Hema Navigator Instruction manual

2
H E M A N AV I G AT O R
QUIC K USE R G U I D E
POWERED BY

Getting Started
2
What is in the box?
- HEMA NAVIGATOR GPS unit
- Suction windscreen mount
- 12V car charger
- 240V AC charger
- USB cable
- Quick User Manual
- SD Card
serial #: HNV11008050001
Speaker
RESET
Reset button
(push lightly with pen)
External GPS
Aerial Port
Stylus pen
4.3” 16:9 Touch LCD Screen
Indicator lights
Red = Charging
Green = Battery full
Orange = no GPS lock
SD card slot
3.5 mm Headphone
Jack
Power & Mini
USB connector
Power
press for 2 sec to
turn on/off
Top cradle
mount slot
Exit Navigation

Step 1: Mount the GPS
Select a suitable location to mount the GPS on your windscreen.
Clean & dry the suction cup and windscreen.
Plug the Car Charger into the right side of the GPS.
Attach the cradle to the suction windscreen mount.
Adjust the angle with the rotary clamp if necessary.
Place the suction cup on the windscreen and flip the back lever
towards the windscreen.
Press the bottom of the GPS on to the cradle and gently ‘snap’ the top
of the GPS into the cradle.
Plug the car charger into a power outlet in your vehicle. Your unit
should turn on automatically if it is plugged in and your vehicle key is
turned to ON/ACC.
Ways to charge the GPS
Connect the 12V car charger to the GPS and to a power outlet in your
vehicle.
Connect the AC adaptor to the GPS and a 240V AC wall outlet.
Connect the USB cable to the GPS and charge it from a PC.
Turn on your GPS, press the button for 2 sec
Turn off your GPS, press the button for 2 sec
1.
2.
3.
4.
5.
6.
-
-
-
Step 2: Turning on your GPS
Step 3: System Menu Options
Battery Status
Touch To Start
Street Navigation
Touch to Start 4WD and
Topographical GPS
Main Menu: Tools & Settings

To Start Street Navigation
Acquiring Satellites
Before the HEMA Navigator can find your location and navigate a route,
it requires GPS satellite lock.
1. Go outdoors to an open area, GPS position detected
away from tall buildings & trees.
2.Turn on the HEMA Navigator and
start Street Navigation. Acquiring
GPS lock may take a few minutes.
Acquiring GPS lock screen Position shown on map
No GPS lock
When a valid GPS position is
established, the unit will automatically
zoom to street level.Your GPS
position is indicated by a red dot.
No GPS detected
Your GPS position cannot be
detected. If indoors, GPS signal may
not be detected.
If GPS position cannot be detected
after 10 mins, reset your device &
try again.
Touch to start Street Navigation

What's on the map screen?
Main
Menu
Zoom
Out
Zoom
In
Next Turn Road Name
Map
Current Road Name Battery
Status GPS
Signal
Strength
Compass
(Red points North)
Next
Turn
Turn
After
Next
Speed
Remaining
Distance
Remaining
Time
ETA
Distance to
next turn
Press to change
keyboard layout
Finding an address
1. Touch to enter the MAIN MENU > touch NAVIGATE TO >
LOCATIONS > a keyboard will appear for address input.
2.To input an address, simply enter
HOUSE NUMBER (Space) first 4 letters of the STREET NAME (Space) first 4
letters of the SUBURB, then hit
E.G. for 217 Flinders St Melbourne, type in 217 FLIN MELB
KEYBOARD: (QWERTY layout) To search the data base simply
enter
The House Number > first 4
letters of the street name >
first 4 letters of the suburb name.
Navigating to a destination

A list of available locations will
appear. Select the most appropriate
location and touch to start
navigation.
There may be too many
locations to choose from.To refine
a search, go to the previous screen
and enter more characters to either
street name or suburb.
If you do not have the HOUSE NUMBER or STREET NAME or SUBURB? Don’t
worry, just type in the information you have. QuickSearch will identify the
closest match in it’s database and display a number of locations you can
choose from.
for Flinders St Melbourne, type in FLIN MELB
for Melbourne, type in MELB
for Flinders St, type in FLIN
for 217 Flinders St, type in 217 FLIN
NOTE: Do not input the road type such as St, Street or Rd, Road. etc
Need more help?
There are a host of other software features not covered by this quick user
manual
For further assistance on your street navigation, go to the MAIN MENU >
Scroll down > HELP.There you will find help topics.
www.hemanavigator.com.au
For further assistance, please visit
CLICK ON SUPPORT

