Hitachi CMP307XE User manual

Plasma Display
Se
p
tember 2001 Di
g
ital Media S
y
stems Division


SERVICE MANUAL (Rev.D)
ＲＧＢ/ ＶＩＤＥ Ｏ ＭＥＮＵ ＳＥＬＥＣＴ ＶＯＬＵＭＥ
ＳＴＡＮＤＢＹ（Ｒ ＥＤ）
ＯＮ （ ＧＲＮ）
ＨＩＴＡＣＨＩ
Be sure to read this manual before servicing. To assure safety from fire, electric shock, injury,
harmful radiation and materials, various measures are provided in this Hitachi Plasma display.
Be sure to read cautionary items described in the manual to maintain safety before servicing.
1. Since Panel Module and front Filter are made of glass, handling to the broken Module and
Filter shall be taken care sufficiently in order not to be injured.
2. Replacing work shall be started after the Panel Module and the AC/DC Power supply
become sufficiently cool.
3. Special care shall be taken to the display area in order not to damage its surface.
4. The Panel Module shall not to be touched with bare hand to protect its surface from stains.
5. It recommended to use clean soft gloves during the replacing work in order to protect not
only the display area of the Panel Module but also a serviceman himself.
6. The Chip Tube of Panel Module (located upper left of the back) and flexible cables
connecting Panel glasses to drive circuit PWBs are very weak, so shall be taken care
sufficiently not break. If you break Chip Tube, the Panel doesn’t display forever.
1. Features 2
2. Specifications 2
3. Names of each part. 3
4. Trouble shooting 4
5. Block diagram 6
6. Disassembly diagram 7
7. Re-Adjustment 11
8. Replacement Parts list 14
SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT.
SM0059
CMP307XE
CMP307XU
Caution
Contents
Serviceman Warning


1. Features
z 37 inches XGA high-definition color plasma display panel
z Newly developed Multi-scanning converter provides a multiscan coverage of TV signals
through to PC analog signals (24kHz to SXGA(64kHz))
z Large high-quality display images free from color misconvergence and display distortion,
as well as from geomagnetic effect and the magnetic effect of ambient power lines
2. Specifications
PDP Module 37 inches XGA PDP panel (aspect ratio 4:3)
Description FPF37C12896UA
Pixel pitch 0.735 mm(H) x 0.735 mm(V)
Pixel structure RGB striped
Brightness 150cd/m2(typical) with front filter
Contrast 400:1 (typical) in dark room
RGB 1
(mD-15p)
RGB 2
(BNCx5)
Video : 0.7 Vp-p
Sync. : Separate H/V, TTL level
CompositeH/V,TTLlevel
Sync. on Green at 0.30 Vp-p
Video 1
(RCA Pinx1,
S-terminalx1)
Composite Video or S-video (for S2)
NTSC3.58
Video : Composite 1.0 V
S-video Y: 1.0 Vp-p, C:0.29Vp-p
Sync. : Composite sync
Input
Signal
Video 2
(RCA Pinx3)
Component Video
Y,Pb,Pr or Y,Cb,Cr: (480i,480P,1080i,1035i)
Video : Y : 1.0 Vp-p
Pb/Cb,Pr/Pr:0.7Vp-p
Sync. : Superimposed with Y signals
Colors 2.09 million
Synchronization Horizontal : 24 – 64 kHz
Vertical : 50 - 75 Hz
Resolution Horizontal : 1024 dots (max.)
Vertical : 768 lines (max.)
Viewable Image Size 37 inches (940 mm), diagonal (typical)
Viewable Image Area Horizontal : 753 mm (typical)
Vertical : 564 mm (typical)
Color Temperature NORM(9300 K)
Warm-up Time 30 minutes to reach optimum performance level.
Power Supply AC 100 - 120 / 200 - 240 V (4.3A /2.2A)
50/60 Hz
(automatically selected)
Power Consumption : 390 W (typical)
(provided with power save circuit.)
Dimensions 884 (W) x 684 (H) x 99.7 (D) mm (without stand)
884 (W) x 766 (H) x 300 (D) mm (with stand)
Weight 29.8 kg (approx.) without stand
32.8 kg (approx.) with stand
Environmental
Condition Operation Storage
Temperature 5ºC to 35ºC 0ºC to 50ºC
Humidity 20% to 80% 20% to 80%
2


