Stealth Products GAT472P-M User manual

Install Manual
Mounting Hardware
GAT472P-M
IDM-ALLROUND-9/IDM-ARLITE-9 Gatlin Mount
For GAT400 Series Mounts
INSTALLATION INSTRUCTIONS FOR
Stealth Products: IDM-ALLROUND-9
IDM-ARLITE-9
Mo-Vis: P002-71 All Round Joystick
P002-72 All Round Lite Joystick

i
Customer Satisfaction 1.0
Stealth Products strives for 100% customer sasfacon. Your complete sasfacon is
important. Please contact us with feedback or suggested changes that will help
improve the quality and usability of our swing away hardware. You may reach us at:
Stealth Commitment 1.1
Installation Date:
Dealer:
Dealer Stamp:
Serial Number:
MDSS GmbH
Schiffgraben 41
30175 Hannover, Germany
Stealth Products, LLC
104 John Kelly Drive, Burnet, TX 78611
Phone: [phone] Toll Free: 1(800) 965-9229
Fax: [phone] Toll Free: 1(800) 806-1225
[email protected] www.stealthproducts.com

ii
Warning Labels 2.0
Warning Labels 2.1
Warnings are included for the safety of the user, client, operator and property. Please
read and understand what the signal words SAFETY, NOTICE, CAUTION, WARNING
and DANGER mean, how they could affect the user, those around the user, and property.
Limited Liability 2.2
Stealth Products, LLC accepts no liability for personal injury or damage to property that
may arise from the failure of the user or other persons to follow the recommendations,
warnings, and instructions in this manual.
Stealth Products does not hold responsibility of final integration of final assembly of
product to end user. Stealth Products is not liable for user death of injury.
Testing 2.3
Initial setup and driving should be done in an open area free of obstacles until the user is
fully capable of driving safely.
The hardware should always be tested without any person sitting in the wheelchair, and
until every alteration of the physical installation or adjustment of the joystick is complete.
DA NGER Identifies an imminent situation which (if not avoided) will
result in severe injury, death,and property damage.
WA RNING Identifies a potential situation which (if not avoided) will
result in severe injury, death,and property damage.
CA UTION Identifies a potential situation which (if not avoided) will
result in minor to moderate injury,and property damage.
NOTICE
Identifies important information not related to injury, but
possible property damage.
SAFETY
Indicates steps or instructions for safe practices, reminders of
safe procedures, or important safety equipment that may be
necessary.

iii
Table of Contents 3.0
1.0 Customer Satisfaction .............................................................................i
1.1 Stealth Commitment .............................................................................................i
2.0 Warnings ..................................................................................................ii
2.1 Warning Labels .......................................................................................................ii
2.2 Limited Liability.......................................................................................................ii
2.3 Testing ......................................................................................................................ii
3.0 Table of Contents……………………………………………………………………………….iii
4.0 Parts and Accessories ............................................................................ 1
4.1 Mounting Hardware Parts ............................................................................... 1
4.2 Tools ........................................................................................................................ 1
5.0 Installation Instructions ........................................................................ 2
5.1 Installing Joystick and Joystick Mount ....................................................... 2
5.2 Mounting Height Adjustment ....................................................................... 3
5.3 Horizontal Alignment ........................................................................................ 4
5.4 Angle Adjustment .............................................................................................. 5
6.0 Maintenance………………………………………………………………………6
6.1 Maintenance…………………………………………………………………………………...6
6.2 Cleaning ................................................................................................................. 6
6.3 Disinfecting ........................................................................................................... 6
7.0 Warranty ................................................................................................. 7
7.1 In Case of Product Failure ............................................................................... 7

1
Parts and Accessories 4.0
A GAT472P-M Mount A1 Clamp Block
B IDM-ALLROUND-9/
IDM-ARLITE-9 A2 Joystick Bracket
C Gatlin1C1 Arm
1 Clamp Screw2C2 Bar Plug
2 Joystick Bracket Screws2
3 Clamp Block Screws2
1. Not included with mount
2. See Tools table
Mounting Hardware Parts 4.1
Tools 4.2
Description Qty
1 M4 x 0.8 x 12mm SHS (B2) Clamp Mount Screw 1
2 M4 x 0.7 x 6mm BHS (A2) Joystick Bracket Screws 4
3 M5 x 0.7 x 6mm BHS (A1) Clamp Block Screws14
4 5mm Hex Key (Allen Wrench)21
5 4mm Hex Key (Allen Wrench)21
1. Included only with IDM-ALLROUND-9/IDM-ARLITE-9
2. Not Included

