Home Sentinel CA1022 User manual
B/W PAN/TILT
FIXED DOME
CAMERA
OWNER’S
MANUAL
INSTALLATION AND OPERATION
BEFORE INSTALLING OR
OPERATING THE SYSTEM,
PLEASE READ THIS MANUAL.
MODEL: CA1022CA1022
Remove all packaging and clear it away before plugging in the CA
1022 Dome Camera
Read the installation instructions carefully before proceeding
Do not attempt to repair any part of the system by opening the
casing. If the camera requires repair, phone 1-800-268-9852
If storing the system, choose a cool, dry location. Protect the camera
from dust and do not store any heavy objects on top of the unit.
Do not install the camera near water, oil, or heat source areas such
as a stove.
Use of unauthorized cables and accessories are not recommended.
Attaching incompatible parts may damage the system.
Important Safety Instructions
1
Table of Contents
2
Section Page
Important Safety Installations ................................1
Table of Contents ..............................................2
Introduction ....................................................3
Packing List ....................................................3
Features .........................................................4
Key Components ..............................................4
Installation procedure .........................................5
Installing the Dome Camera with a Control unit and
Surveillance Monitor ...........................................6
Installing the Dome Camera with a Control unit,
Surveillance monitor and 2 or 4 cameras .......................6
Trouble Shooting Guide .......................................7
Specifications ..................................................7
Warranty .........................................................8
3
Congratulations on choosing the Home Sentinel CA 1022 B/W Pan/Tilt
Fixed Dome Camera. The CA 1022 system is reliable, versatile, and is
produced with high quality standards.
This versatile dome camera must be used with the PT 400 Pan/Tilt
control unit for the motorized mechanism to pan and tilt. This dome
camera and controller can be integrated with your existing Home
Sentinel video surveillance system.
This compact smoked acrylic dome blends with any décor and provides
discrete video surveillance. The built-in microphone provides audio
monitoring as well. The motorized controls has the ability to give you a
viewing angle of 355 horizontal and 85 vertical.
Introduction
Packing List
1. B/W Pan/Tilt Dome Camera
2. 65 ft Din Cable (6 pin)
3. 6 ft Din Cable
4. Mounting hardware
4
Key Component
•A reliable, high quality 1/3” CCD Camera providing optimum image
clarity
•Electronic IRIS for use in applications with a wide angle spectrum of
lighting
•Pan/Tilt controls (with a PT 400 Pan/Tilt Control unit)
•3.6mm lens, 1 lux (f2.0)
•Operating Temperature : -10 C ~ +50 C
Features
Adaptor plate
Ø3 x 20 screw
Hook
Base (hold base when you
twist to attach the
dome to adaptor plate)
Swivel
Bubble
5
Installation Procedure
A
105
105
107
FRONT VIEW TOP VIEW
WHITE (VIDEO OUT)
RED (+12V)
Before installation, make sure:
(A) Proper lift equipment or ladder to reach the installation
(B) Electrical power is not connected to the dome and surveillance
monitor during installation
To install the dome camera on a ceiling or wall follow these procedures:
1. Twist open the clear dome cover in a counter-clockwise direction to
reach inside the dome camera. (turn at the swivel section of the
camera)
2. Place the PT400 Control unit on a flat surface
3. Connect the 6 ft Din cable from the controller, marked “To Monitor”
from one of the channel outputs CH 1,2,3 or 4 to the corresponding
camera input CA 1,2,3 or 4 on the back of the monitor.
4. Run the 65 ft Din cable (included with the dome camera) from the
wired lead of the dome camera to the control unit, marked “To
camera” CH 1,2,3 or 4.
5. Please note : If the camera input on the controller is on CH 1 then the
monitor output on the controller must also be a corresponding CH 1
6. Attach the adapter plate on the ceiling or wall, using the 3 screws
provided (M3 X 20 screw).
