iCarsoft Multi-system Scanner i980 User manual

Multi-system Scanner Series User's Manual
EN
I
Disclaimer
All information, illustrations, and specications contained in this
manual are based on the latest information available at the time
of publication. The right is reserved to make change at any time
without notice.
Safety Precautions and Warnings
To prevent personal injury or damage to vehicles and/or the
Multi-system Scanner, please read this user’s manual first
carefully and observe the following safety precautions at a
minimum whenever working on a vehicle:
Always perform automotive testing in a safe environment.• Do not attempt to operate or observe the tool while driving • a vehicle. Operating or observing the tool will cause driver
distraction and could cause a fatal accident.
Wear safety eye protection that meets ANSI standards.• Keep clothing, hair, hands, tools, test equipment, etc. away • from all moving or hot engine parts.
Operate the vehicle in a well-ventilated work area: Exhaust • gases are poisonous.
Put blocks in front of the drive wheels and never leave the • vehicle unattended while running tests.
Use extreme caution when working around the ignition • coil, distributor cap, ignition wires and spark plugs. These
components create hazardous voltages when the engine is
running.
Put the transmission in P (for A/T) or N (for M/T) and make • sure the parking brake is engaged.
Keep a fire extinguisher suitable for gasoline/chemical/ • electrical res nearby.
Don’t connect or disconnect any test equipment while the • ignition is on or the engine is running.
Keep this tool dry, clean, free from oil/water or grease. Use a • mild detergent or a clean cloth to clean it if necessary.

II
Multi-system Scanner Series User's Manual
Table of Contents
1 INTRODUCTION...................................................................1
2 Product Descriptions..........................................................2
2.1 Outline of Multi-system Scanner.....................................2
2.2 Specications..................................................................3
2.3 Accessories.....................................................................3
2.4 Product Troubleshooting.................................................3
2.5 Power supply..................................................................4
3 Tool Setup............................................................................5
3.1 Connection......................................................................5
3.2 Tool Setup.......................................................................6
3.3 Tool Information..............................................................7
4 Diagnose ..............................................................................8
5 Upgrading.............................................................................9
6 FAQ.....................................................................................12

Multi-system Scanner Series User's Manual
EN
1
1 INTRODUCTION
The Multi-system Scanner Series covers the following models:
Multi-system Scanner i980, Multi-system Scanner i960, Multi-
system Scanner i930, Multi-system Scanner i906, Multi-
system Scanner i908 and Multi-system Scanner i902, which is
especially designed for the DIY users and the servicemen of
small service workshop.
Featuring the color LCD display and personalized function
menu, the Multi-system Scanner Series can diagnose full
electronic control system of single vehicle model.
Note: The MULTI-SYSTEM SCANNER may automatically
reset while being disturbed by strong static electricity. THIS IS A
NORMAL REACTION.

2
Multi-system Scanner Series User's Manual
2 Product Descriptions
2.1 Outline of Multi-system Scanner
12
3
4
5
6
7
8
9
10
Figure 2-1
1 Power Indicator Lights up when your tool is
powered on.
2 Cable with OBD II
Connector Connects the Multi-system Scanner to the vehicle’s Data Link
Connector (DLC).
3 LCD Display Indicates test results.
4/7 UP/DOWN Button Move cursor up or down for
selection.
5 OK Button Conrms a selection (or action)
from a menu list.

Multi-system Scanner Series User's Manual
EN
3
6/8 RIGHT/LEFT Button Move cursor right or left for
selection; Or turn page up or
down when more than one page
is displayed.
9 USB Port Connects to computer to update
the Multi-system Scanner.
10 ESC Button Returns to previous menu.
2.2 Specications
1) Screen: 2.8” TFT 262K true color, 320*240dpi
2) Input voltage range: 9~18V
3) Operating current: <100mA@12V (Typical)
4) Power consumption: <1.2W (Typical)
5) Operating temperature: 32°F~122°F / 0°C~50°C
6) Storage temperature: -4°F~158°F / -20°C ~70°C @ RH60%
7) Outline dimension: 4.7’*3.2’*1.0’ / 121*82*26 mm (L x W x H)
8) Weight : < 300g
2.3 Accessories
1) User’s Manual -- Instructions on tool operations
2) USB cable -- Connect to a computer for upgrading online
2.4 Product Troubleshooting
Vehicle Linking Error
A communication error occurs if the scan tool fails to
communicate with the vehicle’s ECU (Engine Control Unit). You
need to do the following to check up:

4
Multi-system Scanner Series User's Manual
A) Verify that the ignition is ON;
B) Check if the scan tool’s OBD II connector is securely
connected to the vehicle’s DLC;
C) Verify that the vehicle is OBD2 compliant;
D) Turn the ignition off and wait for about 10 seconds. Turn
the ignition back to on and continue the testing;
E) Verify the control module is not defective.
Scan tool doesn’t power up
If the scan tool won’t power up or operates incorrectly in any
other way, you need to do the following to check up:
A) Check if the scan tool’s OBD II connector is securely
connected to the vehicle’s DLC;
B) Check if the DLC pins are bent or broken. Clean the DLC
pins if necessary.
C) Check vehicle battery to make sure it is still good with at
least 9.0 volts.
2.5 Power supply
The power of the Multi-system Scanner is provided via the
vehicle’s Data Link Connector (DLC). Follow the steps below to
power it up:
1) Find DLC on vehicle;
Note: A plastic DLC cover may be found for some vehicles
and you need to remove it before plugging the OBDII cable.
2) Plug the connector at the end of OBD II cable to the
vehicle’s DLC.

