Hitachi CP-X940E User manual

-1 About Trademarks I
●VGA and XGA are trademarks of IBM (International Business Machines Corporation).
●Macintosh is registered trademark of Apple Computer Corporation of the U.S.
●VESA and SVGA are trademarks or registered trademarks of Video Electronics Standards association.
QWindows95 and Windows98 are registered trademarks of Microsoft Corporation in the U.S. and other countries.
Carefully observe the trademarks and registered trademarks of all companies, even when not mentioned.
2

[Safety precaution]
■If any abnormality occurs.
●When there is an abnormal smell or smoke, if
you use this unit as it is, this could cause afire
or electric shock, etc. When an abnormality is
found, immediately turn off the power switch
and pull out the power plug horn the power
outlet. Check that there is no smoke, etc., then
contact your dealer to repair the unit. Do not
repair it yourself as it is very dangerous.
●Do not use this unit as it is after
trouble has occurred,
such as “No picture”, “No
sound, “Abnormal Ae
sound’, etc. This may cause afwe, Pull out the
power plug
electric shock, etc. In this case from the
immediately turn off the power power
outlet.
switch and disconnect the power
plug, then contact your dealer to repair the
unit.
●If water, etc. enters inside the unit, turn off the
power switch of the unit first and discomect
the power plug and then contact your dealer.
If you use it as it is, it may cause afire, electric
shock, etc.
■Do not install this unit in an unstable place.
Avoid placing it in an unstable place
such as weak base, inclined floor, etc. m
resulting in injury.
Do not open the cabinet.
Do not open the cabinet.
This may cause it to drop or fall over,
w
There are high voltage
parts inside the cabinet A@
and this may cause an Electric shock Prohibition
electric shock. Ask your ‘=ard of
disassembly
dealer to check inside and adjust and
repair the unit.
Do not use this in abathroom, etc.
Do not use this unit in abathroom,
etc. This may cause afire, electric @
shock, etc. Do not use
near water
❑Do not look directly at the lens when
the lamp is lit.
Do not look directly at the lens when
the lamp is lit. Since astrong light Q
is used, it could damage you vision, etc.
Especially pay attention if children are present.
HDo not insert any foreign object.
●Do not insert ametal or flammable
object inside through the ventilation
holes, etc. This may cause afire, Q
electric shock, etc.
●If foreign matter enters inside, turn
the power switch off and disconnect e
the power plug from the power Pull out the
outlet and contact your dealer. If power plug
from the
you use as it is, it may cause afire, power
outlet.
electric shock, etc. Be careful
especially if children could touch the unit.
Do not apply any shock.
e
If you drop this unit or if the cabinet :
is broken, turn off the power switch,
disconnect the power plug and Pull out the
power plug
contact your dealer. If you use it as from the
it is, it may cause a&e, electric power
outlet.
shock, etc.
Do not remodel this unit.
Do not remodel this unit. It may @
cause afire, electric shock, etc. Prohibition
of
disassembly
Do not put acontainer, etc. with
liquid on this unit.
Do not put avase, flowerpot,
.s
cosmetic container, medicine or
water and small metal objects on this unit. If
liquid spills and enter inside the unit, it may
cause afire, electric shock, etc.
Do not use power supplies other
than that specified.
Do not use this unit with apower Q
voltage other than speciiled power
supply voltage. It may cause afire, electric
shock, etc.

WARNING:This equipment has been tested and found to comply with the limits for aClass Adigital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in acommercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications,
Operation of this equipment in aresidential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Instructions to Users:
This equipment complies with the requirements of FCC (Federal Communication Commission)
Class Aequipments provided that following conditions are met.
(1)
(2)
(3)
Video signal cables:
Double shielded coaxial cables (so called FCC shield cable) must be used and the outer shield must be
connected to the ground. Or, if normal coaxial cables are used, the cables must be enclosed in metal
pipes or similar way to reduce the interference noise radiation.
Power cord:
Shielded power cord must be used. The outer shield must be connected to the ground.
Video inputs:
The input signal amplitude must no exceed the specified level.
Before use
Before Use)
[illustrated marks Various illustrated marks are used in this product and instruction manual so
the product is used correctly and safely, and also to protect you and others from
danger and your property from being damaged.
~Warning This shows that aperson could be killed or injured if the
wrong operation is done by ignoring this indication.
~Caution This shows that aperson could be injured or material may be
damaged if the wrong operation is done by ignoring this
indication.
;xamples of
A
The Amark informs you that there is awarning (including caution).
llustrated marks The concrete details of the warning (the left diagram shows the
caution for an electric shock hazard) is shown in the diagram.
@
The @mark informs you of aprohibited action. The concrete
prohibited action (the left diagram shows the prohibition of
disassembly) is drawn in the diagram or near it.
G
The ●mark informs you of actions you must do. The concrete
instruction details (the left diagram shows “Disconnect the power
plug from the power outlet”) is drawn in the diagram.
3

