Griffin Technology B80 User manual

www.Griffin-Stands.com
Cymbal Boom
Stand
www.Griffin-Stands.com
www.Griffin-Stands.com
Griffin™ stands and accessories are manufactured
in several innovative factories responsible for
developing products that address the newest
needs and trends of the current market. We take
pride in the Griffin™ brand and endeavor to be on
the forefront of the musical stands and musical
and lighting accessories market.
Performance Issue, Uneven or Unstable- Make
sure all nuts and bolts are tight on the product. If they
are, then loosen all nuts and bolts 1 full turn counter-
clockwise, then go back and tighten each bolt only ½
turn tight. Then do a final tighten turn for another ½
turn tight. Next, Make sure there are not any missing
nuts or bolts. Third, ensure all parts on the product
are not broken or defective. Finally, Re-read the
assembly instructions or watch the product
demonstration video to ensure you have correctly
assembled or are using the product properly with
factory specifications.
Missing Parts- The pictures, videos and images
shown in this manual might have changed style or
count due to the product being redesigned. So in rare
cases the part may no longer be included or of a
different style. However, if you think you are missing
a part that is necessary to the assembly and use of
your product, then first carefully double check all
packaging for any parts you think are missing. Some
parts might be hiding in the packaging or loose in an
inner box.
User Manual
M o d e l # B 8 0
Griffin | 11408 Hwy 64 W, Tyler, TX 75704 |
[email protected] | www.Griffin-
Stands.com
For current product specifications, please to go
www.griffin-stands.com and type the model number
into the search bar. Locate the product listing to view
the current factory specifications. Thank you for purchasing the Griffin Cymbal Boom
Stand. Your product comes with a 1 year factory
warranty from purchase date. Please read all
assembly instructions prior to assembling your new
cart. Pictures that may aid in assembly can be found
by going to www.griffin-stands.com and typing B80
into the search bar.

Step 4 –At the tip of the boom arm is a pivot point with
another gear teeth which can be adjusted to your
preferred angle by turning the knob loose and tightening
once the desired angle is reached. Remove the top
cymbal felt by unscrewing the knob and place your
cymbal and place the top cymbal felt with the washer on
top as seen on Figure 6. This type of cymbal stand
comes with a counter weight that can be removed,
however removing this may cause for the stand to tilt
forward.
Step 1 –Take the tripod section of the stand and
spread the legs by using two (2) hands and tighten the
knob to secure the legs (See Figure 1) Please note that
under extension of the tripod legs may cause instability
while over extension may cause stand failure.
Step 2 –Unscrew the knob on
the top of the tripod stand and
inset the chrome middle section
all the way down (make sure
that the middle pipe is straight
down and use force if resistance
is felt while inserting the pipe).
Adjust the length of the chrome
pipe you inserted and use the
screw to secure the height of
the stand as shown in Figure 2
and 3. With this you can use the
included memory lock and
adjust it to your preferred
height. Please scan the QR Code below for the product
demonstration video. Or go to the URL shown here and find
the product video. www.Griffin-Stands.com/Videos
Step 3 –Take the boom
arm align the teeth
against the top of the
middle section, also add
pressure since the
spring needs to be in the
center and use the
turning knob to tighten.
Once this is in place the
boom arm can be
adjusted (See Figure 4
and 5)
Step 6 –For safety reasons, please always make sure to
test the stability and safety of the product before use.
Double check all nuts and bolts, knobs and connectors,
make sure that these are tight and securely fastened
before use of your product. Test the product under light
use or light loads the first time to confirm assembly and
structure of the product is correct.
Step 5 –To ensure stability make sure the front of the
boom is placed over a leg of the tripod. This type of
cymbal stand comes with a counter weight that can be
removed, however removing this may cause for the stand
to tilt forward. If your stand is wobbly or unstable, make
sure that the legs are spread wide or adjust the boom
arm the opposite way and bring down the height.