3. Names of each part
z
Outlook














z
Input terminal(D-sub connector)
Pin No. Signal
1 Red Video
2 Green Video (Sync. optional)
3 Blue Video
4 No connection
5 No connection
6 Red Ground
7 Green Ground
8 Blue Ground
9 No connection
10 Ground
11 No connection
12 SDA
13 H.Sync. (or H/V composite)
14 V.Sync.
15 SCL
Message table
☛Onscreen display
Indication Condition
The monitor indicates the
message
“POWER SAVE”.
The monitor detects no
sync. signal.
The monitor indicates the
message
“OUT OF FREQUENCY”.
The monitor detects a
sync. signal which is out
of specification, or
unstable.
3

ＲＧＢ/ＶＩＤ ＥＯ ＭＥＮＵ ＳＥＬＥＣＴ ＶＯＬ ＵＭＥ
ＳＴＡＮＤＢＹ（ＲＥＤ）
ＯＮ （ＧＲＮ）
ＨＩＴＡＣＨＩ
ＦＲＯＮＴ ＶＩＥＷ
Ｆｒｏｎｔ
Ｆｒａｍｅ
Ｐｏｗｅｒ
Ｓｗｉｔｃｈ
Ｃｏｎｔｒｏｌ
Ｓｗｉｔｃｈｅｓ
ＳＴＡＮＤ
Ｆｒｏｎｔ
Ｆｉｌｔｅｒ
LISTED
7J88
UL1950
WAR N IN G/ AV ER TIS SE ME NT /V O RS IC HT/ PR EC AU CI ON
S/N
JUNE/JUIN1999
Y9G000001
CMP402HD
100‑120V/220‑240V〜
50‑60Hz,5A/2.5A
USC
2
PLASMADISPLAY/ECR ANAPLASMA
MOD.NO./MOD.N.
o
必ずア−ス接続を行って下さい。
（ＭＯＮＯ）
ＬＲ
ＶＨＢＧＲ ＲＧＢ１ 〔Ｄ−ＳＵＢ〕
ＲＧＢ２〔ＢＮＣ〕
ＲＧＢ ＩＮＰＵＴ
ＡＵＤＩＯ
ＱＬ０９００１
ＲＳ２３２ＣＩＮ
ＲＥＡＲ ＶＩＥＷ
Ｒｅａｒ
Ｃｏｖｅｒ
ＡＣ ｉｎｌｅｔ
ＭＡＩＮ ＳＷＩＴＣＨ
ＶＩＤＥＯ２ ＩＮＰ ＵＴ
ＲＬＲＢ Ｙ
ＡＵＤＩ Ｏ
（ＭＯＮＯ）
Ｂ
〔ＣＯＭＰＯＮＥＮＴ〕
Ｒ
Ｐ ／Ｃ Ｐ ／Ｃ
ＲＬ
ＶＩＤＥＯ Ｓ− ＶＩＤＥＯ
ＶＩＤＥＯ１ ＩＮＰＵＴ
（ＭＯＮＯ）
ＡＵＤＩＯ
ＲＧＢ ｉｎｐｕｔ Ｔｅｍｉｎａｌｓ
Ｖｉｄｅｏｉｎｐｕｔ Ｔｅｍｉｎａｌｓ

Front
Filter
Front
Frame
Power
Switch
FRONT VIEW Control
Switch
STAND
(Option)
Rear
Cover
RGB input terminals
Video in
p
ut terminals
REAR VIEW
AC inlet
MAIN SWITCH


Yes

Yes

4. Trouble shooting
Are
Voltage
applied to pins7,11(PSD3)
of the Signal PWB ?

Signal PWB

Speaker
Power can not be turned on (LED is not light)

