Hoover HV-C60OV-2 User manual

Model Number: HV-C60OV-2
60 cm Electric Oven
INSTRUCTION MANUAL
E209
AFTER SALES SUPPORT
(AU) 1300 886 649 (NZ) 0800 836 761

2After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Contents
03 General Safety Instructions
08 Product Overview
10 Installation
13 Getting Started
14 Instructions
23 FAQs and Troubleshooting Guide
25 Other Useful Information

3
3
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
General Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
Read this manual thoroughly before first use, even if you are familiar with this type
of product. The safety precautions enclosed herein reduce the risk of fire, electric
shock and injury when correctly adhered to. Keep the manual in a safe place for
future reference, along with the completed warranty card and purchase receipt. If
applicable, pass these instructions on to the next owner of the appliance.
Always follow basic safety precautions and accident prevention measures
when using an electrical appliance, including the following:
Installation
Position
• Any adjacent benchtop surfaces, panels, laminates and adhesives must be
made of heat-resistant material. Cabinets with a veneer exterior must be
assembled with glues that can withstand a temperature of at least 120°C.
Plastics or glues that cannot withstand such temperatures will melt and deform
the unit. We accept no responsibility for any damage caused by the appliance
being installed in contravention of this temperature requirement.
• Keep combustible materials, such as curtains, drapes, furniture, pillows,
clothing, linens, bedding, paper, etc., at least 90cm from the front, sides and
rear of the oven.
• The appliance must NOT be installed:
* Behind a decorative door (in order to avoid overheating).
* Next to curtains or soft furnishings (in order to reduce a fire hazard).
* In an area where petrol, paint or other flammable liquids or their associated
vapours may be present (in order to reduce a fire hazard).
WARNING! Professional Installation Only!
This oven must be correctly installed and earthed by an
appropriately qualified installer (licensed electrician) in
accordance with all applicable rules and regulations and following
the instructions in this manual.
Ensure to make these instructions available to the installer. Installation
safety advice is provided below and on the following pages of this
manual; detailed instructions and illustrations start on page 10.
Do not try to install the oven yourself; doing so will expose you to danger
and void the warranty. Improper installation, adjustment, alteration or
service can cause injury or damage. We decline any responsibility for
injury or damage, to persons or property, as a result of improper use or
installation.

44After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
General Safety Instructions (Cont.)
Electrical connection
• Ensure there is an earthed socket nearby.
• A dedicated power circuit is recommended for the unit but not required.
Additional electrical appliances on the same circuit may exceed the current
(amperage) rating for that circuit. If after the installation of your oven the
circuit breaker trips or the fuse fails on a repeated basis, then a dedicated
circuit will likely be required.
• The unit’s power cord must be connected to a properly grounded and
protected, 240V~ electrical outlet. Always use ground fault protection where
required by the electrical code.
• The mains socket must be within easy reach so that the plug can easily be
removed if necessary.
• After installation the appliance must be able to be disconnected by an
accessible plug or a switch in the fixed wiring.
• The outlet voltage and circuit frequency must correspond to the voltage
stated on the appliance rating label.
Power cord
• To reduce the risk of fire, avoid running the power cord under rugs, carpets,
etc. Keep it away from high traffic areas where it may pose a tripping hazard.
• Do not allow electrical fittings or cables to come into contact with areas on
the oven that get hot. Do not let the cord touch hot surfaces during use. Do
not kink, squash or strain the power cord and protect it from sharp edges
and heat.
• Regularly check the power cord for damage. If the supply cord is damaged,
it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard or injury.
• Do not connect the appliance to an extension cord or plug adaptor, which
may overheat and cause a fire.
• If winding the power cord, avoid tight bends as this could damage the cord.
Ventilation requirements
• Heat, steam and moisture will be created during use of the oven. Take care
to avoid injury and ensure the room is adequately ventilated.
• If the appliance is going to be used for prolonged periods of time, additional
ventilation may be required. If in doubt about your ventilation requirements,
consult your qualified installer.
• To reduce the risk of fire, do not install this oven in an area where the
ventilation or circulation ducts may become blocked.

