Herdio HWA16BT User manual

Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC Requirement ：
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 20cm between the radiator & your body. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Line level audio is typically supplied via the front 3.5mm input jack
pigtail leads located on the rear of the amplifier receiver wall plate
(for-wired speaker connecton).*Please note: The unit may cease to
functon, or function irregularly,if more than one audio source is
2

connected totheunit.Ensure only a single audio source is connected
at a tmeto allow for optimum performance and functonality;
Can be Hard-Wired or Powered via Included Power
In-Wall Audio Control Receiver with Built- in Amplifier
Microphone Paging and Speaker Control Made Easy
BT Wireless Music function allows you connect & Stream
AUX input port plug & play Smartphones and other music
devices Speaker Terminal Block, Connect up to (2) Speakers
Universal Gang Box / Wall Plate Standard Size, can be Hard-
Wired or Powered via Power Adapter Perfect for Home/Office
Applicacations
3
Controller Receives & Directs Bluetooth Wireless Audio Works
with All of Your Favorite Devices: (Smartphones,MP3
Players, Tablets, Laptops, Computers, etc.)
Bluetooth Network Name: 'Herdio ' (No Password Required)
Wireless Range: 30' Feet (10 Meters)
Power Output 100 Walt Peak, 40 Watt RMS x 2 Ch.@ 4 Ohm
Bluetooth Version: 5.0
Mic Input Type: Dynamic
Power, Amp Type: Stereo Class-D
Minimum Load Resistance: 4 Ohm
T.H.D.: 0.03% (8 Ohm, 1 kHz)
Power Draw: 12V 3Amps
Power: DC 100-240V, 50/60Hz(12V DC Adapter)

The In-Wall Amplifier has built-in Bluetooth receiver ability
allowing you to wirelessly stream audio to your connected
speaker system.Follow these steps to get connected:
Make sure the unit is properly connected to external speakers.
Make sure the unit is properly connected to a power source.
1. Before attempt ing to pair / connect, ensure the unit is
in 'Bluetooth Mode'. Enter 'Bluetooth Mode' by selectng
'BT'on the unit's front panel Input Selector.
2. Press and Hold the Volume Knob for more than 3 Seconds
to POWER the Unit ON/OFF.
3. Then, go to your Smart device's Bluetooth Network
Settings and connect to the Wall Plate. The Network
Name will appear as 'Herdio' on your device list. No
password is required to connect but if you are
prompted enter '0000' (4 zeroes).
4. Upon pairing, the Bluetooth LED indicator light will
blink progressively quicker untl the unit successfully
pairs with a compatible Bluetooth device.
5. When a successful Bluetooth connecton is established
the Bluetooth L ED indicator light will shine solid and
indicatng that the unit is ready to transmit audio.
4
:

1. PWR: Power LED. Press and Hold the volume knob for more
than 3 Seconds to POWER the Unit ON/OFF.
2.INPUT SELECTION: Audio Input between AUX/B T/MIC
3.USB PORT: USB Card Reader&USB Charge(5V 1A)
4.DC 12V IN: 12V DC Power Supply
5.BT: Bluetooth Signal LED
6.VOL UME/ON/OFF: Master Volume Control with Power ON/OFF
7.MIC IN: 1/4 Microphone Input Connector Jack
8.AUX IN: (3.5mm)Audio Input Jack can Connect&Instantly
Stream Audio From your Favorite Devices.
5

Under normal circumstances, power is connected to the front
panel power input via the included AC adapter.Power may be
supplised from an alternatve 12V DC power source via the rear
pigtail RED+ /BL .ACKS leads (for hard-wired installatons ).
When an AC adapter powers the unit, via the front panel power
input, the RED+ lead is disconnected.
This product occupies standard single gang device space and is
compatble with most deep sized electrical boxes or low voltage
bracket systems.*Please note: minor fitting adjustments may be
necessary for mountng the wall plate amplifier receiver in certain
wall installaton Applications.
6