Is the input voltage
applied to the AC/DC
Power unit ?
(PESW1 4, 6)

No

Yes

AC inlet

Power switch AC Fuse
F911 10A250V

7 : +5.6V
11 : +4.4V
9 : GND
AC/DC
Power unit

No

Yes

Picture is dis
p
la
y
ed. But no sound
Are
Voltage
applied to pins 4(PSD3)
of the Signal PWB ?
No

AC/DC
Power unit

4 : 14V
5 : GND
No

Are
there signals on
Speaker ?
Signal PWB

4


No

No

red

Yes

high (5V)

low (0V)
Yes
No

No

green

Yes
Yes
1 : +180V
4 : GNDNo 
9 : GND
11 : +4V

Yes

5 : GND
7 : +5.6V

Yes

See page 6

Is Voltage
of the pin 2(PSC1)
on the Signal PWB
high?
Is the LED red
or green?
Picture is not dis
p
la
y
ed
(
LED is li
g
htin
g)
No

AC/DC
Power unit

Signal PWB

AC/DC
Power unit

Do the Fans
rotate?
When
disconnect
PF1-3 of the AC/DC
Power unit, the picture
Is displayed ?
DC Fan

AC/DC
Power unit

Is Voltage
of the pin 5(PED)
on the AC/DC Power
unit 5V AC/DC
Power unit

Are Voltages
of the pin 1(PEY1)
on the AC/DC Power
unit collect ?
Is Voltage
of the pin 9, 11(PED)
on the AC/DC Power
unit collect ?
Panel
Module

Panel Module

AC/DC
Power unit

Are
Voltage
applied to pins 7(PED)
of the Signal PWB?

5

PAY4
PAY4
PAY3
PAY3
PED
PED
EEF6
ESV1
ESV2
ESV3
PSD1
PSD1
PEY PEY
1
PXY
1
PXY
2
PX08PX07
PX05 PX06
PXY
2
PXY
1
Y
UP
Y
DW
DC-DC
Y_SCAN
X_SCAN
SIGNAL DIGITAL VIDEO
AC-DC POWER
ADDRESS UP/RI
PESW1
ADDRESS UL/LF
X
DW
X
UP
ADDRESS DW/RI
A
DDRESS
DW/LF
AC
INLET
USPL
SP
USPR
POWER SW
CONTROL
LED
PSC2
MFN3 MFN2 MFN1
1
1
1
1
45
45
1
45
1 45
1
40 40
140
1
PAX2
PAX1
40
40 1
1
40 40
4
1
8
6
1
1
1
1
1
1
12
12
1
1
1
1
1
11
1
1
1
12
12 1
1
8
1
7
7
1
1
13
19
11
1
7
7
5
55
5
33
PSS
1
45
45
1
PY01 PY03
PY02
PY04
45
1 45
40
1
40
1
40
1
1
1
1
1
13
19
11
40 1
40 1
1 40
1
11
5
55
1
5
5
5
PDY PDY PDY PDY PDY PDY
PDX PDX PDX PDX PDX PDX
40
1
40
1
40
1
40
1
40
1
40
1
40
1
40
1
40
1
180v
VADR(70V),+5V
VADR(70V),+14V,,+5V
VSUS(180V)
VXSC(60V)
VRES(340V)
VADR(70V)
VXSC(60V)
VRES(340V)
VYSC(70V)
VYSB(-170V)
+14V
+5V
4V,5.6V.14V,
STB-5V
4V,5.6V.14V
4V,5.6V.14V
SW.REG.
SW.REG.
5V,VADR(70V)
5. BLOCK DIAGRAM
6
40 1
40 1
PAX5

PAX6
PST
PAY1 PAY2
PAY1 PAY2
PSD3
PSD3
PST PSD2
PSD2
PSC1
PSC2
PAX4
PAX8
PAX7 PAX3
PSC1


6. Disassembly diagram
(1) Remove Back Cover
Be careful not to be damaged the face
of Front Filter. Remove 4 screws(a) and
remove the Rear stand.
Remove 20 screws(b) ､and remove
Back Cover.
At this time be careful not to be
damaged edges of Back Cover and its
coated face.
7

