Homeguard HGWIP811 User manual

Quick Start Guide
HGWIP-811
TM
TM

Thank you for choosing HOMEGUARD.
Getting starting is easy.
Welcome
3
ELDERLY
Relatives
CHILDREN
Sleeping/playing
PETS
Monitoring
HOME
Surveillance
2
WHEREVER YOU ARE
GIVES
PEACE OF MIND

What’s included Part names & Functions
Camera Quick Start Guide
Warning Sticker
User Manual
Power Adapter Ethernet Cable
Antenna
Bracket
4 5
Full Colour HD Video
Camera captures high quality 1080P HD video
and includes infrared LEDs to give night vision
Pan & Tilt
Motorised lens can swing left & right, up &
down, remotely controlled from your
SmartPhone or other device
Save to SD Card
Camera can save footage and stills to a SD
card (up to 128GB capacity, not included )
Two-Way Talk
Camera includes a microphone and speaker so
you can listen and speak back to where the
camera is located
Wireless Transmission
The camera signal is transmitted wirelessly to
your internet router, then onto the internet to
share securely with your viewing device(s)

Get the App Network Connection
Step 1
For the best experience, download the Homeguardcare app for your smartphone by scanning the QR code below or searching for
“Homeguardcare” in the app store.
LED status
LED indicator shows operational status with colors.Refer to table below for detailed meaning of the LED indicator.
Connect the camera to your router
using an Ethernet cable.
Connect the AC adapter to
your camera and plug it in.
Make sure you are within range of the
same Wi-Fi network you'll use for your
camera.
6 7
LED Indicator
Blinking quickly
Blinking slowly
Keep blue (Network status)
Keep red (Working status)
The indicator is off 1. RJ45 Connection: wired connected
2. WiFi connection is failed The device is not launched
Network status indicator Blue color
WiFi configuration succeeded Begin to upgrading
Working status indicator Red color
Connecting to WiFi by One Key
Configuration on App
1. WPS configuration: to search available WPS AP
2. WiFi mode: to connect the available WiFi signal
The device works normally
but no Internet connection
Internet connected

Camera Settings
Step 2 Wireless Connection Step 3
HOMEGUARDIP Camera
PartNO.: XXXXXXXX
Username: admin
Password: 123456
DID: VIEW-000117-LZVZU
DDNS: 005mryg.nwsvr1.com
Enter the default
Password “123456”
3
Click “Scan QR Code”Click “add camera” Click the setting button Click “Advanced Settings” Click “WiFi Setting”
3Choose your home “Router”
and type in the “Password”
4
8 9

Before you begin your IP Camera Set up, please:
Have your IP Camera and power adapter ready.
Have your iOS / android device available to download the Homeguardcare app.
Make sure you are within range of the same Wi-Fi network you'll use for your camera.
Run the app and add camera by scan the QR code at the bottom of the camera; Then input the user name and password.
Click "More", select "Wi-Fi Config", fill in the Wi-Fi password and click "Configuration".
10 11
One Key WiFi Connection
OR YOU CAN CHOOSE
You’re Done!
Congratulations! Your HOMEGUARD Camera is set up and ready to go.
You can now safely disconnect your Ethernet cable.
You are now free to position your camera anywhere in your home where you get a WiFi signal and view it
remotely from anywhere in the world on your Smartphone or Tablet!
Please remember to change your password in the Advanced Setting-User Setting.
Record your new password here:_________________________________________.
Tips:
1. Please put your smartphone near to the router.
2. Input WiFi SSID and password, click config button, then WiFi setup is finished.
3. When WiFi indicator flash slowly (camera will be in this status after powered-on and hold for 5 minutes),
it means you can start config WiFi. After config is successful, WiFi indicator will flash fast for a while.

Tap the monitoring screen, the video menu action bar will appear.
12 13
Live View Monitoring Options
1 2 3 4 5 6
7 8 9 10 11 12 13 14 15
Cruise Vertically
Cruise Horizontally
Menu
Flip
Snapshot to phone
Record to phone
Listen Off
Talk Off
Contrast
Contract
Brightness
Restore to Default
Resolution VGA/720p/1080p
Mirror
Exit
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
IR LED OFF
Auto
Listen Talk
Set or Call Preset
1. For two-way audio, make the Listen/Talk ON; When talk, please press Hold Talk.
2. Tap Menu you can turn ON/OFF the IR LED and Set or Call Preset (For PTZ camera).

14 15
View from Mac or Windows PC Specifications
Hardware Features
Resolution
Compression / Max Frame Rate
Image Sensor / Lens
Manual Pan / Tilt Range
Motion Detection
Security Protocols
Camera Dimensions
Power Input
10/100Mbps RJ45 Port
WI-FI Support
Power Interface
Reset Button
Built-in SD Socket
Storage Up to 128GB
Built-in Microphone and speaker
3.5mm Audio In / Out Interface
8 infrared LED, 5m Night Vision Range
1920 x 1080, 640 x 360, 320 x 180
H.264/MJPEG, 30fps
1/2.7” CMOS Sensor, f=4.2mm, F=2.0 Viewing Angle: 55°
Horizontal 350°, Vertical 100°
Supported, Will Activate Camera
64/128-bit WEP, WPA/WPA2, WPA-PSK/WPA2-PSK, WPS
111mm x 106mm x 124mm
5V DC, < 6W
Item Description
Install Homeguardcare software for your Mac or Windows PC from the included CD.