■High temperatures are generated
when the lamp is lit, so do not place
objects in front of the lens. Q
EBe careful in handling the power cord.
●Do not scratch, damage or process the power .If the cord is damaged (core wire is
cord. Do not bend it forcibly. Also do not put aexposed, disconnected, etc.), ask
heavy object on it, do not heat it and do not pull your dealer to replace it. It may A1
●
it. If you do, the power cord maybe damaged and cause afire, electric shock, etc.
it may cause afire, electric shock, etc. ●Check that no dirt adheres to the
-Do not pull the cord.
.Do not put aheavy object on it. power plug and fully insert without any play. If
dirt adheres or the connection is incomplete, it
.Do not damage the cord. mmay cause afire, electric shock, etc.
.Do not put it near aheating .The outer shield of Dower cord must be
device. .
connected to ground.
.Be careful that this unit is not placed If you do not, it may cause a
on the power cord. The power cord maybe
damaged and it may cause afire, electric shock, electric shock.
etc. If the cord is covered with acarpet, etc. a
heavy object may be put on it without your
realizing it.
■Do not stare directly into the laser aperture.
●The laser pointer on the remote control unit radiates the laser beam from the laser
aperture.
●Do not stare ink the laser aperture or radiate the laser beam to other persons as the
laser emitted is aclass 2lasef and it could damage you vision ,etc.
Especially pay attention if children are present.
.The three labels below are caution labels for the laser beam.
\
~
DO NOT STARE INTO BEAM
CLASS 2LASER PRODUCT
WAVE LENGTH :67onm
MAX. OUTPUT: lmW
IEC60S2E-1 :19S3 +Al 1997 LASER APERTURE
E
---
5

EDo not step on this unit or do not put a
heavy object on it.
●Do not step on this unit. Especially @
pay attention if children are
present. If you do, the unit may fall over or
may be broken causing an injury.
.Do not put aheavy object on this unit. If you
do, the unit may fall due to its imbalance or it
may drop, causing an injury.
Do not block the ventilation holes.
Do not block the ventilation holes. If
the ventilation holes are blocked, the
heat inside may build up and it may Q
cause afire. Do not use this unit in
the following ways: On its side. In apoorly
ventilated, narrow place. On acarpet or
bedspread. Covered with atablecloth. Place this
unit so that the ventilation holes are kept 30cm
or more away from the wall.
Cleaning 4?!?
Be sure to pull out the power plug w
from the power outlet for safety Pull out the power
plug from the
when cleaning. power outlet.
❑Set the caster stoppers.
When this unit is installed on the
table with casters, set the caster AI
●
stoppers. If the table moves, it may
fall over, causing an injury.
HDonotplacethisunitinamoistor dustyplace.
●Do not place this unit in amoist or dusty place.
It may cause afu-e, electric shock, etc.
.Do not place this unit where it would
be exposed to soot or steam, near a@
cooking stove or humidifier, etc. It
may cause afire, electric shock, etc.
9Handle the power cord carefully.
●Do not bring the power cord near aheating
device. The shield of the cord may
melt and it may cause afire, electric
shock, etc.
.Do not insert /disconnect the power Q
plug with wet hands. It may
cause an electric shock.
.When the power plug is to be +!!!!!$
■
discomected, do not pull the
power cord. The power cord may be damaged and
it may cause a&-e, electric shock, etc. Be sure to
hold the power plug.
Caution when carrying it.
When this unit is to be moved, apply aa
cover to the lens and be sure to
discomect the power plug from the
power outlet and check that all
external connection cords are removed e
before moving it. If not, the cord Pull out the
power plug
may be damaged and it may cause from the power
afire, electric shock, etc. outlet.

