Honeywell CT40-WS-PB User manual

-
Arm Mount Sled and Armband
Wearable Solution for Booted CT40
Models CT40-WS-PB, CT40-WS-AB, HWS-ARM BAND,
CT40-WS-00, CT40-WS-KIT
Quick Start Guide
CT40-WS-EN-QS-01 Rev A
1/20



1
Introduction
The Honeywell Wearable Solution allows the user to mount a
booted Dolphin CT40 mobile computer on either arm. It consists
of an arm mount sled and an armband. The sled and armband
can be purchased separately or together as a kit.
Note: HWS-ARM BAND is also compatible with the Dolphin 75
Wearable Solution.
If you ordered additional accessories, verify that they are also
included with the order. Be sure to keep the original packaging
in case you need to return your accessories for service.
CT40 Feature Note
When the CT40 is installed in the arm mount sled, the following
features are not available:
• Internal scanner
• Audio jack pin (select models only)
Part Number Description
CT40-WS-PB Arm mount sled with tethered ring scanner
CT40-WS-AB Armband with wrist pad
HWS-ARM BAND Armband
CT40-WS-00 Kit containing CT40-WS-PB and
CT40-WS-AB
CT40-WS-KIT Kit containing CT40-WS-PB and
HWS-ARM BAND

2
Arm Mount Sled Features
I/O Connector
Ring Scanner
Trigger
Latch
Tab Tab
Finger Ring

3
Armband Features
Strap Clip
Strap Horn
Sled Release Clip Sled Release Clip
CT40-WS-AB
Wrist Pad Arm Pad
HWR-ARM BAND
Strap Horn
Sled Release Clip Sled Release Clip
Strap Horn
Arm Pad

4
Assemble the CT40 Wearable Solution
The illustrations in this procedure assume the sled has not yet
been mounted to the armband. However, the sled can be
mounted to the armband before the user puts the armband on.
Note: The sled requires the use of protective boot CT40-PB-00.
Note: The wearable solution is not compatible with a hand strap.
1. Insert the bottom of a booted CT40 into the bottom of the
sled at an angle.
2. Press the CT40 and sled together firmly until the latch
clicks. If the latch does not engage, verify that the CT40 is
fully seated in the bottom of the sled.
2
1

5
3. Place the armband on top of either arm.
(Armband CT40-WS-AB shown for illustration purposes.)
4. Buckle the straps around the arm and secure any excess
strap length.

6
5. Align the four tabs on the back of the sled with the notches
on the armband and press down evenly until the assembly
clicks together.
HWR-ARM BAND

7
6. Rotate the ring scanner head to the desired orientation and
insert finger.
Note: The ring scanner cable should not cross under the hand.
7. If the CT40 is awake, it will automatically connect to the ring
scanner. If the CT40 is in sleep mode, tap the power button
or the scan button on the CT40 to wake the device and
connect to the scanner.
Scan a Bar Code with the Scan Demo
Note: For optimum performance, avoid reflections by scanning the bar
code at a slight angle.
1. Swipe up from the bottom of the Home screen to access all
apps.
2. Touch Demos > Scan Demo.
3. Point the ring scanner at the bar code.

8
4. Press the ring scanner trigger.
The decode results display on the screen.
Note: In the Scan Demo app, not all bar code symbologies are
enabled by default. If a bar code does not scan, the correct
symbology may not be enabled. To learn how to modify the
default app settings, see the user guide.
Wrist Position
(Armband and sled not shown.)

9
Remove the CT40 from the Wearable Solution
1. Remove finger from the ring scanner.
2. Press down on the clips on both sides of the armband to
release the sled. (Armband CT40-WS-AB shown for
illustration purposes.)
3. Lift the sled out.
2
1

10
4. Press down on the latch on the back of the sled to release
the CT40.
5. Lift the CT40 out of the sled.
6. To remove the armband, loosen the straps to remove the
assembly from the arm. It is not necessary to remove the
straps from the buckles.
1
2

11
Armband Maintenance
The armband can be cleaned between uses with a non-abrasive,
damp cloth and a mild dish soap solution. Be sure to remove the
sled from the armband before cleaning the armband. Allow the
armband to air dry completely before use.
Support
To search our knowledge base for a solution or log into the
Technical Support Portal and report a problem, go to
www.hsmcontactsupport.com.
Documentation
Product documentation is available at www.honeywellaidc.com.
Limited Warranty
For warranty information, go to www.honeywellaidc.com and
click Resources > Product Warranty.
Patents
For patent information, see www.hsmpats.com.
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make
changes in specifications and other information contained in
this document without prior notice, and the reader should in all
cases consult HII to determine whether any such changes have
been made. The information in this publication does not
represent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or
omissions contained herein; nor for incidental or consequential
damages resulting from the furnishing, performance, or use of

12
this material. HII disclaims all responsibility for the selection
and use of software and/or hardware to achieve intended
results.
This document contains proprietary information that is
protected by copyright. All rights are reserved. No part of this
document may be photocopied, reproduced, or translated into
another language without the prior written consent of HII.
Copyright © 2020 Honeywell International Inc. All rights
reserved.