Holis JSE04-D10-OI01 User manual

Figure 3: Micro SD card slot and reset button (continued)
Note: Remove the four screws on the camera cover (1) (Figure 1) to
access the buttons. Securely attach the cover when finished.
Table 3: Micro SD card slot and reset button
Number
Camera button description
1
Micro SD card slot
2
Reset button (Hold for more than 3 seconds)
Quick reference
Default IP: 192.168.1.168 (DHCP enabled).
Default Username / Password: admin / admin
Power: 12VDC or PoE
Use Internet Explorer 11 web browser.
Mounting the camera to a wall or ceiling
Ensure that the wall or ceiling is strong enough to withstand three times
the weight of the camera.
1. Place the mounting template on the surface that you want to attach
the camera.
2. On the surface drill four Ø 4.6mm holes and cut out a cable hole as
per the markings identified on the mounting template.
3. Securely place the four screw anchors into the four holes.
4. Remove the four screws on the camera cover (2) (Figure 1) to
remove the cover from the camera base (1) (Figure 1).
5. Place the camera cable through the cable hole on the mounting
surface.
OR
Use the cable side entry hole slot on the camera base.
Security
Quick Start Guide
(8200-1994-05_C0)
Tyco Holis JSE Economical 4MP Mini Dome Cameras
(Product Code: JSE04-D10-OI01 and JSE04-D30-OI03)
In the box
1 x Camera
1 x Quick Start Guide
4 x 4x25mm tapping screws
1 x Mounting template
4 x 6x25mm Plastic screw anchors
1 x Silicone plug
1 x L-Key Hexagonal wrench
1 x Regulatory Document
Installation tools
Screwdriver
Drill
L-Key Hexagonal wrench
Figure 1: Camera parts
Figure 1
Table 1: Camera part descriptions
Number
Camera part description
1
Camera base
2
Camera cover
3
Camera dome
Figure 2: Cable connections
Figure 2
Table 2: Cable connection descriptions
Number
Cable connection description
1
Ethernet Connector and also supports PoE
2
Power Connector (12V DC @ 1A)
Figure 3: Micro SD card slot and reset button
Figure 3
Mounting the camera to a wall or ceiling (continued)
Note: If you are not using the cable side entry slot then ensure that
the cable side entry plug is inserted into the slot on the camera
base.
6. Hold the camera base (1) (Figure 1) up to the mounting template
and align the four holes on the camera base with the four holes on
the mounting surface.
7. Insert the four screws into the four holes on the camera base and
securely attach the camera to the mounting surface.
8. Hold the camera base cover up to the camera base and align the
four holes on the camera cover with the four holes on the camera
base.
9. Insert the screws into the four holes and securely attached the
camera cover to the camera base.
10. To power up the camera:
Connect a 12V DC power supply to the power connector on
the camera cable.
OR
Connect a shielded PoE cable to the ethernet / PoE slot on
the camera cable.

Security
Figure 5: Camera pan, tilt and rotate
Figure 4
Warnings
If the product does not work properly, please contact your dealer
or the nearest service centre. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance).
In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the
product is mounted on wall or ceiling, the device shall be firmly
fixed.
Do not allow water or liquid intrusion into the camera.
Do not use camera beyond specified voltage range.
Do not drop the camera or subject it to physical shock.
Avoid touching the camera lens.
If cleaning is necessary, please use clean cloth to wipe it gently.
Do not aim the camera at the sun or extra bright place.
Do not place the camera in extremely hot, cold (the operating
temperature shall be -30˚C~60˚C), dusty or damp locations, and
do not expose it to high electromagnetic radiation.
To avoid heat accumulation, good ventilation is required for
operating environment.
© 2021 Johnson Controls. All rights reserved.
JOHNSON CONTROLS, TYCO, and HOLIS are trademarks and/or
registered trademarks. Unauthorized use is strictly prohibited.