■Use of batteries.
●Do not use batteries not specified
for this unit. Do not use new
batteries mixed together with old
ones. This may cause afie, injury @
due to burst of battery, liquid
leakage.
●When inserting batteries in this unit, pay
■
■
attention to th~ direction of the @- -
and @polarity indications and
insert the batteries correctly. If the At
●
polarities are confused, it may cause
injury or damage near the unit due
to burst batteries, liquid leakage, etc.
When you are not going to use
for along time.
e
When you are not going use this unit :
for along time because you are going
on atrip, etc., be sure to pull out the Pull out the
power plug
power plug from the power outlet for ~romthe
safety. And also apply cover to the power
lens so that the lens is not damaged. outlet.
Clean inside the unit at least once two vears.
Ask your dealer to clean inside the unit a;least
once two years. If the unit is left
with too much dust inside as it is for
along this without cleaning, it may AI
●
cause afire. Especially it is effective
to clean before the rainy season
starts. Consult your dealer for the cost of the
cleaning the inside the unit.
[General cautions]
9Caution when replacing the lamp. E
●When replacing the lamp, turn off the power of
the projector and disconnect the power plug ffom
the power outlet. Then wait for 45 —
minutes to allow the lamp cool: Failure
to do so could result in aburn.
●For disposal of used lamp, treat ~g
according to the instruction of Pull out the
community authorities. power plug
●Since the lamp is made of glass, do from the
not apply shock to it and do not power
scratch it. outlet.
.Also, do not use old lamp. This could also cause
explosion of the lamp.
●If it is probable that the lamp has exploded
(explosive sound is heard), disconnect the power
plug from the power outlet and ask your dealer
to replace lamp.
.In rare cases, the reflector and the inside of the
projector may be damaged by scattered broken
pieces of glass, and broken pieces could cause
injury when being handled.
●When the lamp has been replaced, reset the
accumulated operation time of the lamp.
Do not reset if the lamp has not been replaced.
Reflector glass
9Do not place this unit where it gets hot.
Be careful since if you place the unit
outdoors, in aplace exposed to direct
sunlight or near aheating device, @
the cabinet and parts could be
affected.
■Volume.
Use at the proper volume level so that it does
not bother persons in the neighborhood.
Especially, since the sound is likely to carry
well at the night even at alow volume, consider
the neighborhood to agood living environment.
■Cleaning the lens.
To clean the lens, use agenerally-
available lens cleaning tissue (used
for cleaning lens of camera, glasses, Q
etc.). Be careful not to scratch the
lens with ahard object.
■Cleaning the cabinet.
●Since many plastic materials are used on the
surface of the cabinet, if the surface is cleaned
using benzene, thinner, etc., it may change in
quality or the coating maybe peeled off. Avoid
using chemicals.
●When achemically-tested cloth is used, follow
the cautions that come with the cloth.
●Do not spray avolatile agent such as
insecticide on the unit. Do not leave arubber
or vinyl object touching the cabinet for along
time. It may cause the cabinet to change in
quality or the coating to peel off.
.Clean the dirt fi-om the cabinet and operation
panel by dusting lightly with asoft cloth. If
the dirt is conspicuous, wipe off with acloth
moistened with detergent diluted with water,
then wipe off with adry soft cloth.
■Rest your eyes occasionally when
viewing for along time. 7

Contents of shipping box
Check that the carton contains the following items.
Liquid Crystal Projector Remote Control Remote Control
Transmitter Batteries
Power Cord 3-Conductor RGB Cable
Ilov-us Mec adapter
Video/Audio Cable (15-15 pin M/M) with dip switch
220- UK, Europe
❑
☎☎☎
.xMwiErnB
----
—-
=--
—~. .
—.-w
—— i
--------
.—” —
~“
-.—
—
Operating Guide
Mouse cable X3
Names and functions of each part
ON indicator
This blinks in the standby mode and lights
in the operation mode.(See page 32)
INPUT button
To select the input source.
Each time this button is pressed, the input
source is changed in sequence as shown
below.(See page 13)
RGB1 —RGB2 —VIDEO
MENU button
Picture adjustments.
Refer to page 16-19 for details.
LAMP indicator ~~ IAMP
❑. . .. .. ,
This lights or blinks when the lamp does ~J TEMP indicator
not light. (See page 32)
\
This lights’ or blinks when temperature
inside the projector is too high or when fan
is abnormal.(See page 32)
ng
St)
e
fan
●Use the remote control transmitted within the range FOCUS ring .
of about 16 feet from the remote control sensor and Adjusts focus. (See page 13)
within 30° to both the left and right.
8