7. Twist the base of the dome camera onto the adapter plate already on
the ceiling/wall. Note : Do not hold the clear bubble or swivel when
you attach the dome to the adapter
8. Repeat steps 1 to 6 to install other dome cameras.
6
Installation Procedure
• Installing the Dome Camera(s) with a Control unit and
Surveillance Monitor
CAMERA 4
PAN/TILT DOME CAMERA
CA 1022
CAMERA 3
CAMERA 2
CAMERA 1
PAN/TILT DOME CONTROLLER
PT 400
MONITOR
6 Pin DIN cable
6 Pin DIN cable
6 Pin DIN cable
6 Pin DIN cable
POWER
AC IN PUT
ALARM OUT
COM
NC N.O CAMERA IN PUT
V C R
IN OUT OUT
AUDIO
VIDEO
SLAVE
1 2 3 4
VIDEO IN
1 2 3 4
AUDIO IN
CA1 CA2 CA3 CA4 REMOTE
CH1 CH2 CH3 CH4
TO MONITOR TO CAMERA
CH1 CH2 CH3 CH4
• Installing the Dome Camera(s), Control unit, surveillance
monitor and 2 or 3 cameras
PAN/TILT DOME CAMERA
CA 1022
CAMERA 2
CAMERA 1
PAN/TILT DOME CONTROLLER
PT 400
MONITOR
6 Pin DIN cable
6 Pin DIN cable
POWER
AC IN PUT
ALARM OUT
COM
NC N.O CAMERA IN PUT
V C R
IN OUT OUT
AUDIO
VIDEO
SLAVE
1 2 3 4
VIDEO IN
1 2 3 4
AUDIO IN
CA1 CA2 CA3 CA4 REMOTE
CH1 CH2 CH3 CH4
TO MONITOR TO CAMERA
CH1 CH2 CH3 CH4
CCDCAMERA
CAMERA 3
CAMERA 4
7
Troubleshooting Guide
Before calling for service, please use the following guide for possible
solutions Problem Solution
No picture Check that the camera is plugged in
Check that the cable connection at the
monitor is plugged in
Picture, but no sound Check the volume control on the
monitor.
Check that nothing is impeding the
microphone at the camera location
Pan or Tilt does not work Call for service
Specifications
Power Source 12V (from controller)
Image sensor 1/3” B/W CCD
Active pixels EIA : 512(H) X 492(V)
Image sensor area 4.8(H) X 3.7(V)mm
Signal to noise 46dB
Electronic IRIS 1/100,000 seconds
Synchronization Internal
Signal format EIA : 525 lines, 2:1 interlace
Video output 1.0V p-p (75 ohm)
Audio output 600 ohm line level
Ambient temperature -10 C ~ +50 C
Ambient humidity 0-96% Non-condensing
Resolution Greater than 380 TV lines
Minimum illumination 1 Lux
Lens 3.6mm
Power consumption Max. 2.4W
Warranty
Home Sentinel warrants this home security product (“The Product”) to be
free from defects in material and workmanship for a period of one year
from the date of purchase. This warranty does not cover any expenses
incurred in the removal and reinstallation of the product. This warranty is
offered to the original purchaser of the product only.
If the product should prove defective within the warranty period, return
the product postage prepaid to Home Sentinel, along with your dated
sales slip or other proof of purchase which will establish your eligibility
for the warranty. Home Sentinel will at its option, replace or repair the
product free of charge and return the product to you postage prepaid.
This warranty dose not apply to the product which has been damaged,
misused, altered or repaired by anyone other than a Home Sentinel
authorized service facility.
ANY IMPLIED WARRANTIES INCLUDING FITNESS FOR USE AND
MERCHANTABILITY ARE LIMITED IN DURATION TO THE PERIOD OF
THE EXPRESS WARRANTY SET FORTH ABOVE, AND NO PERSON
IS AUTHORIZED TO ASSUME FOR HOME SENTINEL ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE OF THE PRODUCT.
HOME SENTINEL EXPRESSLY DISCLAIMS LIABILITY IN
CONNECTION WITH THE SALE OF DAMAGES CAUSED BY THE
PRODUCT. THE REMEDIES PROVIDED UNDER THIS WARRANTY
ARE EXCLUSIVE AND IN LIEU OF ALL OTHERS.
This warranty gives you specific legal right, and you may also have other
rights which vary from state to state or province to province. Some
states/provinces do not allow limitation to how long warranty lasts, so the
above limitation may not apply to you. Additionally, some
states/provinces do not allow the exclusion of limitation of consequential
or incidental damages, so the above limitation or exclusion may not
apply to you.
8
DISTRIBUTED BY:
MANSOOR ELECTRONICS LTD.
310 ALDEN ROAD, MARKHAM,
ONTARIO, CANADA L3R 4C1
TEL: (905)475-8444 FAX: (905)475-3576
TOLL FREE: 1-800-268-9852
www.mansoorelectronics.com
Table of contents