5
5
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
General Safety Instructions (Cont.)
General usage conditions and restrictions
• Domestic use only: This oven is designed for indoor domestic use only. It
can be built into a standard kitchen cabinet or housing unit.
• Intended purpose: This oven is not intended for commercial, industrial
or trade use. Only use this oven for its intended purpose, in its intended
environment and as described in this manual. Any other use may cause fire,
electric shock or injury.
• Follow instructions: Make sure to observe all rules and provisions in
this instruction manual. Do not allow anybody who is not familiar with the
contents of this manual to operate the oven.
• Use common sense: These instructions are not intended to cover every
possible condition and situation. As with any electrical household appli-
ance, common sense and caution are therefore always recommended
when installing, operating and maintaining the oven.
• Usage restriction: This oven is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack of ex-
perience and knowledge, unless they have been given supervision or instruc-
tion concerning use of the appliance by a person responsible for their safety.
• Children: Supervise children to ensure they do not play with the appliance.
Close supervision is necessary when any appliance is used by or near
children. As young children do not recognise the risks involved when
using electrical appliances, make sure young children are kept well away
from the oven and not allowed to touch it at any time. If it is necessary for
younger family members to be in the kitchen, ensure that they are kept
under close supervision at all times.
• Unattended: Never leave the oven unattended during use, as this is a fire
risk. Oils and fats in roasting dishes may catch fire due to overheating.
• No heater: Do not use the oven for heating a room or drying clothes.
• No timer: The appliance is not intended to be operated by means of an
external timer or separate remote control system.
• Personal safety: Do not operate the oven unless you are wearing something
on your feet and your hands are dry.
• After use: Make sure to switch off the oven after use and before cleaning.

66After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
General Safety Instructions (Cont.)
• WARNING! Disconnect: Remove the power plug from the electrical socket
in the following situations:
* Before changing the lamp to avoid the possibility of electric shock.
* Before any adjustments, service or maintenance work is done on it.
Grip the plug when disconnecting, do not pull on the cord. Damage: Do
not use the oven if any part has been damaged or does not work properly.
Only have it repaired by an authorised service centre. Incorrect repair
could expose you to the risk of electric shock, fire or injury. Prolonged use
of the unit in such conditions could cause fire or electrocution. In case of
damage, contact our after sales support centre using the details at the
bottom of this page.
• Faults: Do not use the oven in the event of a technical fault. Any faults must
be fixed by an appropriately qualified and authorised person.
• Misuse: We accept no liability for any eventual damages caused by misuse
of the product or noncompliance with these instructions.
Oven-specific safety advice
• Oven door: Do not place heavy objects on the oven door. Do not lean on
the oven door when it is open, as this can damage the door hinges. When
opening the door, always hold the handle in the centre.
• Grill: Keep the oven door closed when using any of the cooking functions,
including the grill function.
• Oven accessories: When removing the baking tray or oven rack from the
hot oven, always use an oven mitt.
• Aluminium foil: Do not use aluminium foil to cover the grill pan or heat items
wrapped in aluminium foil under the grill. The high reflectivity of the foil could
potentially damage the grill element. You should also never line the base of
your oven with aluminium foil.
• Lifting/moving: Do not attempt to lift or move the oven by using the oven
door or handle, as this may cause damage to the appliance or result in
injury to the person lifting the appliance. To lift/move the appliance, use the
recessed handles at the sides of the oven.
• Fan guard: If this is removed for cleaning, make sure the oven is switched
off and has cooled completely before removing the fan cover. Also ensure
that the cover is properly reinstalled after cleaning.