2
Installation Instructions 5.0
CAUT ION
DO NOT OVER TIGHTEN SCREWS. This could cause wearing of screws
or joystick threads, causing the client to lose efficient control.
Installing Joystick & Mount 5.1
Step 1: Remove Bar Plug (C2). Position joystick (B) into joystick bracket (A2) and tighten joystick
bracket screw (2). Do not over tighten.
Step 2: Align joystick with mount to Gatlin arm (C1).
Step 3: Slide clamp block (A) into arm (C1) to desired horizontal position. Tighten clamp screw, but
do not over tighten. Replace bar plug (C2).

3
Installation Instructions 5.0
Mounting Height Adjustment 5.2

4
Installation Instructions 5.0
NOTICE
Mount clamp (A1) screw (1) should always face away from client.
Horizontal Alignment 5.3
Step 1: Remove bar plug (C2). Loosen clamp screw (1) and slide out mount (A). Loosen joystick
bracket screws (3).
Step 2: Rotate mount clamp (A1) on its own axis, make sure clamp screw (1) faces away from the
user. Align mount clamp (A1) screw slots to joystick bracket (A2) screw slots.
Step 3: Tighten mount clamp screw (3), but do not over tighten.
Step 4: Slide mount back to arm (C1) position and tighten clamp screw (1). Replace plug (C2).
Mounting Height Adjustment 5.2
Step 1: Loosen clamp screw (1).
Step 2: Slide mount (A) into desired horizontal position on arm (C1).
Step 3: Tighten clamp screw again.

5
Installation Instructions 5.0
Angle Alignment 5.4
Step 1: Loosen clamp screw (1). Step 2: Adjust angle mount (A) to desired angle
in a range of 360°. When in position
tighten clamp screw. Do not over
tighten.

6
Maintenance 6.0
Maintenance 6.1
Check every 6 months that screws are tight. Gently tighten any screws
that may have become loose.
Maintain that the hardware is clean and free of dust.
Disinfecting 6.1
Use a damp cloth with any disinfectant detergent and lightly rub
hardware surface.
Rinse thoroughly with clean water.
Cleaning 6.2
Wash away surface dirt and grime with a mild dish detergent and rinse
away.
Moisten a soft cloth with water to rub away any remaining dirt.
Rinse thoroughly with clean water.
SAFETY
For joystick maintenance guidelines refer to the device’s user manual.

7
Warranty 7.0
Our products are designed, manufactured, and produced to the highest of
standards. If any defect in material or workmanship is found, Stealth Products
will repair or replace the product at our discretion. Any implied warranty,
including the implied warranties of merchantability and fitness for a particular
purpose, shall not extend beyond the duration of this warranty. Stealth
Products, LLC does not warrant damage due to, but not limited to:
Misuse, abuse, or misapplicaon of products.
Modicaon of product without wrien approval from Stealth Products, LLC.
Any alteraon or lack of serial number, where applicable, will automacally void this
warranty.
Stealth Products, LLC is liable for replacement parts only.
Stealth Products, LLC is not liable for any incurred labor costs.
No person is authorized to alter, extend, or waive the warranties of Stealth
Products, LLC.
Stealth Products warrants against failure due to defective materials or
workmanship:
Covers: 2 years
Hardware: 5 years
Electronics: 3 years
In Case of Product Failure 7.1
In the event of product failure covered by our warranty, please follow the
procedures outlined below:
1. Call Stealth at [phone] or toll free [phone].
2. Request the Returns Department or obtain an RA from the Returns Department and follow
department or documentaon instrucons.

Stealth Products, LLC. • [e-mail] • www.stealthproducts.com
[phone] | [phone] | 104 John Kelly Drive, Burnet TX 78611
P120D202 Revision Date 2019-12-17