To Start OziExplorer
Acquiring Satellites
Before the HEMA Navigator can find your location, it requires GPS satellite lock.
Red = No GPS lock, Green = GPS lock
Touch to start OziExplorer
To open a map, either select on the Main Tool bar, FILE > OPEN MAP FILE. Or
click the OPEN MAP ICON.
1. Go outdoors to an open area, away
from tall buildings & trees.
2.Turn on the HEMA Navigator and
start OziExplorer. Acquiring GPS lock
may take a few minutes.
3. Press or to scroll through
various screen views.
Select the desired map file and press OK button
map files
Folders Scroll
Up/Down
OK button
Open A Map

Waypoints
What is a waypoint?
A waypoint is a user created position on a map.Waypoints can be used for
a wide range of things from marking points of interest to camp sites, to
fishing hotspots on rivers and lakes, landmarks etc, that you may wish to
return to. You can save waypoints and swap them with your friends.
Using the Waypoint Toolbar
The Waypoint Toolbar can be accessed by selecting VIEW > TOOLBARS >
WAYPOINT TOOLBAR.
Add a Waypoint - If selected, a waypoint is added at the position on the
map where you touch.
Delete Waypoints - All waypoints are deleted from the map.
Display Waypoint List - A list of waypoints on the map is displayed.The
list shows information about each waypoint.
Load a Waypoint File - Select a waypoint file (.wpt) to load onto the map.
Save Waypoints to File - All waypoints currently on the map are saved to
a waypoint file (.wpt).
Show/Hide Waypoint Name - Waypoint names are displayed on map /
or not.
Auto Show Waypoint Properties - If selected, the waypoint properties
dialog is shown automatically when a new waypoint is added. Changes
to the name and description of the waypoint can be made.
Close - Turns off waypoint toolbar.
By default, Proximity warning to Waypoints is activated. Alarm is triggered
when you come within a certain distance of the waypoint.These can be
used to inform of arrival at locations or to warn of sharp drops or inclines.
Proximity Warning

Route
Routes are a series of waypoints linked together.
Using the Route Create Toolbar
The Rout Create Toolbar can be accessed by selecting VIEW > TOOLBARS >
ROUTE CREATE TOOLBAR.
Add a Route Waypoint - If selected, a Route waypoint is added at the
position on the map where you touch.
Delete Route - The current route displayed is deleted from the map.
Display the Route Properties Dialog - The properties dialog displays a
list of the route waypoints.
Load a Route - the selected route is loaded to the map.
Save Route to File - The currently loaded route is saved as a (.rt2) file.
Show/Hide Route Waypoint Name - If selected, route waypoint names
are displayed.
Close - Turns off Route Create toolbar.
Insert a Route Waypoint - If selected, a route waypoint is inserted
between two waypoints or at the start or end of the route depending
on a best choice.
How to create a Route
Bring up the Route Create Toolbar by selecting VIEW > TOOLBARS > ROUTE
CREATE. Select the Add a Route Waypoint button. Using the Stylus, insert
any number of waypoints by tapping on the screen.
When you have finished creating a route, select Save Route to File from the
Toolbar to save the created Route to file for later use.

Navigation
When a Route has been plotted on the map, it allows Voice activated navigation to each of its
waypoints.
1. Select the button on the tool bar & select Route Navigation Page.
2. Select to active the Navigation Toolbar. Select Start Route Forward button.
You will notice a Yellow/Red navigation line pointing as the crow flies to the nearest waypoint
in that route.This is a graphical indication of your relative position to that waypoint. On the
side is all the relevant information to aid in navigation.
Route Navigation Page
Current Speed Current Heading
Bearing
to WP
Distance
to WP
Distance
Remaining
in Route
Navigation Toolbar
Map Zoom Level
Zoom
In
Zoom
Out
While navigating, when a WP (waypoint) is reached, you will hear voice instruction on how to
proceed. Once the WP is passed, it will automatically proceed to the next WP in route.
Reverse Navigation.
In some circumstances, you may want to navigate from the last WP to the first WP. To do so,
select the Navigation Toolbar and select Start Route Reverse.
Stop Navigation.
To cancel navigation, select the Navigation Toolbar and select Stop Navigation.

