
2
GB
Installation
Connection of the water supply
To carr this out, use the kit provided which contains all
the necessar elements for connection to the water
suppl .
To improve the performance of the Aqua Care, we
recommend that ou fit a tap with a filter on the pipe for
the connection to the water s stem: in this wa it will be
possible to manuall interrupt the water suppl during
long periods in which Aqua Care is not used.
! The water pressure inside the water s stem must be
between 0.8 bar and 8 bar.
! The appliance must onl be connected to a water
suppl suitable for drinking.
Your appliance is supplied with a 13amp fused plug that
can be plugged into a 13amp socket for immediate use.
Before using the appliance please read the instructions
below.
WARNING:
THI APPLIANCE MU T BE EARTHED.
Replacing fuse covers:
When replacing a fault fuse, a 13amp ASTA approved
fuse to BS 1362 should alwa s be used and the fuse
cover re-fitted.
If the fuse cover is lost, the plug must not be used until
a replacement is obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the
correct colour as indicated b the coloured marking or the
colour that is embossed in words on the base of the plug.
Changing the plug:
Removing the plug
If our appliance has a non-rewireable moulded plug
and ou should wish to remove it to add a longer cable
or to re-route the mains cable through partitions, units
etc. please ensure that either:
- The plug is replaced b a fused 13amp re-
wireable plug bearing the BSI mark of
approval.
or
- The mains cable is wired directl into a
13amp cable outlet, controlled b a
switch (in compliance with BS 5733)
which is accessible without moving the
appliance.
! Before placing our new appliance into operation
please read these operating instructions carefull . The
contain important information for safe use, for installation
and for care of the appliance.
! Please keep these operating instructions for future
reference. Pass them on to possible new owners of the
appliance.
Positioning an connection
Positioning
1. Place the appliance in a well-ventilated humidit -free
room.
2. Do not obstruct the rear fan grills. The compressor and
condenser give off heat and require good ventilation to
operate correctl and save energ .
3. Leave a space of at least 10 cm between the top part of
the appliance and an furniture above it, and at least 5 cm
between the sides and an furniture/side walls.
4. Ensure the appliance is awa from an sources of
heat (direct sunlight, electric stove, etc.).
5. In order to maintain the correct distance between the
appliance and the wall behind it, fit the spacers
supplied in the installation kit, following the
instructions provided.
Levelling
1. Install the appliance on a level and rigid floor.
2. If the floor is not perfectl horizontal, adjust the
refrigerator b tightening or loosening the rear feet.
Electrical connections
After the appliance has been transported, carefull
place it verticall and wait at least 3 hours before
connecting it to the electricit mains. Before inserting
the plug into the electrical socket ensure the following:
The appliance is earthed and the plug is compliant
with the law.
The socket can withstand the maximum power of the
appliance, which is indicated on the data plate
located inside the freezer (e.g. 150 W).
The voltage is in the range of values indicated on the
data plate located inside the freezer (e.g. 220-240V).
The socket is compatible with the plug of the appliance. If
the socket is incompatible with the plug, ask an authorised
technician to replace it (see Assistance). Do not use
extension cords or multiple sockets.
! Once the appliance has been installed, the power
suppl cable and the electrical socket must be easil
accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularl and replaced b
authorised technicians onl (see Assistance).
!The manufacturer declines any liability should
these safety measures not be observed.