7
7
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
• Cleaning: Clean the oven on a regular basis so oils and fats do not
accumulate and cause a fire risk. Make sure all relevant oven controls are
switched off before cleaning. Refer to pages 25–27 for comprehensive
cleaning instructions.
Do not use harsh abrasive cleaners or sharp metal scrapers to clean the
oven door glass as this can scratch the surface, which may result in the oven
glass shattering.
Do not use a steam cleaner for cleaning any part of the oven.
Ensure that no part is immersed in water or other liquid during cleaning.
The oven must be switched off before removing the fan guard, and after
cleaning, the guard must be replaced in accordance with the instructions.
• Moving: When transporting or storing the unit, keep it in a dry location, free
from dust, excessive vibration or other factors, which may damage the unit.
WARNING! HOT SURFACES!
• The heating elements and other accessible parts of the oven become
extremely hot during use and retain heat after operation.
Do not touch hot surfaces! Keep young children well away during use.
• Take care when handling the food you are cooking to avoid touching hot
parts, such as the heating elements, inadvertently.
• Never add cold water to food on a hot baking tray/oven rack, or directly
onto food in a hot oven. The steam created could cause serious burns or
scalding and the sudden change in temperature can damage the enamel.
• Always use oven mitts when handling food and dishes from the oven.
• Opening the door: Be careful when opening the oven door to avoid
contact with hot parts of the oven and steam.
• Danger of fire! Never leave items inside the oven cavity as this can be a
fire hazard when the oven is switched on.
General Safety Instructions (Cont.)

88After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Product Overview
Scope of delivery
Oven
1 Control panel (see page 9)
2 Oven light (inside oven)
3 Shelf supports (side racks) (inside oven)
4 Removable door
5 Door hinge (inside oven)
1
2
4
3
5

9
9
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Product Overview (Cont.)
Control panel
NOTE: Due to continued product improvement, images and illustrations in this manual
may vary slightly from the product purchased. All images in this manual are for
reference purposes only. Parts are not necessarily pictured to scale.
Control panel
6 FUNCTION control
7 DECREASE button
8 TIMER / OK button
9 INCREASE button
10 Digital Display
11 TEMPERATURE control
Accessories
12 Oven rack
13 Baking tray
14 Baking tray insert (not
shown)
Other inclusions
(not shown)
2 Screws (for installation)
Instruction manual
Quick start guide
Warranty certificate
11
6
12
Accessories
10
13
8
97

10
10 After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Product dimensions Aperture dimensions
Height: 595 mm Height: 600 mm
Width: 595 mm Width: 560 mm
Depth: 575 mm Depth: 570 mm (min.)
Installation
Installing the oven into a kitchen cabinet
Space requirements
• The designated aperture for the oven must be of the size given in Fig. 1,
and must have the ventilation cut-outs shown above (see opposite for more
details on ventilation requirements).
• Kitchen cabinets must be set level and fixed. If installed in a floor cabinet, a
minimum 5 mm gap is required between the appliance and the front panel of
the surrounding cabinet. If installed in a medium high cabinet, no such gap is
required.
• The minimum installed/situated height from floor to the bottom of the oven
shall be 80 mm.
• If there is a drawer underneath the oven, a shelf must be installed between the
oven and drawer.
• The power point for connection to the electricity supply must be in close
vicinity to the installation location but cannot be directly behind the oven as
this would impede the oven sitting correctly in the cabinet.
Fig. 1
Product dimensions Only plus deviations are
admissible for all dimensions.

11
11
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Installation (Cont.)
Ventilation requirements
• When mounted under a benchtop, airflow ventilation is important to help
keep the cabinets and oven electronics from getting too hot.
• The location of the power point cannot be mounted directly behind the
oven as this will impede the oven sitting correctly into the cabinet.
Positioning the appliance
• Before installing the appliance, make sure that the mains plug is
disconnected. Also ensure that the kitchen area is dry and well ventilated.
• This is a built-in oven and its back wall and one side wall can be placed next
to a high piece of furniture or a wall. Coating or veneer used on furniture
must be applied with a heat-resistant adhesive (120°C). This prevents
surface deformation or detachment of the coating.
• Easy access to all control elements should be ensured.
• Make an opening for the oven with the dimensions given in Fig. 1, observing
all required clearances for ventilation.
• Insert the oven completely into the opening. To secure it, open the oven
door and locate the two fixing holes in the frame. Screw the two installation
screws through the oven frame into the housing unit (Fig. 2).
Fig. 2

12
12 After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Installation (Cont.)
IMPORTANT!
• Do not use the oven door or handle to lift or move the oven, use the slots located
at both sides.
• Carry the appliance with at least one other person.
• Once the oven has been fully installed, all electrical parts must be completely
insulated. This is a legal safety requirement. All guards must be firmly fixed into
place so that it is impossible to remove them without using special tools.
Electrical connection
WARNING! All electrical work must be carried out by a licensed electrician.
No alterations or wilful changes in the electricity supply should be carried out.
• This oven is manufactured to work with single-phase alternating current
(220–240 V~ 50–60 Hz).
• If the power cord is damaged, it must only be replaced by an authorised
technician.
• Means for disconnection must be incorporated in the fixed wiring in
accordance with the wiring rules.

