Ibera IB-ST20 User manual

Hanger folded Hanger erected
Determine Mounting Height
Mark Mounting Height
A = Distance from rear of bike to
upper bracket centre hole
B = Distance between floor
and rear tyre
C = A+B: Mounting height
Parts
a Upper bracket
b Wheel holder
c Brace
d Brace recess
e Lower bracket
f Rear wheel rest
g Wall plugs (screw anchors) x 5
(for masonry or concrete walls only)
h Screws x 5
Tools Required
Tape measure
Stud finder (for drywalls or wooden panel walls)
Spirit level (optional)
Drill
Drill bit
Phillips head screwdriver
Hammer (if wall plugs are used)
Warning
Do not mount hanger on drywalls (plasterboard), or wooden panel walls unless there is a wooden stud behind it. Use drill bit of
appropriate size and type: e.g. masonry drill bit for masonry. Avoid any electrical, plumbing, or water fittings hidden in or behind walls.
If you lack the DIY skills to install hanger, seek professional help.
警告(繁體中文) 1、請勿將本產品鎖固在沒有支撐的牆壁、石膏板或裝飾板上。2、磚塊或水泥牆請使用6.5mm的鑽頭鑽孔。3、安裝時請避開電子電路，
瓦斯、天然氣或自來水的管線。4、吊掛自行車前，請確認本產品有確實地安裝在實心柱子、樑或牆上，以避免對人和自行車造成損傷。5、如果您缺乏DIY技
能安裝，請尋求專業幫助。
www.ibera.info
USER MANUAL
Roll-On Bicycle Wall HangerRoll-On Bicycle Wall Hanger
Storage or display rack.
Max. Load 18 kg / 39.5 lb. (最大載重18 kg)
fgh
Compatibility
Wheel size: 20–29".
Tyre Width: 2.3–6.3 cm (0.9–2.5").
Not suitable for bikes with mudguards (fenders).
Width: 2.3–6.3 cm (0.9–2.5").
Tyre
fig. 1 fig. 2
a
b
c
d
e
Mount Front Wheel Bracket
Mount hanger on a solid wall, or along wall stud (upright timber) of a
plasterboard wall (drywall). Mount in a place with adequate space
where it is unlikely to cause obstruction, be knocked or bumped, or
interfered with by young children. Determine correct height for hanger
(rear tyre should sit between 5 cm (2") and 10 cm (4") off floor or ground),
and make sure it is in a straight vertical position (fig. 4).
Erect hanger by fitting brace into brace recess (fig. 2). Determine Mounting Height: put hanger on floor, brackets facing down. Place
bike's front wheel in hanger. Move hanger and bike so rear wheel is nearly touching wall (fig. 3). Hold bike, place your foot on lower
bracket to keep it in place, lift front of bike and shift it slightly rearward until front tyre makes contact with the 2 touch points on wheel
holder. (fig. 3b), and rear wheel is touching the wall. Mark centre hole in upper bracket with a pencil (fig. 5b). Then measure distance
from wall to mark on floor (A). To this measurement add 5 to 10 cm (B). Mark Mounting Height (C = A+B): the position of hanger's
upper bracket centre drill hole on wall (measured from floor) (fig. 4). Fold hanger before mounting on wall.
Mount HangerMount Hanger
fig. 4
Wall
Min. height 5 cm (2") – 10 cm (4")
Rear wheel
rest
C
Floor
fig. 3a
Wall
Floor
C
A
B
Instructions
fig. 3b
Hold tyre against 2 wheel
holder touch points
1
2

Ibera Co. Ltd.
Specifications subject to change without notice. Ibera is a trademark
of Ibera Co. Ltd. All other trademarks are property of their respective
owners. Copyright Ibera Co. Ltd. Made in Taiwan. IB-ST20
See other Ibera products at www.ibera.info
Artwork: 12/22
Ibera warrants this product for normal usage against workmanship, and material
defects to the original purchaser for two year from purchase date. Products
purchased online are not covered by this warranty unless purchased from an
authorised Ibera online store. 1. User assumes all risk of personal injury,
damage to or failure of the product when it is used in jumping, acrobatics or
similar activities. 2. Warranty does not cover any incidental or consequential
damages, such as personal injury or other losses due to accident, neglect,
misuse, abuse, modification, normal wear and tear, improper care and cleaning,
or failure to follow included instructions.
Limited Warranty
www.ibera.info
USER MANUAL
Roll-On Bicycle Wall HangerRoll-On Bicycle Wall Hanger
Storage or display rack.
fig. 7
Side-swing design
Wall
Note
• If bike is properly hung, pedal should not touch wall, but if bike is swung too far or bumped, pedal might make contact with wall.
To avoid wall damage, consider installing protection on the wall.
• After hanger is installed, it may not be compatible with other bikes of different size.
Mount Rear Wheel Rest
Mark a cross on the wall at the intersection of the centre of the rear wheel hub and the vertical centreline of front wheel brackets (fig. 6).
Remove bike from hanger. Position centre of rear wheel rest at the centre of your marked cross. Mark 2 drill holes: For drywalls or
wooden panel walls, use inner holes (fig. 5a). For Masonry or Concrete Walls, use outer slots (fig. 5b). Drill holes and fix screws in place.
Bike can be swung to the side to save space (fig. 7). When
hanging bike on the left side, seat rear wheel on left side of
wheel rest; vice versa for the right side.
Storing BikeStoring Bike
Unfold hanger, fit brace securely in brace recess. With wheel holder facing straight out from wall, lift the bike vertically from the handlebars
so front wheel is standing up. Align front wheel with wheel holder and roll on hang bike–lift the bike slightly if necessary (fig. 4).
Hang BikeHang Bike
Warning: Hanger must be mounted securely on a wall stud (one of
the vertical lengths of timber behind the wall). Use a stud finder to
locate stud, and mark its centreline with a pencil. Place the brackets
on wall with stud centreline between the upper bracket centre hole
and right hole. In upper bracket, mark 2 drill holes in centre and right
(left hole is not used). In lower bracket, mark 1 drill hole in centre (left
and right holes are not used). (fig. 5b). Drill holes. Fasten brackets
firmly with screws (fig. 5a).
Drywalls or Wooden Panel Walls
石膏板或木板的支撐柱
fig. 5a
In upper bracket, mark 2 drill holes in left and right (centre
hole is not used). In lower bracket, mark 1 drill hole in
centre (left and right holes are not used). (fig. 5b). Drill
holes with a 6.5 mm (1/4") drill bit. Install 3 wall plugs with
hammer, making sure they are firmly pressed in. Fasten
brackets firmly with screws (fig. 5c).
Masonry or Concrete Walls
磚塊或水泥墻
Left hole
Centre hole
Right hole
fig. 5b
fig. 6
Left side Right side
Correct rear wheel
rest position
fig. 5c
Drill holes
(6.5 mm diameter)
Drill holes