Names and functions of each part (continued)
Remote control sensor
a
MAIN POWER
Main power ON/OF
0: OFF
[:ON l!!v/
switch
‘F switch.
4
RGB input terminal WWZWWM
:
D-sub 15pin shrink terminal (1/2)
AC IN socket
Connect the provided power cord.
AUI
VIDEO input terminal
(on video-equipped models only)
S-VIDEO input terminal
Mini DIN 4pin connector
VIDEO input terminal
RCA Jack
AUDIO IJR input terminal
RCA Jack
1CON;ROL terminal
D-sub 15pin shrink terminal
I
10 output terminal 8
I/
I@ fi
(RGB/VIDEO)
Stereo mini jack I
Iinput terminal RGB output terminal
AUU
Stereo mini jack (1/2) D-sub 15pin shrink terminal
RGB output can be displayed
even in the standby mode.
9

Names and functions of each part (continued)
Remote control transmitter
STANDBY /ON button ==
Power ON/OFF button. ~%
OFF sets the unit in standby mode.
(See page 13, 14)
FREEZE Button ““~..%
Pressing this button displays astill picture
(by freezing). (See page 15)
MAGNIFY button ~
Pressing this button partially magnifies a
displayed picture. (See page 15)
POSITION button
Moves the picture by DISK PAD after
pressed the POSITION ON button.
(Only RGB signal input)
While the back light on, you can operate
POSITION. *1
DISK PAD /
@Whenthe back light of MENU ON button
on, selects or adjusts the menu item.
(See page 16)
@When removes the on-screen menus,
butiononmovespidd
works as mouse.
@When the back light of the POSITION ON
MENU ON button
J
Displays the on-screen menus.
And back light on. (See page 16- 19)
While the back light on, you can operate
MENU.
BLANK ON button
@The blank screen which is displayed by
pressing BLANK.
@And the blank screen will be revealed
down by pressing BLANK again.
(See page 19)
,L
L
INPUT SELECT button —
Selects the input source. (See page 13)
MUTE button
Silences the sound. (Cancels the mute when
the unit is set in mute mode.)
VOLUME button
Adjusts volume.The sound is loud or low
while pressing the “+”or “-”button.
LASER button
Laser pointer ON button. Use as a stick (for
indication). (See page 11)
MOUSE LEFT button
Mouse left button is the left click of the
mouse. (bottom button) (See page 23)
[gall PI
RESET /RIGHT button
When displays the on-screen menus, resets
the menu item to factory settings.
When operates the mouse emulation, works
as right click of mouse in computer mode.
(See page 23)
After moving the picture (POSITION ON),
resets the position to factory settings.
MOUSE ON button
Mouse emulation mode starts.
(See page 23)
When menu are open or blank screen is
displayed or icon of position is displayed,
there are stopped and back light off.
TIMER ON /OFF button
Displays the setting time by count down.
See page 19 “TIMER” of menu when you set
the minutes of timer.
*1 POSITION ON icon *2
When presses POSITION ON button, back light on and icon is When the back light of MENU ON or POSITION ON button on
displayed. without displaying the icon of POSITION ON or MENU, can
While displaying the icon, you can operate POSITION. operate DISK PAD too.
Icon is displaying in video mode, but can not operate POSITION. Displays the icon or MENU at the same time as starting the
operation.
When presses the MOUSE ON button, MENU mode or
r
POSITION ON mode is stopped.
PI
10