LISTED
7J88
UL1950
WARNING/AVERTISSEMENT/VORSICHT/PRECAUCION
S/N
JUNE/JUIN1999
Y9G000001
CMP402HD
100‑120V/220‑240V〜
50‑60Hz,5A/2.5A
USC
2
PLASMADISPLAY/ECRANAPLASMA
MOD.NO./MOD.N.
o
必ずア−ス接続を行って下さい。
（ＭＯＮＯ）
ＬＲ
ＶＨＢ ＧＲ ＲＧＢ １ 〔Ｄ−ＳＵＢ〕
ＲＧＢ２〔ＢＮＣ〕
ＲＧＢ ＩＮＰＵＴ
ＡＵＤＩＯ
ＱＬ０９００１
ＲＳ２３２ＣＩＮ
Ｓｃｒｅｗ（ａ）
ＶＩＤＥＯ２ＩＮＰＵＴ
ＲＬＲＢ Ｙ
ＡＵＤＩＯ
（ＭＯＮＯ）
Ｂ
〔ＣＯＭＰＯＮＥＮＴ〕
Ｒ
Ｐ ／Ｃ Ｐ ／Ｃ
ＲＬ
ＶＩＤＥＯ Ｓ−ＶＩＤＥＯ
ＶＩＤＥＯ１ ＩＮＰＵＴ
（ＭＯＮＯ）
ＡＵＤＩＯ

Screw(a)

ＱＬ０９００１
ＲＳ２３２ＣＩＮ（ＭＯＮＯ）
ＬＲ
ＶＨＢＧＲ ＲＧＢ１ 〔Ｄ−ＳＵＢ〕
ＲＧＢ２〔ＢＮＣ〕
ＲＧＢ ＩＮＰＵＴ
ＡＵＤＩＯ
Ｓｃｒｅｗ（ｂ）
Ｓｃｒｅｗ（ｂ） Ｓｃｒｅｗ（ｂ）
Ｓｃｒｅｗ（ｂ）
Ｓｃｒｅｗ（ｂ） Ｓｃｒｅｗ（ｂ）
ＶＩＤＥＯ２ＩＮＰＵＴ
ＲＬＲＢ Ｙ
ＡＵＤＩＯ
（ＭＯＮＯ）
Ｂ
〔ＣＯＭＰＯＮＥＮＴ〕
Ｒ
Ｐ ／Ｃ Ｐ ／Ｃ
ＲＬ
ＶＩＤＥＯ Ｓ−ＶＩＤＥＯ
ＶＩＤＥＯ１ ＩＮＰＵＴ
（ＭＯＮＯ）
ＡＵＤＩＯ

Screw(b)
Screw
(
b
)
Screw(b)
Screw(b)
Screw(b) Screw(b)


(2) Remove Signal PWB
Disconnect
ESC1(PH-3P), ESC2(PH-7P),
ESS(EH4P-HR3P/HR2P),
ESD3(EH-12P), ESD2(FFC-40P) ,
PSD1(FFC-40P)
PST ,ESV3,EVC2, EVC1
connectors.
Be careful not to be damaged the
PSV1-3 Connector holder.
Remove 2 screws(c), 8screws(f),
plastic rivet, 4screws(e) 2screws(g)
and remove Signal PWB,and
Video PWB.
(3) Remove filter PWB
Disconnect P902A, PESW1 connector.
Remove 4screws(d) and remove
the filter cover.
Then remove 4screws(g),
and remove Filter PWB.
8

ＳＩＧＮＡＬ
ＰＷＢ ＶＩＤＥＯ ＰＷＢ
Ｓｃｒｅｗ（ｃ） Ｓｃｒｅｗ（
Screw(c) Screw(c)
Ｓｃｒｅｗ（ｆ）
Ｐｌａｓｔｉｃ ｒｉｖｅｔ
Ｓｃｒｅｗ（ｇ）
Ｓｃｒｅｗ（ｅ）
Ｓｃｒｅｗ（ｅ）
Ｓｃｒｅｗ（ｆ）