Accessing Maps
All OziExplorer maps are stored on the SD card under the folder“Hema Maps”. To add new
map files to the SD card, be sure to copy them into the same same folder.
Accessing Waypoint files
All OziExplorer waypoint files (.wpt) are kept in the“OziData” folder in the root directory
of the SD card.To add waypoint files, copy them into the same “OziData” folder.
Accessing Route files
All OziExplorer route files (.rte) are kept in the“OziData” folder in the root directory of the SD
card.To add route files, copy them into the same“OziData” folder.
Accessing Track files
All OziExplorer track files (.plt) are kept in the “OziData”folder in the root directory of the SD
card.To add track files, copy them into the same“OziData”folder.
Exit OziExplorer
To exit OziExplorer, select FILE > QUIT or select than
For a detailed instruction manual on OziExplorer, visit
www.hemanavigator.com.au
CLICK ON SUPPORT
DETAILED PERSONAL TRAINING & HELP
Go to the website for training locations near you.

4
Tools Page 1 of 2
Tools Page 2 of 2
Volume Menu:
Start
Memory Map
Change
Time
Change Volume
Change Brightness
Change
Language Options
Next Tools Page
Calculator
System Power
Decrease
System
Volume
Increase
System
Volume
Back to settings menu
Back to main menu
Back to main menu
Previous
Tools Page
mp3 Player
System Options

Language Menu:
Power Menu:
Time zone Menu:
decrease
Idle time
increase
Idle time
Adjust for
Daylight
Savings
change
time zone
back to settings menu
back to settings menu
back to main menu
Time zone information
Change Language
adjust
time & date format

Resetting your GPS
If your unit is responding slowly or is not responding at all, it may need to
be reset.
1. Press the RESET button on the back of the unit.
2. Connect the GPS to a power source.
Systems Menu:
Calibrate Touchscreen
Update System Firmware
Memory Map Support
visit the support page at
www.memory-map.co.nz
or call (AUS) 1900 9 MEMORY (1900 9 63667)
or (NZ) 0900 MEMORY (0900 63667)
$2.50 first min then $0.50. ex GST, ask bill payer first

VICTORIA
TASMANIA
Sydney
Hobart
Port Augusta
Hay
Port Macquarie
Broken Hill
Warrnambool
Mount
Gambier
NEW SOUTH
WALES
Adelaide
North East NSW
Flinders Ranges
Fraser Island
South East NSW High Country
Great Desert
Tracks North
Central Sheet Cape York
Tropical North Queensland Lakefield Nat Park
Newcastle
Canberra
Vulkathunha
-Gammon
Ranges NP
East Gippsland
Lakes Entrance
Wagga Wagga
Darwin Region
Great Desert
Tracks North
East Sheet
Mt Remarkable
NP
Karijini NP
Nhulunbuy Region Tasmania
Keep River NP
Francois Peron NP
Carnarvon
Geraldton
Perth
Albany
Esperance
Port Lincoln
Kalgoorlie
AUSTRALIA
Warburton
Wiluna
Coober Pedy
WESTERN
SOUTH
AUSTRALIA
TERRITORY
NORTHERN
Broome
Wyndham
Port Hedland
Red
Centre
Great Desert
Tracks South
Central Sheet
Great Desert
Tracks North
West Sheet
Kimberley
Top End & Gulf
Mid West
Western
Australia
Simpson
Desert
Cape
Range NP
Rudall
River NP
Kennedy
Range NP
Kalbarri NP
Cape York Tip
Eastern Australia Tourism Routes Boodjamulla (Lawn Hill) NP
Gregory
NP
Millstream
Chichester NP
Mt Augustus NP
Great Desert Tracks South East Sheet
Great Desert
Tracks South
West Sheet
Darwin •
Mildura
Pilbara
QUEENSLAND
Mackay
Girraween & Sundown Nat Parks
Melbourne
Charleville
Brisbane
Cairns
Townsville
Mt Isa
Rockhampton
Longreach
Alice Springs
Tennant
Creek
Katherine
Halls Creek
Dubbo
KEY TO HEMA REGIONAL MAPS Also includes: Australia map and State maps: Queensland, New South Wales, Northern Territory, South Australia, Victoria, Western Australia, Tasmania
regional key map:regional navigator key 13/5/08 11:38 AM Page 1

