXR14) using
(2) provided 1/4-20 x 2-1/2”bolts, locknuts and (6 to 8) nylon washers.
SEE FIGURE 3. DO NOT tighten all nuts and bolts completely!
NOTE: You may need to place 2 nylon washers between seat post
upright and seat frame to take up necessary gap.
2. Attach cable (48212) ends to the platform (CXR12) using (2) provided
5/16-18 x 1-1/2” bolts, locknuts and steel washers. SEE FIGURE 4.
You must now tighten all nut & bolt assemblies securely. Be sure
not to over tighten or crush tubing when tightening!
NOTE: Using powder graphite lubricant during assembly of moving
parts will help eliminate noise during use!
3. If included, attach backpacking straps (48067) at desired location
on platform. Fold strap in half. Feed folded strap through platform
mesh. Feed the two loose ends of strap through folded loop and pull
tight forming a cinch knot. SEE FIGURES 5A AND 5B. Feed straps
through platform mesh and secure with provided tri-slide buckles.
SEE FIGURES 5C
4. Attach padded seat (48103) by feeding straps around the lower portion of
seat frame. Feed the long strap through both metal tri-slides that are sewn
to opposite side of strap. Wrap the long strap back around one tri-slide
and through the second tri-slide and pull tight. SEE FIGURE 6. Repeat
the same operation for the other seat strap. Adjust as needed to achieve
desirable seat height. Excess strap can be tucked away using provided
Velcro tabs under the seat.
5. Attach (2) provided 9" camo arm pads (48736) to upper portion of
seat frame weldment by wrapping around tubing and attaching
Velcro together.
FIGURE 6
FRONT VIEW OF
SEAT ASSEMBLY
pull to
tighten
FIGURE 5A FIGURE 5B
FIGURE 5C
platform cable
5/16-18 x 1-1/2" bolts
steel washers
locknuts
FIGURE 4
locknuts
nylon washers
nylon washers
(2 if needed)
1/4-20 x 2-1/2"
bolts
nylon washers
FIGURE 3

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 7
Operator's Manual
Hang-On Stands
WARNING
Double check assembly steps to be certain you have
correctly assembled this product.
Practice installing, adjusting and using your treestand at
ground level prior to using it at elevated positions. Study
your new stand to become familiar with all of its features
and design. Doing so will conrm that the product is
manufactured, assembled and installed correctly.
Always wear the appropriate footwear when using a hang-
on treestand. A good non-slip safety boot is important to
your personal safety. Be especially careful that boot laces
do not get hooked on the stand or any of its components
(tuck shoelaces into boots before climbing).
Climbing aids (stick ladders, sectional ladders, steps, etc.)
must extend above the platform to allow the user to step
down onto the platform. Never step up to your stand from
a climbing aid. To ensure that you step down onto the
platform, the maximum recommended use height is ve
feet less than the height of the climbing aid being used.
Do Not twist strap when attaching. See setup and use
instructions for correct attachment.
Always climb tree onthe attachmentside ofthis treestand.
Visually inspect your connection to be assured you have
correctly attached stand to tree as per instructions and
diagrams.
The use of a lineman’s/climbing belt is required while
ascending, descending and installing a hang-on treestand
to stabilize the user with the tree.
Correct tightening and adjustments of chains, cables,
straps, etc. are critical to stable hang-on treestand
installation. All treestand contact points must be in
contact with the tree before you step onto your stand.
Platform must be folded up to remove stand! This allows
slack in strap for removal.
Never touch or move buckle while stand is in use.
If seat is removable, be certain it is securely attached
when in use.
Never stand on seat, it is designed for sitting only.
Some models include a footrest, which is designed as a
footrest only. Never stand on footrest! Always be fully
aware of foot placement.
WARNING
All users are responsible for ensuring strap is attached
to treestand properly and securely. Failure to do so may
result in serious injury or death. Read and understand
all instructions for proper installation procedure and
product warnings before use.
WARNING
Only use approved RETI parts. Failure to do so may result
in serious injury or death!
WARNING
It is critical to familiarize yourself with how the strap
attaches to the stand. Practice attaching the stand to the
tree several times at ground level before ascending up
the tree.

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-58
Operator's Manual
Hang-On Stands
SETUP AND USE INSTRUCTIONS
RE513 & RE552
During installation and removal of a hang-on treestand, you must
always and properly use the included Full Body Harness (Fall Arrest
System) with climbing belt. Refer to the Full Body Harness and
climbing belt instructions included with this product for proper use.
You must always use the Full Body Harness while using this product.
1. At desired height, attach by following instructions - a,b,c,d,e,f.
NOTE: Stand should be attached to tree with platform folded in
an upright position!
a. Lengthen strap by pulling buckle away from strap - this will allow
strap to slide around buckle roller bar.
b. Take snap hook/buckle end and wrap around tree. Be sure the
strap is even and at the same level all the way around the tree. Also,
be sure there are no twists in the strap. Connect hook to opposite
side of stand by inserting through slot provided. Be absolutely sure
snap hook engages through slot of bracket and can not come o.
SEE FIGURE 7
c. Pull on excess end of strap rmly - snugging up stand to tree.
SEE FIGURE 8
NOTE: Platform must be folded up while doing this.
d. While platform is still folded up, push treestand in a downward
direction to further tighten strap. SEE FIGURE 9
e. Once securely attached, pivot the platform down.This lever-action
will snug stand up tight to tree to prevent any shifting. Redo as
necessary to accomplish a snug stand-to-tree t. All four contact
bars must be touching tree! SEE FIGURE 10
f. The tension on strap will not allow any slippage due to roller bar
tension of buckle. Proper installation should be checked prior to
stepping onto platform to ensure safety.
2. Before stepping down onto center of stand platform, be sure it is secured
properly and is tight against tree with all (4) contact bars touching tree!
3. Carefully step onto stand platform to be sure you have a solid feel
against tree and platform is level. Seat folds down for sitting and tips
back for standing.
4. RE552 ONLY. Attach backrest portion of seat to tree by wrapping
the long strap with buckle end around tree and snapping together
with opposite end. Adjust as needed.
NOTE: To remove stand, fold platform back up and pull on buckle hand
strap to release tension on roller bar.
TREE
TREE
FIGURE 7
FIGURE 8 FIGURE 9
FIGURE 10
excess end
of strap
platform
seat