Screw (e)
Screw (e)
Screw (g)
Plastic rivet
Screw (f)
Screw (f)
Ｓｃｒｅｗ（ｄ）
Ｓｃｒｅｗ（ｇ）
Ｆｉｌｔｅｒ
Ｃｏｖｅｒ

Filter Cover Screw (d)
Screw (g)


(4) Remove Front Frame
Remove 3 screws(l),then be
careful not to be damaged the
face of front filter.
Attached the Stand with 4screw(a),
then stand it vertically.
When remove front frame.
(5) Remove Front Filter(Glass)
Remove 22 screws(m), and remove
Filter hold Metal and Front Filter.
Be careful not to fall down the front
Filter. When remove the filter hold
Metal. When attach the new Front
Filter, remove protection film on a
side(yellow tag is marked).Then
attach to the Front Frame, locating the
conducting electrode side to the inside,
and attach Filter hold Metal.
Ｓｃｒｅｗ（ｍ） Ｓｃｒｅｗ（ｍ）
Ｓｃｒｅｗ（ｍ） Ｓｃｒｅｗ（ｍ）Ｍａｉｎ ｆｒａｍｅ
Ｓｃｒｅｗ（ｍ） Ｓｃｒｅｗ（ｍ）
Ｆｒｏｎｔ Ｆｉｌｔｅｒ（Ｇｌａｓｓ）

Screw(m)

Screw(m)
Front Filter (Glass)
Screw
(
m
)
Screw
(
m
)
Screw(m)
Screw(m)
Filter holder
metal
9
Ｓｃｒｅｗ（ｌ）
ＦｒｏｎｔＦｒａｍｅ
Ｓｃｒｅｗ（ａ）

Screw (ｌ)
Front Frame
Screw (ａ)


(6) Remove Fan
Remove 3screws(k),and
disconnect AEF6orBEF6
connector,
Remove Fan hold Metal.
Then remove 2plastic rivets.
(7) Remove AC/DC Power unit
Remove 4 screws(o) and 2 screw(p),
then disconnect
PESW1(VH-6P),
PEY1(VH-5P),
PED(EH-12P),
PF1(EH-3P),
PF2(EH-3P),
PF3(EH-3P)
connectors.
10

Ｐｒａｓｔｉｃ ｒｉｖｅｔ
Ｆａｎ Ｍｅｔａｌ
Ｓｃｒｅｗ（ｋ）
AEF6/BEF6
ｃｏｎｎｅｃｔｏｒ
Plastic rivet
AEF6/BEF6
Connector
Screw (ｋ)
Ｆａｎ Ｍｅｔａｌ