13
13
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Before first use
• Read: The best way to familiarise yourself with all the parts and operating
principles of your new electric oven is to read this manual. Pay particular
attention to the safety instructions on pages 3–7. Refer to pages 8–9 for an
illustration and list of all parts and buttons.
• Initial use: After the appliance has been properly installed, and before first
use, you should burn off any dust, oil or other remnants that may have been
left from the manufacturing process or transport.
Take out any oven fittings (shelf supports), open a window or switch on
any ventilation in the room. Heat the oven in manual cooking mode to a
temperature of 200°C following the instructions on the next pages. Leave
the oven on for 15 minutes, or until no more odour or smoke is present. We
recommend you leave the room during this burning off process. However,
any smoke and odour development during this initial use is normal and
completely harmless; ensure good ventilation.
• Clean: After the oven cavity has cooled, wipe the interior and exterior oven
surfaces with a soft cloth dampened with warm water and a little mild
detergent. Do not use abrasive cleaners.
• Wash: Remove and wash the oven rack and baking tray with warm water
and a little washing-up liquid. Dry and return to the oven. Leave the oven
door open until it is completely dry.
CAUTION!
Take care to avoid burns, the oven becomes very hot during use.
Getting Started
Unpacking the appliance
• This product has been packaged to protect it against transportation damage.
Unpack the appliance and remove all packaging materials from around the
oven and from inside the oven cavity.
• Keep the original packaging carton and materials in a safe place. It will help
prevent any damage if the product needs to be transported in the future, and
you can use to store the appliance, if required.
• The carton is recyclable. Whenever possible, reuse the carton and recycle it
when disposing of the packaging materials.
• Plastic wrapping can be a suffocation hazard for babies and young children, so
ensure all packaging materials are out of their reach and disposed of safely.

14
14 After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Instructions
Selecting an oven function
• Use the FUNCTION control knob to select your required oven function. (Please
refer to the table opposite for a description of the functions.) The appliance will
utilise different elements within the oven cavity depending on the oven function
selected.
Setting a temperature
• Use the TEMPERATURE control knob to set the required temperature for
cooking or baking in the oven, turning the knob in clockwise direction. The
temperature can be regulated within a range of 50–250°C.
• Unless your recipe states otherwise, always wait until the oven is hot
before placing food inside the oven chamber. The oven has reached the set
temperature when the thermostat light goes out for the first time.
• When the oven is not in use, make sure the TEMPERATURE knob is in the OFF
[o] position.
IMPORTANT: For the oven to start cooking, you have to set the function and
temperature as well as the timer – or set the timer to Manual cooking mode
(see pages 16-19).
IMPORTANT!
Setting the function and temperature does NOT switch on the oven. You must
set the timer as well (or set it to manual mode) for the oven to switch on.
Switching the oven on and off
• To switch on the oven you need to set the required oven function and
cooking temperature and timer (or manual) mode.
• To switch off the oven, set both FUNCTION and TEMPERATURE control
knobs to the OFF [ o ] position.
Selecting a function and temperature
FUNCTION
TEMPERATURE
Fig. 3

15
15
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Symbol Function / cooking mode
Oven light
This function provides a separate light control to illuminate
the oven cavity without opening the door. It will light up for all
cooking functions.
Defrost
This function circulates room temperature air to thaw frozen
food more quickly, without the use of any heat. It is a gentle yet
effective way to speed up the defrosting process.
Grill
This cooking method uses the inner part of the top heating
element to grill the food.
Grill with Fan
This cooking method uses the inner and outer parts of the top
heating element and the fan to grill larger quantities of food. It
is recommended for grilling meat.
Convection
This function uses warm air, created by the rear heater, evenly
distributed throughout the oven by means of the fan. It allows
food on different shelves to be cooked more evenly.
Instructions (Cont.)