Failure to avoid the following
potentially hazardous situations
could result in an accident or
collision resulting in death or
serious injury.
- When installing the unit in a
vehicle, place the unit securely so it
does not obstruct the driver’s view
of the road or interfere with vehicle
operating controls, such as the
steering wheel, foot pedals, or
transmission levers. Do not place in
front of or above any airbag.
- When navigating, carefully
compare information displayed on
the unit to all available navigation
sources, including information
from street signs, visual sightings,
and maps. For safety, always
resolve any discrepancies or
questions before continuing
navigation and defer to posted
road signs.
If these guidelines are not
followed, the internal,
non-user-replaceable,
rechargeable lithium-ion battery
may experience a shortened life
span or may present a risk of
damage to the GPS unit, fire,
chemical burn, electrolyte leak,
and/or injury.
- Always operate the vehicle in a
safe manner. Do not become
distracted by the unit while
driving, and always be fully
aware of all driving conditions.
Minimize the amount of time
spent viewing the unit’s screen
while driving and use voice
prompts when possible. Do not
input destinations, change
settings, or access any functions
requiring prolonged use of the
unit’s controls while driving. Pull
over in a safe and legal manner
before attempting such
operations.
- The unit is designed to provide
route suggestions. It is not
designed to replace the need for
driver attentiveness regarding
road closures or road conditions,
traffic congestions, weather
conditions, or other factors that
may affect safety while driving.
- Do not incinerate.
- Contact your local waste
disposal department to properly
dispose of the unit/battery
- Do not leave the unit exposed
to a heat source or in a high
temperature location, such as in
the sun in an unattended vehicle
on a hot day.To prevent damage,
remove the unit from the vehicle
or store it out of direct sunlight
IMPORTANT SAFETY AND PRODUCT INFORMATION
Battery Warnings

- When storing the unit for a
limited length of time, store within
the following temperature range:
-10˚ to 55˚C.When storing the unit
for an extended time, store within
the following temperature range:
0˚ to 25˚C.
- Do not operate the unit outside
the following temperature range:
-20˚ to 55˚C.
- Do not remove or attempt to
remove the battery.
Important Information
MAP DATA INFORMATION: One of
the goals of the HEMA Navigator is
to provide customers with the
most complete and accurate
cartography that is available to us
at a reasonable cost. Along with
Hema’s extensive field work, we
use a combination of
governmental and private data
sources, which we identify in
product literature and copyright
messages displayed to the
consumer.Virtually all data sources
contain some inaccurate or
incomplete data. In some counties,
complete and accurate map
information is either not available
of is prohibitively expensive.
Declaration of Conformity
Hereby, HEMA Navigator declares
that this product is in compliance
with the essential requirements
and other relevant provisions of
Directive 1999/5/EC.
FCC Compliance
This product has been tested and
found to comply with Part 15 of
the FCC interference limits for
Class B digital devices FOR HOME
OR OFFICE USE.These limits are
designed to provide reasonable
protection against harmful
interference in a residential
installation, and are more
stringent than ‘outdoor’
requirements.
Operation of this device is
subjected to the following
conditions: (1) this device may
not cause harmful interference,
and (2) this device must accept
any interference received,
including interference that may
cause undesired operation.
This product does not contain
any user-serviceable parts.
Repairs should only be made by
an authorized HEMA Navigator
service centre. Unauthorized
repairs or modifications could
result in permanent damage to
the equipment, and void your
warranty and your authority to
operate this device under Part 15
regulations.