Ｓｃｒｅｗ（ｏ） Ｓｃｒｅｗ（ｐ）

Screw (o) Screw (p)
Fan Metal


7. Re-Adjustment
After changing the Signal PWB or Panel Module, re-adjustment is needed according to the
item 7.1 to 7.5 For Video PWB, item 7.3 to 7.5 are needed.
7.1 Personal Computer (PC)input black level/fundamental amplitude adjustment
How to Prepare
1.Connect RGB input terminal XGA(Vertical Sync Frequency 60Hz),0.7Vpeak,no -set up.
2.Appear and Adjust screen OSD Menu of Picture:
Contrast:127 Brightness:0, Color Select :MID, Video level :0.7V.
How to Adjust
1.Set Service Adjustment Mode and adjust as follows by Remote Control Transmitter
(7.5 Refer How to set to Service Adjustment Mode)
2.Set Adjustment No.35,36 ,and 37 scale to 255
3.Input full black level Signal
4.Set Adjustment No.41 to changing point from black to Red(set to black point)
5.Set Adjustment No.42 to changing point from black to Green(set to black point)
6.Set Adjustment No.43 to changing point from black to Blue(set to black point)
7.Input all white level Signal
8.Set Adjustment No.44 to changing point from Red to black(set to black point)
9.Set Adjustment No.45 to changing point from Green to black(set to black point)
10.Set Adjustment No.46 to changing point from Blue to black(set to black point)
Tolerances of each color adjustment numbers are less than 10, if more than 10,
Re-adjust from above 2 steps.
7.2 PC color temperature adjustment
How to prepare
1.Connect RGB input terminal XGA(Vertical Sync Frequency 60Hz),0.7Vpeak, without set
up signal.
2.Window color (R,G and B)should be 255 each.
and input white window(33%) Signal.
2.Appear and Adjust screen OSD Menu of Picture:
Contrast:127, Brightness:0,GAMMA:2.2,Video level:0.7V
How to Adjust
1.Set Service Adjustment Mode and adjust as follows by Remote Control Transmitter.
2.Mesurement probe of CRT Color Analyzer CA-100 is set on the center of screen.
(Center of white window signal)
11



3.Adjust color temperature as follows by increasing or reducing numbers of NO.32,33,34.
PC color temperature (COOL)
x=0.277±
±±
±0.002, ｙ
ｙｙ
ｙ=0.289±
±±
±0.002 at 10400K
4.Adjust color temperature as follows by increasing or reducing numbers of NO.35,36,37.
PC color temperature (NORM)
x=0.283±
±±
±0.002, y=0.298±
±±
±0.002 at 9300K
5.Adjust color temperature as follows by increasing or reducing numbers of NO.38,39,40.
PC color temperature (WARM)
x=0.313±
±±
±0.002, y=0.329±
±±
±0.002 at 6500K
Suggestion
1.Luminance of panel surface is less than 20lux to arrange adjustment environment
2.Color select mode is automatically set to COOL while adjustmentNo.32,33 and 34.
3.Color select mode is automatically set to NORM while adjustmentNo.35,36 and 37.
4.Color select mode is automatically set to WARM while adjustmentNo.38,39 and 40.
7.3 Video input black level/fundamental amplitude adjustment
How to Prepare
1.Connect Video input ( NTSC 3.58),
Video level 0.714Vp-p, Sync level 0.286Vp-p, no set up
2.Appear and Adjust screen OSD Menu of Picture:
Contrast: 127 Brightness:0, Video level: NORMAL, Color Select: MID
How to Adjust
1.Set Service Adjust Mode and adjust as follows by Remote Control Transmitter
2.Set Adjustment No.35,36, and 37 scale to 255
3.Input all black level Signal
4.Set Adjustment No.41 to changing point from black to Red(set to black point)
5.Set Adjustment No.42 to changing point from black to Green(set to black point)
6.Set Adjustment No.43 to changing point from black to Blue(set to black point)
7.Input all white level Signal
8.Set Adjustment No.44 to changing point from Red to black(set to black point)
9.Set Adjustment No.45 to changing point from Green to black(set to black point)
10.Set Adjustment No.46 to changing point from Blue to black(set to black point)
Tolerances of each color adjustment numbers are less than 20, if more than 20,
Re-adjust from above 2 steps.
12