Names and functions of each part (continued)
●T
How to insert batteries
Insert the provided batteries LR6 (alkali) into the remote control transmitter.
❑Remove the battery ❑Insert the batteries
compartment cover. as illustrated inside
the battery compartment.
%
@
@o
—
Slide the battery compartment cover ❑Replace the cover.
in the direction of the arrow while
pressing slightly down on it.
●4
mcautions ‘n ‘se of batteries Cautions on use
●Do not use batteries not specfled for this unit. ●Do not drop the remote control transmitter or
Also do not use old and new batteries together. apply any shock to it.
It may cause afire, injury due to burst of .Do not let the remote control transmitter get
battery or liquid leakage. wet and do not put it on awet object. It may
.When inserting batteries, pay attention to the cause amalfimction.
direction of the @and @polarity indications .If you are not going to use it for along time,
and insert the batteries correctly. If the remove the batteries from the remote control
polarities are confused, it may cause injury or transmitter.
damage near the unit due to aburst of battery .If operation of the remote control becomes
or liquid leakage. diflicult, replace the batteries.
~(cm) Cautions on use of the laser pointer.
IThe laser pointer on the remote control unit radiates the laser beam fi-om the laser aperture.
1This laser pointer used as astick (for indication).
Do not stare directly into the laser aperture or radiate the laser beam to other persons as the laser
emitted is aclass 11laser and it could damage you vision ,etc.
Especially pay attention if children are present.
~The three labels below are caution labels for the laser beam.
‘~ F.%EkR%M”zcE
\
IASER RADIATION. RwNNEMEN7LASER MMwlwn
DO NOT STARE INTO B&4h4 NEFM REGMwERLMNS
LEFANEAUAPFh%lL JJKr3
WAVELEGM: 670nm ALASER
DECIASSE2
M4xoNTPlJT:lmw ~~F
CLASS 2LASER PRODUCT NICHTINDENSIRAliL iwwxlww
WXENIASAERS3A5SE2
\J
m
mLASER APERTURE

Installation
IExample of the projector and screen installation I
JI
Determine picture size and projection distance as illustrated below.
View from the top
Screen
View from the side
b
Lens center
a
IScreen (inch) k%k
I1
t40 64 I84
60 97 127
80 130 169
100 163 213
120 196 256
150 244 319
200 326 —
a:Distance from the projector to the screen.
(tolerance :*1 O%)
This screen size is full-screen size.(1024 dots X768 dots)
Installation of liquid crystal projector d
Please basically use liquid crystal projector at the horizontal
position.
If you use liquid crystal projector by the lens up position, the lens
down position and the side up position, this may cause the heat
inside to build up and become the cause of damage.
Be especially careful not to install it with ventilation holes blocked.
IHow to use foot adjusters I
7I
idjust the projection position using the foot adjusters at the bottom of the projector.
(View from the front )
Foot
Vertical adjustments
can be made in the
range of Oto90.
cView from the side )
u
a’ Horizontal inclination
2may be adjusted using the adjuster at the rear.
1. Lift up the projector and press the button of the adjuster to release the lock.
2. Adjust the projection angle, release the button of the adjuster and securely lock it.
3. To adjust the angle slightly, revolve the foot adjusters.
E@il ●Do not unlock the foot adjusters while you do not support the projector, to avoid falling of
the projector and causing an injury.
.Do not revolve the foot adjusters by force, the foot adjusters is damaged.
.Securely lock the adjuster.
.Do not apply unnecessary force from the upper side when lifting the projector. Otherwise,
projector may be damaged or afinger could be caught and cause injury.
,
12

Basic operations
To project the picture 2
?3
74$
@&b@
rSTANDBY/ON MUTE
$(xl
FREEZE
A
cmma MAGNIWVOLUME
mmB
POSITION ON IASEI
37
c)
>9 RIGHT
1Turn the MAIN POWER switch of the projector on.[ I:ON]
.The ON indicator will light up orange.
~Press the STANDBY/ON button.
6.The ON indicator blinks (green) during warm-up and then lights (green).
.Power cannot be turned on even if the STANDBY/ON button is pressed within 60 seconds after
power is turned off, since the lamp has cooled preparing for next lighting.
9Remove the lens carx
m
4Adjust picture size using the projection lens ZOOM knob.
>5Adjust focus using the projection lens FOCUS ring.
6Power on all connected equipment.
The method of connecting various equipment, see on the page 20-28.
7P ress the INPUT button or the INPUT SELECT
RGB) button to select the source of the signal
on the screen.
●The selected signal input is displayed at the bottom right of the screen
for 3seconds.
(VIDEO or
to be projected
Example on-screen display
u
13