This HEMA Navigator product is
warranted to be free from defects in
materials or workmanship for one
year from the date of purchase.
Within this period, HEMA-VMS will, at
its sole option, repair or replace any
components that fail in normal use.
Such repairs or replacement will be
made at no charge to the customer
for parts or labour, provided that the
customer shall be responsible for
any transportation costs.This
warranty does not cover failures due
to abuse, misuse, accident, or
unauthorised alterations or repairs.
Batteries included is warranted for a
period of 12 months from the date of
purchase.
THE WARRANTIES AND REMEDIES
CONTAINED HEREIN ARE EXCLUSIVE
AND IN LIEU OF ALL OTHER
WARRANTIES EXPRESSED, IMPLIED,
OR STATUTORY, INCLUDING ANY
LIABILITY ARISING UNDER ANY
WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR
PURPOSE, STATUTORY OR
OTHERWISE.THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS,WHICH
MAY VARY FROM STATE TO STATE.
IN NO EVENT SHALL HEMA-VMS BE
LIABLE FOR ANY INCIDENTAL,
SPECIAL, INDIRECT, OR
CONSEQUENTIAL DAMAGES,
WHETHER RESULTING FROM THE
USE, MISUSE,
OR INABILITY TO USE THIS PRODUCT
OR FROM DEFECTS IN THE
PRODUCT. Some states do not
allow the exclusion of incidental or
consequential damages, so the
above limitations may not apply
to you.
HEMA-VMS retains the exclusive
right to repair or replace the unit
or software or offer a full refund of
the purchase price at its sole
discretion. SUCH REMEDY SHALL
BE YOUR SOLE AND EXCLUSIVE
REMEDY FOR ANY BREACH OF
WARRANTY. To obtain warranty
service, contact your local Hema
Navigator dealer or call HEMA VMS
product support for shipping
instructions and RA tracking
number. Securely pack the unit
and a copy of the original sales
receipt, which is required as the
proof of purchase for warranty
repairs.Write the RA (Returns
Authorisation) tracking number
clearly on the outside of the
package. Send the unit, freight
charges prepaid to any HEMA
Navigator service centre.
Online Auction Purchases:
Products sold through online
auctions are not eligible for
rebates or other special offers
from HEMA VMS. Online auction
confirmations are not accepted for
warranty verification. To obtain
warranty service, an
Limited Warranty

original or copy of the sales receipt
from the original retailer is
required. HEMA VMS will not
replace missing components from
any package purchased through
an online auction.
INTERNATIONAL PURCHASES: A
separate warranty is provided by
international distributors for units
purchased outside of Australia &
New Zealand. This warranty is
provided by the local in-country
distributor and this distributor
provides local service for your unit.
Distributor warranties are only
valid in the area of intended
distribution. Units purchased in
Australia or New Zealand must be
returned to the HEMA Navigator
service centre in Australia.
Your HEMA navigator contains
sensitive electronic components
that can be permanently damaged
if exposed to excessive shock or
vibration.To minimize the risk of
damage to your navigator, avoid
dropping your unit and operating
it in high-shock and high-vibration
environments.
- Do not store the Navigator where
prolonged exposure to extreme
temperatures can occur, because it
can cause permanent damage.
- Do not expose the Navigator to
water. Contact with water can
cause this unit to malfunction.
- Never use a hard or sharp
object to operate the
touchscreen or damage may
result.
CLEANING THE UNIT
The Navigator is constructed of
high-quality materials and does
not require user maintenance
other than cleaning. Clean the
unit’s outer casing (not the
touchscreen) using a cloth
dampened with a mild detergent
solution, and then wipe dry.
Avoid chemical cleaners and
solvents that can damage plastic
components.
CLEANING THE TOUCH SCREEN
Clean the touch screen with a
soft, clean, lint-free cloth. Use
water, isopropyl alcohol, or
eyeglass cleaner, if needed. Apply
the liquid to the cloth, and then
gently wipe the touch screen.
AVOIDING THEFT
- To avoid theft, remove the
Navigator and mount from sight
when not in use. Remove the
residue on the windscreen left by
the suction cup.
CARING FOR YOUR NAVIGATOR