IBEX Nox S User manual

Contents
Foreward 1
Safety Warnings 1
Product Information 2
Product Dimensions 2
Mast-Arm Installation 3
Post-Top Installation 3
Internal Access and Connection 4
Version 1.0
USER MANUAL
Nox S Street Light

Thank you for choosing this quality Ibex product.
We’ve been providing New Zealand businesses with high
performance lighting solutions since 1967.
Please read these instructions carefully. It’s important that you
understand them completely before installation and use.
Foreward
Safety Warnings
Please follow these safety guidelines to ensure your LED tting
functions correctly. Ibex warranty does not cover problems or
damages that occur as a result of mishandling or from non-
compliance with these instructions.
1. Prior to installation, make sure the tting has not been damaged
during transport. If damage has occurred, do not use. Keep the
tting in its original packaging and notify us. We’ll arrange to
repair or replace the tting at our discretion.
2. The tting must be installed and maintained by a qualied
electrician.
3. It is the installers responsibility to ensure the tting is installed
in a location that provides suitable structural integrity.
4. Do not connect the cables with the power on. Check the
connection is correct and that no short circuit will occur before
powering on.
5. The external exible cables xed to the tting cannot be
replaced. If a cord is damaged, do not use.
6. Suitable for outdoor use only.
7. Seismic restraints (where required) are the responsibility of the
installer.
8. The light source of this luminaire is not replaceable; when the
light source reaches its end of life the whole luminaire shall be
replaced.
9. To clean the external surfaces of the tting, wipe with a
soft cloth dipped in diluted washing detergent. Do not use
sandpaper, polishing powder or any other cleaning agent that
may cause damage to the tting.
10. Installers responsibility to ensure the tting is installed in
accordance with New Zealand wiring regulations.
11. Remove all packaging materials from the tting including clear
plastic wrap prior to installation.
1

Product Information
2
Item Power
(max)
Voltage Net Weight
(max)
Sail Area
NSS.XX.XXX.XX.XX.XX.XXX.
XX
85 W 220-240V
50/60Hz
6 KG 0.056m^2
Maximum installation height is 15 m.
Product Dimensions (mm)

2 x M10 Hex socket grub screws
2 x M10 half lock-nuts
Tighten to 10 Nm
2 x M8 Hex socket cap screws
Tighten to 10 Nm
2 x M8 Hex socket cap screws
Tighten to 10 Nm
2 x M10 Hex socket grub
screws
2 x M10 half lock-nuts
Tighten to 10 Nm
1. Loosen 2 x M10 hex grub screws, feed power cable through
spigot and cable gland, adjust alignment and tighten screws.
Adjust throw by loosening 2 x M8 cap screws, adjust in
reference to markings and tighten screws.
3
Mast-Arm Installation
1. Loosen 2 x M10 grub screws, feed power cable through spigot
and cable gland, adjust alignment and tighten screws. Adjust
throw by loosening 2 x M8 cap screws, adjust in reference to
markings and tighten screws.
Post-Top Installation
4

54
1. Remove 2 x M5 cap screws and glass clamps to open lid, feed
power cable through cable gland, connect cable ends to the
correct terminals, tighten cable gland, ensure all internal wiring
is internally contained, close lid and re-tighten cap screws.
Internal Access and Connection
2 x M5 Phillips pan head cap screws
Tighten to 6 Nm
M20 cable gland
Tighten to 4 Nm
3-position terminal block
6 mm
30 mm
10-14 mm
2.5 mm^2
L
N
E

5
Thank you.