Basic operations (continued)
To turn off the power 11
[w@4i2h@
STANDBY/ON MUTE
FREEZE
)SITION ON LASE
7r
[MENU oNj MOUSE ON’
o
u
BIANK TIMER
QJo VIDEO
~hWUT~
+Press the STANDBY/Ohl button, for 1second.
m●The ON indicator blinks orange and the lamp turns off. (About 1minute later), the fan stops and
the indicator lights up orange.
.Press the STANDBY/ON button for short time (less than 1second), the projector do not set in
standby mode.
2Turn the MAIN POWER switch of the projector off.[o: OFF]
3Install the lens cap.
@a oTo reduce temperature inside the projector, fan will rotate for about 1minute after the lamp
is turned off.
●Do not turn off the MAIN POWER switch during the lamp on because the lamp is damaged.
IEEEEEl
This projector complies with VESA DDC1/2B specifications. PLUG&PLAY is asystem with computer,
peripherals (including projectors), and operating system.
It works when the projector is connected to DDC (Display Data Channel) ready computer that is running
an operating system software that incorporates plug &play functionality.
(Only RGB 1)
14

Basic operations (continued)
FREEZE FUNCTION C9A@Y
This function can display astill picture (by freezing). This function can fSTANDBYION MUTE
be used in combination with aMAGNIN function. Em
1P 1,2 -“I!zl,
EElvg,
ress the FREEZE button.
The display image stops. AIi mark appears at the lower right of mmB
POSITION ON USER
the screen for about 3seconds during the FREEZE function. 00
[TO RELEASE FREEZE] n
2Press the FREEZE button.
The freeze function is cancelled. Furthermore, a}mark appears at the bottom of the screen for 3
seconds or so when FREEZE is released.
@@ .Note: When the FREEZE Button is pressed, FREEZE and RELEASE can function alternately.
QWhat is more, FREEZE is released when an input selector button is pressed or when the
display mode of apersonal computer is switched over during display.
.The POSITION ON icon is not displayed during freeze. Also, scrolling using DISK PAD
operation is not possible.
.When astill picture signal is given as input and the freeze function is ON, do not forget to
cancel the freeze fimction.
MAGNIFYING FUNCTION
It is possible to display apartialIy magn~led picture. This function can be used in combination with a
FREEZE function.
1P ress the MAGNIFY +button.
●By doing so, the center of the picture can be magnified as one
part, becoming double in size.
[TO CHANGE MAGNIFICATION] 1,2
2P ress the MAGNIFY +button. 6
●When the button is pressed, more magnification of display
takes place. (Maximum about 4times)
34
Press the MAGNIFY -button.
.When the button is pressed, the magnified display reduces its 5
size. (Minimum about 1.1 times)
[TO SHIFT DISPLAY AREA]
4Press the POSITION ON button.
5Press the DISK PAD button up and down and left and right.
.The magnified display area shifts in the direction the button is pressed.
[TO RETURN TO NORMAL DISPLAY]
6Press MAGNIFY OFF button.
G@Note: The MAGNIFY function is released when an input selector button is pressed or when the
display mode of apersonal computer is switched over during display. 15

Adjustments and functions m
@
,(4I
@lPKl
FREEZE
Slmciwm
o
00! O@Elm
INPUT MAGNIFY VOLUME
~o m3El
POSITION ON USER
Q
MENU
A
<b 00
RfSET
o
e
2,3A- ~h
I
1,2,3 -F7
RESET R1’dHT
1
MENU ON MOUSE ON
‘.X%23’ o
BLANK TIMER
Qo VIOEO
~INPUT~
1Press the MENU (@ @ @o) buttons or the MENU ON /
OFF button.
.On-screen menus are displayed on the screen.
4
2Select the menu to be adjusted using the MENU (@ @ )
buttons or DISK PAD.
●Menu displayed in green is selected.
3Select the item to be ad]usted using the MENU (@ @ @ @)
buttons or DISK PAD.
●Item displayed in green can be adjusted.
When no operation is done for about 5- 10 seconds, menu screen will go off.
*
Memory function
Individual memory functions are provided for the VIDEO, RGB1 and RGB2 input terminals. Adjustments .
are saved after power off.
To return to the initial setting
●Resetting menu items (SETUP, INPUT, IMAGE, OPT. )
(1)Select the menu item to return to the initial setting.
(2)Press the RESET button.
(NSelect the DEFAULT (To select the CANCEL is not changed).
(Display shown on the right will appear.)
.Resetting adjustment items (VOLUME, BRIGHT etc.)
o) Select the adjustment item to return to the initial setting.
@)Press the RESET button.
16
-lNf’uT IMAGE OPT
al
VOL
BRI RESET ‘SETUP’ o
co ■DEFAULT @
SHA
COL El CANCEL
TIN
COLOR BAL R~ B

