HomeAware HA360US Assembly instructions

INSTALLATION AND SET UP FOR HA360US – Universal Signaler
The HomeAware™ HA360US is designed to alert you
to many sounds. This signaler alerts you through the
HomeAware™ Main unit and remote receivers located
in other rooms.
Battery Backup Installation
Install a new 9 volt alkaline battery into the battery
compartment located on the back of the unit. See
diagram for battery door location. Battery backup will
provide power when a power outage has occurred.
Power will be provided for a continuous outage lasting
7 days, or for short outages up to two years.
Link Button Set Up
This procedure will link the HA360US – Universal
Signaler to your Main unit. The Main unit will also
provide an alert to all HomeAware™ remote receivers.
When using the Bridge unit HA360BU all original Sonic
Alert receivers (SA101, SA201, BL300, and SB1000)
will also alert you.
It is best to do the link procedure in the same room with
the HomeAware™ Main unit, make sure the unit is
plugged in.
To link the signaler to your HomeAware™ Main
unit:
1. Press set up button and the word LINK will be
shown on the display, press Enter. LINK will begin
blinking. (If LINK mode is entered by accident,
simply press the BACK button to exit and return to
the clock.)
2. Press and hold down the Link button on the back of
your transmitter for about 1 second. The red LED
on the signaler will light up. Release the button.
3. Pick Device will scroll across the display, hit the
TONE button to pick which device you want to be
alerted to (see list of devices below). Once you see
the device hit the ENTER button.
4. Upon successful connection, the red LED on the
transmitter will flash 2 times, then turn off. The
HomeAware™ main unit will briefly show DONE,
and return to the time display. Your signaler is now
connected and ready to test and use.
List of Devices in order:
INTCOM (INTERCOM), KITCH (KITCHEN), GARAG
(GARAGE), DRVWY (DRIVEWAY), MDALRT (MEDICAL
ALERT), OXYGEN, FLOOD, PET
Sensitivity Switch
You can adjust the sensitivity of the detector. There are
three levels to choose from: The HI setting is the most
sensitive setting and will alert you to more sounds.
Moving this switch to MED makes it less sensitive and
will alert you to less sound. The LO setting is the least
sensitive. If you are not picking up the sound you need
to be alerted to, simply move the sensitivity switch to a
higher setting. If you have set this setting to HI and you
are still not picking up the sound try moving the
transmitter closer to the sound.
When a sound is detected it will send a signal to the
HomeAware™ base unit and all HomeAware™ remote
receivers, also the red LED light will flash on the front
of the unit.
Low Voltage Input
HomeAware™ transmitters have a low 120 volt AC
power supply that powers the HA360ss. Simply plug
the unit into any 120 volt AC power outlet. Next plug
the other end into the Low Voltage Input located on the
side, see diagram.

INSTALLATION AND SET UP FOR HA360US – Universal Signaler
FCC Requirements
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions; (1) This
device might not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15
of the FCC rules. These limits are designed to provide
responsible protect against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions manual, may cause
harmful interference to radio communications. However, there
is no guarantee that interference will not interfere in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment on and off, the user is
encouraged to try to correct the interference by one or more
of the following measures:
i. Reorient or relocate the receiving antenna.
ii. Increase the separation between the equipment and
receiver.
iii. Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
iv. Consult the dealer or and experienced radio /TV
technician for help
Modification not expressly approved by the manufacturer
could void the user’s authority to operate the equipment
under FCC rules.
GENERAL DATA
UL listed Power Adaptor: AC100-240V~, 50/60Hz
Power Consumption: Adaptor Output: DC12V, 250mA
The Lightening
flash and
arrowhead within
the triangle is a
warning sign
alerting you of
dangerous voltage
inside the product.
CAUTION:
TO REDUCE
THE RISK
OF ELECTRICAL
SHOCK, DO
NOT
REMOVE THE
COVER
(OR BACK)
FROM THE
PRODUCT. NO
USER
SERVICEABLE
PARTS
INSIDE. REFER
SERVICING TO
YOUR SONIC
ALERT DEALER.
The exclamation
mark within the
triangle is a
warning sign
alerting you of
important
instructions
accompanying
the product.
WARNING: TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
The normal function of the product may be
disturbed by Strong Electro Magnetic Interference.
If so, simply reset the product to resume normal
operation by following the instruction manual. In
case the function could not resume, please use the
product in other location.
–Attention should be drawn to the environmental
aspects of battery disposal.
–TThis indicating separate collection for
electrical and electronic equipment.
SONIC ALERT’S 1 YEAR LIMITED WARRANTY
The HomeAware™ HA360US are warranted against
manufacturing defects in materials and workmanship
for one (1) year from the date of purchase. Within
this period Sonic Alert will repair or replace at our
option the HomeAware™ HA360US without charge
for parts and labor.
Simply contact our customer service
department for a RA (return authorization
number) and instructions on how to process
your product for return. Call 248-577-5400 or
e-mail to [e-mail].
You’ll need a copy of your receipt to process
the return authorization.
Sonic Alert
850 Stephenson Hwy., Suite 323, Troy MI, USA.
Made in China
Sonic Alert, Troy, MI 48083
www.SonicAlert.com