7.4 Video color temperature adjustment
How to prepare
1.Connect Video input ( NTSC 3.58),
Video level 0.714Vp-p ,Sync level 0.286Vp-p,no -set up
2.Input white window(33%) Signal.
2.Appear and Adjust screen OSD Menu of Picture:
Contrast:127 ,Brightness:0,Video level:NORMAL,GAMMA:2.2
How to Adjust
1.Set Service Adjust Mode and adjust as follows by Remote Control Transmitter.
2.Mesurement probe of CRT Color Analyzer CA-100 is set on the center of screen.
(Center of white window signal)
3.Adjust color temperature as follows by increasing or reducing numbers of NO.32,33,34.
Video color temperature (COOL)
x=0.269±
±±
±0.002, y=0.266±
±±
±0.002 at 14100K
4.Adjust color temperature as follows by increasing or reducing numbers of NO.35,36,37.
Video color temperature (NORM)
x=0.287±
±±
±0.002, y=0.287±
±±
±0.002 at 9400K
5.Adjust color temperature as follows by increasing or reducing numbers of NO.38,39,40.
Video color temperature (WARM)
x=0.314±
±±
±0.002, y=0.315±
±±
±0.002 at 6500K
Suggestion
1.Luminance of panel surface is less than 20lux to arrange adjustment environment
2.Color select mode is automatically set to COOL while adjustmentNo.32,33 and 34.
3.Color select mode is automatically set to NORM while adjustmentNo.35,36 and 37.
4.Color select mode is automatically set to WARM while adjustmentNo.38,39 and 40.
7.5 How to set to Service Adjustment Mode
Turn off the sub power button( or power button on the Remote Control Transmitter)
then pushing RGB/VIDEO and SELECT buttons located on the bottom of the set
and turn on the sub power button until “Service Adj. Mode” OSD is appeared( more than
5 seconds)
When fall out from Service Adjust Mode, turn off the sub power button( or power button
on the Remote Control Transmitter).

13


THE UPDATED PARTS LIST
FOR THIS MODEL IS
AVAILABLE ON ESTA

Hitachi, Ltd. Tokyo, Japan
International Sales Division
THE HITACHI ATAGO BUILDING,
No. 15 –12 Nishi Shinbashi, 2 –Chome,
Minato –Ku, Tokyo 105-8430, Japan.
Tel: [phone]
HITACHI EUROPE LTD,
Whitebrook Park
Lower Cookham Road
Maidenhead
Berkshire
SL6 8YA
UNITED KINGDOM
Tel: [phone]
Fax: [phone]
Email: [e-mail]
HITACHI EUROPE S.A.
364 Kifissias Ave. & 1, Delfon Str.
152 33 Chalandri
Athens
GREECE
Tel: [phone]
Fax: [phone]
Email:[e-mail]
HITACHI EUROPE GmbH
Munich Office
Dornacher Strasse 3
D-85622 Feldkirchen bei München
GERMANY
Tel: [phone]
Fax: [phone]
Hotline: [phone] (12ct/min)
Email: [e-mail]
HITACHI EUROPE S.A.
Gran Via Carlos III, 101-1
08028 Barcelona
SPAIN
Tel: [phone]
Fax: [phone]
Email: [e-mail]
HITACHI EUROPE srl
Via Tommaso Gulli N.39, 20147
Milano, Italia
ITALY
Tel: [phone]
Tel: [phone] Servizio Clienti
Fax: [phone]
Email: [e-mail]
HITACHI Europe AB
Box 77 S-164 94 Kista
SWEDEN
Tel: [phone]
Fax: [phone]
Email: [e-mail]
HITACHI EUROPE S.A.S
Lyon Office
B.P. 45, 69671 BRON CEDEX
FRANCE
Tel: [phone]
Fax: [phone]
Email: [e-mail]
HITACHI EUROPE LTD (Norway) AB
STRANDVEIEN 18
1366 Lysaker
NORWAY
Tel: [phone]
Fax: [phone]
Email: [e-mail]
HITACH EUROPE AB
Egebækgård
Egebækvej 98
DK-2850 Nærum
DENMARK
Tel: [phone]
Fax: [phone]
Email: [e-mail]
HITACHI EUROPE AB
Neopoli / Niemenkatu 73
FIN-15140 Lahti
FINLAND
Tel : [phone]
Fax: [phone]
Email: [e-mail]
Hitachi Europe Ltd
Bergensesteenweg 421
1600 Sint-Pieters-Leeuw
BELGIUM
Tel: [phone]
Fax: [phone]
Email:[e-mail]
HITACHI EUROPE LTD
Na Sychrove 975/8
101 27 Praha 10 –Bohdalec
CZECH REPUBLIC
Tel: [phone]
Fax: [phone]
Email:[e-mail]
www.hitachidigitalmedia.com