-.
b
Adjustments and functions (continued)
EmEl The menu SET UP serves for the change of parameters influencing the picture and for
the move picture position.
RGB signal input VIDEO signal input
Magnify ~g;:$
Adjustment Item Details of adjustment Freeze
VOLUME Decrease ~Increase o0 0
BRIGHT
(BRIGHTNESS) Dark ~Bright o0 0
CONTRAST Lower ~Higher o0 0
SHARPNESS soft ~Sharp xox
COLOR Less ~More xox
TINT Red ~Green xox
V.POSIT
(V. POSITION) Moves the picture up or down. Or automatic control. xx x
H.POSIT
(H.POSITION) Moves the picture left or right. Or automatic control. xxx
H.PHASE Decreases the picture flicker. Or automatic control. xox
H.SIZE WidensofNarrowthehorizontalsizeofthepicture.Orautomaticrxmfrol. xx x
COLOR BAL
(COLOR BALANCE) for Red ~for Blue o0 0
0: operation is possible. x: operation is not possible.
How to use the SETUP menu
1.Bar display items (VOLUME, BRIGHT etc.)
Move the green cursor to the item you wish to adjust, then move the MENU buttons on the unit, or the
DISK PAD, to left and right to adjust the length of the bar display. Some items can not be adjusted
during ffeeze or during magnify. (Please refer to the above table.)
2. Numerical display items (V POSIT, HPOSIT etc.)
Use either manual operation or auto-adjustment. Some items can not be adjusted during freeze or
during magni@. (Please refer to the above table.)
<Manual Operation >
Adjust optional items manually. mINPUTIMAGEoPT.
(1) Use the MENU buttons on the ‘unit or the DISK PAD on the remote VOLUME
BRIGHT ❑
~H
control to move the green cursor to the number of the item you wish to CONTRAST ~o
VPOSIT ~: AUTO @
adjust. HPOSIT
J
m
HPHASE 31
(2) With the green cursor on the number, use the MENU buttons on the HSIZE 1024 9
COLORBAL R~ B
unit or the DISK PAD on the remote control to raise or lower the
value.
m-
17

Adjustments and functions (continued)
<AUTO-adjustment >
The projector will automatically adjust four items (V POSIT, HPOSIT, HPHASE, HSIZE, White level).
When AUTO is selected (the cursor is moved from Manual Operation towards the right) the AUTO Confirm
screen shown below will be displayed.
<AUTO-adjustment Confirm Screen >kE@ INPUTIMAGEOPT
While the AUTO confirmation screen is displayed as illustrated on the
d
VOLUME
upper right, if you shift the cursor upward and select AUTO, the projector BRIGHT
CONTRAST
will perform auto-adjustment.
It will become as illustrated on the lower right. ~;, m=!
If CANCEL is selected for three seconds, or if the RESET button on either COLORBAL R~ B
the unit or the remote control is pressed, the green cursor will return to
the value for the selected item (Manual Operation)
<During AUTO-adjustment >a
At the lower right of the screen the word .AUTO> will flash in green
letters.
When the auto-adjustment is completed the word AUTO> will disappear.
The auto-adjustment of the white level is cancelled by input switching and AUTO
signal mode change. I1
@@ *When start up screen is displayed (“NO INPUT IS DETECTED” or “SYNC IS OUT OF RANGE” is displayed), SETUP menu items other than VOLUME cannot be set.
.TINT cannot be adjusted with PAL/SECAM video signal input.
●TINT, COLOR and SHARPNESS cannot be adjusted with an RGB signal input.
.V.POSIT, H. POSIT, H.PHASE and H.SIZE cannot be adjusted with aVIDEO signal input.
.Auto-adjustment will take about 10 to 15 seconds to complete.
.In some cases auto-adjustment may not function normally, depending on the type of
computer to which the unit is connected, and the signal sent.
.Auto-adjustment may not perform normally with some images. Do not use with animated
or dark images.
●Carry out the auto-adjustment when the application, which is activated on the computer, is
set to the maximum display.
.After auto-adjustment the screen may become slightly dark due to the auto-adjustment of
the signal level.
●Auto-adjust can not be performed during freeze, during magnify, or during the initial
screen display (“NO INPUT IS DETECTED” or “S~C IS OUT OF RANGE”).
INPUT The menu INPUT serves for the selection of input source.
n~1 ml
Adjustment Item Details of adjustment
RGB 1Selects the RGB 1terminal.
RGB 2Selects the RGB 2terminal.
VIDEO Selects the VIDEO terminal.
Selects the video signal systems. In normal circumstances, select AUTO. AUTO does not
SYSTEM support N-PAL.
When the picture (Video) is abnormal (no color), selects the input signal mode (NTSC,
IIPAL, SECAM, NTSC4.43 M-PAL and N-PAL). To input N-PAL signals, select N-PAL,
18