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 9
Operator's Manual
Hang-On Stands
THREADING THE FLOAT BUCKLE
Always check the condition of your Big Foot strap before use. If strap
becomes twisted or if you need to replace a worn or damaged strap,
make sure to follow these instruction to ensure proper assembly.
1. Hold oat buckle so warning tag faces upward. SEE FIGURE 11
2. Feed end tail of strap up through the bottom of the oat buckle on
the snap-hook side of the roller bar. SEE FIGURE 12
NOTE: Smooth side of end tail must face snap-hook.
3. Feed end tail over roller bar and down through oat buckle.
SEE FIGURE 13
4. Pull end tail away from oat buckle. SEE FIGURE 13
!
FIGURE 13
FIGURE 11
!
warning tag
oat buckle snap-hook
!
FIGURE 12
snap-hook
roller bar
end tail
of strap smooth side
WARNING
All users are responsible for ensuring strap is attached
to treestand properly and securely. Failure to do so may
result in serious injury or death. Read and understand
all instructions for proper installation procedure and
product warnings before use.
WARNING
Only use approved RETI parts. Failure to do so may result
in serious injury or death!
WARNING
It is critical to familiarize yourself with how the strap
attaches to the stand. Practice attaching the stand to the
tree several times at ground level before ascending up
the tree.

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-510
Operator's Manual
Hang-On Stands
6
7
5
5
12
5
8
11
9
2
1
4
63
9
10
8
6
6
BIG FOOT™ TRAVELER
Model RE513
HANGON PARTS EXPLOSION RE513
KEY # PART # DESCRIPTION QT Y.
1 8655B BOLT 5/1618 X 13/4" HH BLK ZN 2
2 48210 CABLE 26" BLACK VINYL W/
BLACK ENDS
2
3 48152 BOLT 5/1618 X 11/2" HH BLK ZN 2
4 48250B BOLT 1/420 X 13/4" HH BLK ZN 2
5 WN516 WASHER 5/16" NYLON, BLK 6
6 WF516B WASHER 5/16" FLAT BLK ZN 8
7 48271B BOLT 1/420 X 21/4" HH BLK ZN 2
8 48752B NUT 1/420 FLANGE NYLOCK BLK
ZN
4
960G5NYB NUT 5/1618 FLANGE NYLOCK
BLK ZN
4
10 CB18 PLATFORM 1
11 C19 SEAT POST 1
12 C33 SEAT FRAME 1
ITEMS BELOW NOT SHOWN
 RE760 TREE STRAP ASSEMBLY 1
 10531 FULL BODY HARNESS FAS 1
 15599 CLIMBING BELT 1
 48101 SEAT PAD 1
 48800 DVD TREESTAND SAFETY 1
HANGON PARTS LIST RE513

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 11
Operator's Manual
Hang-On Stands
HANGON PARTS EXPLOSION RE552
KEY # PART # DESCRIPTION QT Y.
1 1423B BOLT 5/1618 X 2 HHCS
GR5 BLK ZN
2
2 48153B BOLT 1/420 X 2 HHCS
GR5 BLK ZN
2
3 48212 CABLE 28" BROWN VINYL 2
4 48152 BOLT 5/1618 X 11/2 HHCS
GR5 BLK ZN
2
5 48270B BOLT 1/420 X 21/2 HHCS
GR5 BLK ZN
2
6 WF516B WASHER FLAT 5/16" STANDARD
BLACK ZN
8
7 WN516 WASHER, 5/16", BLACK NYLON 10
860G5NYB NUT 5/1618 NYLOCK BLACK 4
9 48752B NUT, FLANGED, NYLOCK, 1/420 4
10 CXR14 WELDMENT, FTS, SEAT POST
LOUNGER
1
11 CXR15 WELDMENT, SEAT FRAME,
LOUNGER
1
12 CXR12 WELDMENT, PLATFORM,
LOUNGER
1
ITEMS BELOW NOT SHOWN
 RE760 TREE STRAP ASSEMBLY 1
 10531 FULL BODY HARNESS FAS 1
 15599 CLIMBING BELT 1
 48103 SEAT W/ BACKREST, LOUNGER
HANGON
1
 48736 CAMO ARMREST PAD, 9" 2
 48067 KIT, BACKPACK STRAPS 1
 48800 DVD TREESTAND SAFETY 1
7
9
11
7
7
5
10
66
1
3
7
7
2
9
12
6
4
6
8
8
HANGON PARTS LIST RE552
BIG FOOT™ XL LOUNGER
MODEL RE552

*All weights, specications and features are approximate and are subject to change without notice. Due to continuous product improvements, product images may not be exact. Warning labels in some product images
may have been removed for photography purposes only. Props shown in photos not included. Some assembly may be required.
Rivers Edge® Treestands, Inc.
1160 Eighth Avenue, PO Box 755
Cumberland, WI 54829
800-450-EDGE (3343) | Fax [phone]
Email: [e-mail]