Hydrofarm Active Aqua AASFT48 User manual
INSTRUCTIONS
AASFT48
AASLH48
AASLP48
UNIVERSAL TRAY STAND - LARGE
INSTRUCTIONS
www.Hydrofarm.com
2
BOTTOM STAND PARTS LIST
A- Corner Leg standard height w/casters V1 (2)
B- Side Rail (4)
C- Center Leg standard height w/casters (2)
D- Center Rail Top (2)
E- Corner Leg standard height w/casters V2 (2)
F- End Rail (2)
G- 2-Piece Center Support Rail (2)
H- Corner Retainer V2 (2)
I- Corner Retainer V1 (2)
J- 2-Piece Center Leg Support Bar (1)
WHAT’S IN THE BOX
Figure 1
INSTRUCTIONS
ASSEMBLY INSTRUCTIONS (FOR BOTTOM STAND ONLY):
NOTE: If you are adding a Light Hanger to your boom stand, STOP HERE and connue the
assembly using the secon below tled ASSEMBLY INSTRUCTIONS (INCLUDING LIGHT HANGER).
INSTRUCTIONS
www.Hydrofarm.com
4
NOTE: Be sure to install the Corner Legs V1 at two opposite corners from each other, and the
Corner Legs V2 at the two remaining opposite corners. They must be installed this way or the
assembly will be incorrect.
Retainers V1 at opposite corners and the Corner Retainers V2 at opposite corners)(see Figure 1 to
see the proper relave angles of all four corner retainers at once
INSTRUCTIONS
5
ASSEMBLY INSTRUCTIONS (INCLUDING LIGHT HANGER)
LIGHT HANGER PARTS
LIST
A1
B1 - Trellis Bar (2)
C1
D1
E1 - Center Light Bar (1)
F1 - Lynch Pin (4)
INSTRUCTIONS
www.Hydrofarm.com
INSTRUCTIONS
INSTALLATION OF THE LOW PROFILE LEG KIT
NOTE: The below instrucons assume that you have already used the standard sized legs and are
switching to the low prole legs. If you want to assemble the stand with the low prole legs from
the start, simply use the Low Prole Corner Legs V1 and Low Prole Corner Legs V2 in place of the
standard length corner legs when assembling the boom tray stand. Be sure to install the Low Prole
Corner Legs V1 at two opposite corners from each other, and the Low Prole Corner Legs V2 at the
two remaining opposite corners. They must be installed this way or the assembly will be incorrect.
NOTE: This stand can also be easily adjusted to accommodate both 4' x 6' and 3' x 6' size ood
tables. To adjust for 4' x 6' tables, depress the spring buons on either end of the Side Rails (Part
B) and slide (collapse) the side rails all the way toward the corners unl the spring buons lock
in the innermost holes in the Corner Legs. This will reduce the length of the stand from 8' to 6'.
To adjust the stand for 3' x 6' tables, adjust to reduce the stand’s length to 6' as just described
above, and then also collapse the End Rails (Part F) completely on both sides in the same
manner, which will reduce the tray stand’s width from 4' to 3'.
8
www.Hydrofarm.com
www.Hydrofarm.com
WARRANTY
LIMITED WARRANTY
Hydrofarm warrants the AASFT48, AASLH48, AASLP48 to be free from defects in materials and
AASFT48, AASLH48,
AASLP48
AASFT48, AASLH48, AASLP48
GARANTIE LIMITÉE
AASFT48, AASLH48, AASLP48 ne présente aucun défaut de pièces et main-
AASFT48, AASLH48, AASLP48
AASFT48, AASLH48, AASLP48
GARANTÍA LIMITADA
AASFT48, AASLH48, AASLP48
AASFT48,
AASLH48, AASLP48
AASFT48, AASLH48, AASLP48
AASFT48, AASLH48, AASLP48 Instrucons revised - May 5, 2017 4:19 PM
This manual suits for next models
2
Table of contents
Other Hydrofarm Rack & Stand manuals