Adjustments and functions (continued)
L!!!EEl
The menu IMAGE serves of the picture inversion.
mBE
SETUP INPUT wOPT. SETUP INPUT =OPT.
❑
REVEAL ■FAST
m
MESSAGE ■TURN ON
❑-r
II MEOIUM
❑+
II SLOW
I I I 1
Adjustment [tern
MIRROR
BLANK
Details of adjustment
Inverts the picture horizontally or vertically.
NORMAL Not invert.
H: INVERT Inverts the picture horizontally.
H: INVERT inverts the picture vertically.
H&V:lNVERT Inverts the picture horizontally and vertically.
Selects’the blank color of signal. See page 10 “BLANK ON button.
When start up screen is displayed, screen will blank out 5minutes later.
IREVEAL ISelects the speed or revelation. See page 10 “BLANK ON button.
,MESSAGE Turn off the on-screen message. (VOLUME, Input selection display)
mThe menu OPT. allows you to control communication function etc.
SETUP INPUT IMAGE ~
Adjustment Item I
COM. SPEED
(COMMUNICATION SPEED) ‘
COM. BITS
(COMMUNICATION BITS)
TIMER
LANGUAGE
AUTO OFF
START UP
SETUP INPUT IMAGE ~SETUP INPUT IMAGE ~SETUP INPUT IMAGE ~
Details of adjustment I
Selects the data speed of transmission. (five kinds)
Selects the data format or transmission
7NI ...7 data bits, No parity, 1stop bit. ““l
8NI ...8 data bits, No parity, 1stop bit.
Sets the minutes of timer. (0-99)
Selects the language on-screen menu. I
(English, Fran~ais, Deutsch, Espahol, Italiano, Norsk, Nederlands) I
Sets time (minutes) from the start of displaying start up screen (No input is detected or
sync is out of range) to turning the power OFF. “O is stop and another”1 -99
Sets/releases start up screen displayed when power is turned on, or when no input is
detected or sync is out of range.
k
—
.
19

Connection to the video signal terminals
1. Input signal
S-VIDEO signal Luminance signal 1.OVp-p, 75Q termination
Chrominance signal 0.286VP-P (burst signal), 75!2 termination
VIDEO signal 1.OVp-p, 75S2termination
Input 200mVrms, 20kQ below (MAX 3.OVp-p)
AUDIO signal output O-200mVrms, 1Id2
2. Signal input terminal
Chrominance signal Luminance signal
Ground Ground
SVIDEO input (Mini DIN4 pin)
@iE)
Video input signal terminals have priority in the following order.
OS-VIDEO input terminal @RCA jack input terminal
Even when the video signal is displayed, only an audio signal is output to RGB audio output terminals.
Connection to the RGB signal terminal
“
1. Input/ output signal
Video signal IAnalog 0.7Vp-p 75Q termination (Positive polarity) I
IHorizontal sync signal ITTL level (Positive/negative polarity) I
Vertical sync signal TTL level (Positive/negative polarity)
IComposite sync signal ITTL level I
Input 200mVrms, 20kQ below (MAX 3.OVp-p)
Audio signal output O-200mVrms, 1I@
2. Signal input/ output terminal
1]Video signal (Red) I9]N.C I
2Video signal (Green) 10 Ground
3Video signal (Blue) 11 N.C
4IN.C I12 IDDC (Display Data channel) RGB1 only I
5IN.C I13 IHorizontal/Composite sync signal I
6IGround (for R) I14 IVertical sync signal I
#II
7IGround (for G) I15 IDDC (Display Data channel) RGB1 only
8IGround (for B)
1
,fmg
00000 6
00000
’15 11
D-sub 15pin shrink terminal
(Female)
@@ Do not use RGB cable other than that specified.
Some RGB cable may not operate DDC (Display Data Channel).
With other cables, pins @,@are sometimes not connected.
20