HEX-BEAM SP7IDX MARK III HD User manual

HEX –BEAM SP7IDX TECHNOLOGY
1
HEXBEAM MARK III HD &
HEXBEAM MARK III Light
Ver 05.018
HEX-BEAM SP7IDX TECHNOLOGY ANTENNA is a broad band hex
antenna operating in PLUG AND PLAY system, its assembly time is 1-1,5h for
one person. Its installation doesn't require any additional tuning. Thanks to
its small and compact structure its turning requires only a small light rotor.
The antenna works properly even when it's installed relatively low over the
ground.
Both antennas are equipped with all parts, required for a one, five or
six bands beam in range from 6 to 20 meters. The HEXBEAM SP7IDX
TECHNOLOGY offers mounted on the ground gain for front –to –back huge
amplify. The antenna offers the same values as a full size YAGA antenna. Has
unique shape: is much smaller, stiffly and makes less noise than typical
beams, it is lighter, easier to montage.
Please see its possible assembly methods on:
http://sp7idx-hexbeam.eu/hexbeam/mounting-suggestion
The antennas are tested at 7,3m height with analyser RigExpert AA-
55 ZOOM + MetroVNA Pro Touch Deluxe
24,8 m AIRCELL 7 + RG400/U HEW-Kabel GmbH Germany Filial Nordic-
Örebro-Cable
Test connections conducted with transceiver Flex Radio System
6600M + Electraft K-3s
PA Team SPE EXPERT 1,3K + 2K
It is helpful if you completely read through the instructions a couple of time before
you start.
The antenna is assembled intuitively, but please READ the manual carefully.
Please pay special attention to the red inscriptions.

2
Parcel Arrived

HEX –BEAM SP7IDX TECHNOLOGY
3
PART LIST
Three types of spreders (poles)
6 pieces - small ones + kevlar lines with S-hooks (6x 1m diameter 12,7mm) #4/8
6 pieces - medium (6x 1,35m diameter 17mm) #5/8
6 pieces - large (6x 1,35m diameter 22mm) #6/8

4
Set of hol dres (wire cleat set):
Size 5 - 6 set
Size 7 - 24 set
Size 9 - 6 set
STORE + Insulating tape - 1 piece –(option) #2/8
Screw 8 x 20 - 4 pieces for hub clamp on rure with centerpost

HEX –BEAM SP7IDX TECHNOLOGY
5

6
Down centerhub - mast

HEX –BEAM SP7IDX TECHNOLOGY
7

8
6 sets of electric component (driven+reflector+spacer cords)
6-10-12-15-17-20m
#2/8

HEX –BEAM SP7IDX TECHNOLOGY
9
Center post + balun (option) -1set
#3/8

10
do not change the position of the screw and do not tighten it !!!

HEX –BEAM SP7IDX TECHNOLOGY
11
Normal situation centerpost
Center plate-1set
#1/8
# 7/8 ( or 8/8) polyamide element block clamps 6 set

12
#8/8 (or 7/8) sleeve 6 art

HEX –BEAM SP7IDX TECHNOLOGY
13

14
Centerhub complet +centerpost

HEX –BEAM SP7IDX TECHNOLOGY
15
bottom part centerhub

16

HEX –BEAM SP7IDX TECHNOLOGY
17
ASSEMBYL INSTRUCTION
Step 1.
Fix holders on spreaders with 2, 3, 4, 5 and 6 symbols so that they look like on spreaders
no.1
6 small poles (1m - 12,7mm) + holders no. 5 - 1 piece per pole
6 medium poles (1,4m - 17mm) + holders no. 7 - 4 pieces per pole
6 large poles (1,5m - 22mm) + holders no.9 - 1 piece per pole
NO MAX !!!

18
Attention !
correct wire tension adjust with black handle fixing left or right,
Do not tighten the wire too much, The wires should be a little slack
do not screw it tightly, not the wheel from the car !!!
Only minor adjustment is required if any, for proper tension of the wires.
Not to tight, not to much sag of the wires. After all we must realize
that my measurements are estimates too.
Typical placement of Wire Guide Clamps

HEX –BEAM SP7IDX TECHNOLOGY
19

20
Attention
correct wire tension adjust with black handle fixing left or right,
Do not tighten the wire too much, do not screw it tightly, not the wheel
from the car !!!