16
16 After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Setting the timer
Your new electric oven has a digital timer with an easy to read LED display
and three push buttons for easy operation (Fig. 4).
Instructions (Cont.)
Timer functions
When the timer is in standby mode, you can set the oven to manual cooking
mode, or to various automatic timer functions (minute minder, duration, end
cooking, delayed cooking).
• To select a timer function: press the [ ] button, repeatedly, then use the
[ + ] or [ – ] button to set the desired point or period of time.
• To set the time: press the [ + ] or [ – ] button briefly for minute-to-minute
progression, or press and hold to move quickly through the digits.
Setting the clock
When your new oven is connected to the mains supply for the first time, the
display shows 12.30 while 12 is blinking.*
Before you start using the oven, you should set the clock. Please note that
this oven is equipped with a 24 hour clock, which means, for example, that
2pm will be displayed as 14.00.
• While 12 is blinking on the display, press the [ + ] or [ – ] button to set up the
hour, then press [ ] to confirm.
• Press the [ + ] or [ – ] button to set up the minutes, then press [ ] to finish
clock setting.
• The time of day has now been set and the timer is in standby mode.
* NOTE: If the numbers on the display are not blinking, or if you want to adjust
the clock during normal use, press the [ + ] and [ – ] buttons simultaneously and
hold for three seconds. Then adjust the time as described above.
DISPLAY
DECREASE INCREASE
CONFIRM
Fig. 4

17
17
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Instructions (Cont.)
• To cancel a setting and enter Manual cooking mode:
press the [ ] button and hold it for more than three seconds.
• To cancel the setting and return the timer to standby mode:
press the [ ] and [ + ] buttons simultaneously and hold for three seconds.
• If there is no operation for five minutes during timer setting, it will return to
Manual cooking mode.
Manual cooking mode
• Place the food to be cooked in the oven, close the door and set the
cooking function and oven temperature.
• Press and hold the [ ] button for more than three seconds to enter Manual
cooking mode. The display shows the clock time and the cooking icon.
• To start the oven, set the oven function and temperature.
• When you have finished cooking, turn the FUNCTION and TEMPERATURE
controls to the OFF [ o ] positions.
• The oven is now in Manual cooking mode. To return the timer to standby
mode, press the [ ] and [ + ] buttons simultaneously and hold for three
seconds.
NOTE: To ensure the oven is not left on accidentally in Manual cooking mode,
when no button has been pressed for five hours, the timer will flash once per
second to warn you the oven will enter standby mode. After a total of 10 hours,
the timer will enter standby mode.
Setting the minute minder
You can set a period of time using the minute minder function and an alarm will
sound when that period of time has elapsed. You can set the minute minder at
any time, regardless of whether you are using the oven to cook.
• Press and hold the [ ] button for more than three seconds until is shown.
• Press the [ ] button again, briefly, to enter Minute minder mode. The
display shows the clock at the current time and the minute minder icon.
• Use the [ + ] and [ – ] buttons to set the desired time period, then press [ ]
to confirm. An alarm will sound when the countdown time has elapsed.
Press any button briefly to silence the alarm.
• This function will NOT switch off the oven. To switch off the oven you must
turn the FUNCTION and TEMPERATURE controls to the OFF [ o ] positions.
• Press the [ ] and [ + ] buttons simultaneously and hold for three seconds
to return the timer to standby mode.

18
18 After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Setting the cooking duration [dur]
This function allows you to set a countdown time (max. 10 hours) after which
the oven turns off automatically.
• Place the food to be cooked in the oven, close the door and set the
cooking function and oven temperature.
• Press and hold the [ ] button for more than three seconds until is shown.
• Briefly press the [ ] button again, twice, to enter Duration mode. The
display shows the duration [ dur ] and cooking icons.
• Use the [ + ] and [ – ] buttons to set the desired cooking period, then press
[ ] to confirm. The oven will start operating and the display shows the
clock at the current time, the cooking icon and [ A ].
• When the cooking time has elapsed, the oven will stop heating, the symbol
[ A ] will start blinking on the display and an alarm will sound. Press any
button briefly to silence the alarm.
• Turn the FUNCTION and TEMPERATURE controls to the OFF [ o ] positions.
Instructions (Cont.)
Setting the end cooking time [End]
This function is similar to the cooking duration function. However, instead of
setting the period of time that you wish the oven to switch off after, you select
the point of time (the time of day) at which you want the oven to switch off.
• Place the food to be cooked in the oven, close the door and set the
cooking function and oven temperature.
• Press and hold the [ ] button for more than three seconds until is shown.
• Briefly press the [ ] button, repeatedly, until [ End ] is displayed on the
screen, together with the cooking icon.
• Use the [ + ] and [ – ] buttons to set the desired end cooking time (time
of day), then press [ ] to confirm. The oven will start operating and the
display shows the clock at the current time, the cooking icon and [ A ].
• When the end of the cooking time has been reached, the oven will stop
heating, the symbol [ A ] will start blinking on the display and an alarm will
sound. Press any button briefly to silence the alarm.
• Turn the FUNCTION and TEMPERATURE controls to the OFF [ o ] positions.

19
19
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Setting fully automatic delayed cooking
The delayed cooking function is a convenient feature you can use when you
are at home and want to set the oven to come on at a time in the future and
switch off after a set cooking duration. It only works after you have set the
cooking duration function.
• Place the food to be cooked in the oven, close the door and set the cooking
function and oven temperature.
• Press and hold the [ ] button for more than three seconds until is shown.
• First, briefly press the [ ] button again, twice, to enter Duration mode. The
display shows the duration [ dur ] and cooking icons. Use the [ + ] and [ – ]
buttons to set the desired cooking period, then press [ ] to confirm. The
display shows [ A ] and the cooking icon.
• Second, keep pressing the [ ] button until [ End ] is displayed on the
screen. Use the [ + ] and [ – ] buttons to set the desired end cooking time, then
press [ ] to confirm. The display shows the clock at the current time and the
symbol and [ A ]. The cooking icon will disappear until the time when the
oven starts operating.
• The oven will start operating at the time calculated by deducting the cooking
period from the set finishing time, and will stop at the set finishing time. The
symbol [ A ] will begin to flash and an alarm will sound. Press any button briefly
to silence the alarm.
• Turn the FUNCTION and TEMPERATURE controls to the OFF [ o ] positions.
• Press the [ ] and [ + ] buttons simultaneously and hold for three seconds to
return the timer to standby mode.
• NOTE: Once delayed cooking has been set, times cannot be changed. To
change a setting, you have to cancel the program first and then reset it.
• To cancel a setting, press and hold the [ ] button for more than three seconds.
Instructions (Cont.)
WARNING!
• For your personal safety and to avoid any potential fire risk, do NOT use the
delayed cooking function and then leave the oven unattended.
• For food safety reasons, do NOT leave easily spoilt foods in the oven for too
long when using the delayed cooking function.
• When baking, we recommend you do NOT use the delayed cooking function
as the cake mixture may dry out and the raising agents may lose their
effectiveness.

20
20 After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Shelf positions
• Your electric oven comes supplied with an oven rack and a baking tray,
which can be positioned on the side racks (shelf supports) at the sides of
the oven cavity (Fig. 5).
• When installed correctly, the oven rack and baking tray should be
horizontal and not at an angle. Ensure that you select a shelf position at the
same height on both sides of the cavity.
• Using the oven rack: The oven rack has safety stops to prevent accidental
withdrawal. After engaging the oven rack into the shelf supports, as you
push the oven rack into the oven, lift the front of the rack slightly to bypass
the stops and allow the oven rack to slide fully into the shelf supports.
• Removing the oven rack: Gently pull the oven rack outwards. When it
stops, lift the front slightly to bypass the safety stops and then completely
withdraw the oven rack from the oven.
• Shelf supports: If you are cooking food in a large roasting dish, you can
remove the shelf supports and place the dish on the floor of the oven
cavity.
Instructions (Cont.)
Fig. 5
OVEN RACK
BAKING TRAY
SHELF SUPPORT