Multi-system Scanner Series User's Manual
EN
5
3 Tool Setup
3.1 Connection
1) Turn the ignition off.
2) Locate the vehicle’s 16-pin Data Link Connector (DLC).
The DLC (Data Link Connector) is the standardized 16-cavity
connector where diagnostic code readers interface with the
vehicle’s on-board computer. The DLC is usually located 12
inches from the center of the instrument panel (dash), under
or around the driver’s side for most vehicles. If Data Link
Connector is not located under dashboard, a label should be
there telling location. For some Asian and European vehicles,
the DLC is located behind the ashtray and the ashtray must be
removed to access the connector. If the DLC cannot be found,
refer to the vehicle’s service manual for the location.
Figure 3-1
3) Plug the OBDII cable into the vehicle’s DLC.
4) Turn the ignition on. Engine can be off or running.
5) After nishing, press [OK] button to enter Main Menu.

6
Multi-system Scanner Series User's Manual
Figure 3-2
CAUTION: Don’t connect or disconnect any test equipment
with ignition on or engine running.
3.2 Tool Setup
This option enables you to change your interface language and
turn the beeper on/off.
Select [Tool Setup] in the Main Menu and press [OK] to enter.
Figure 3-3
1) Language: To swtich to the desired language.
Choose [Language] and press [OK] to enter. Use [ ] / [ ] key
to select any language and press [OK] to conrm, the system
will switch to the chosen language interface.

Multi-system Scanner Series User's Manual
EN
7
2) Beeper: To turn the Beeper ON/OFF.
Choose [Beeper] and press [OK] to enter. Use [ ] / [ ] to select
ON/OFF and press [OK] to conrm.
3.3 Tool Information
This option allows you to view: boot version, display program
version, diagnostic program version, serial number and register
code.
Figure 3-4
Press [ESC] to return to the previous screen.

8
Multi-system Scanner Series User's Manual
4 Diagnose
This function is specially designed to diagnose electronic control
system of single vehicle model.
Figure 4-1
Refer to the owchart illustrated as below to diagnose a vehicle:
Select “Diagnose”
Automatic
(Note: This mode allows
your tool to scan the vehicle
test system automatically)
Manual Select
(Note: In this case, you need to choose the
desired system manually. Just follow the
on-screen instructions to proceed.)
Select test system
Select test function
Select Vehicle Model
(Note: For different
vechicles, vehicle make
selection may differ.
Generally, we can choose
a vehicle via make year.
But for BENZ, we need to
choose it via chassis.)
Select Vehicle
Manufacturer
Read version
information
Read fault code
Clear fault code
Data stream
Note: For vehicles manufactured by different
vendors, it is possible that it has different
diagnostic menus. For details, please follow
the instructions on the screen to proceed.

Multi-system Scanner Series User's Manual
EN
9
5 Upgrading
Follow the steps described as below to proceed registration and
update:
1. Go to http://www.icarsoft.com or http://www.icarsoft.us and
download the update tool to the computer.
2. Run the iCarsoft_Update_Setup.exe le, and follow the on-
screen instructions to install the update tool (compatible with
Windows XP and Windows 7 operating system).
3. Launch the program when installed, a screen similar to
Figure 5-1 will appear:
Figure 5-1
4. In Figure 5-1, type in the Product Serial Number which is
located at the back of the tool.
5. After the serial number is entered, click Update to jump to
the registration page. Enter the following information and
click OK.

10
Multi-system Scanner Series User's Manual
Figure 5-2
(If you need the Register Code, please refer to steps 6~9.)
(If you have the Register Code, directly proceed to step 10.)
6. The Register Code can be found in your tool. Connect one
end of the supplied USB cord to your tool, and the other end
on the computer.
7. After the tool has powered up and entered the main menu
screen, move the highlight bar on the Tool Information and
press the [OK] button.
8. The Register Code shown in Figure 5-3 is the Register Code
needed in step 5.
Figure 5-3
(Return to step 5 and input the Register Code and then
proceed)

Multi-system Scanner Series User's Manual
EN
11
9. Reopen the update tool, select the updates you would like
to perform, and then click Download to start downloading.
Figure 5-4
10. Once all steps are done, the registration process is
complete.

12
Multi-system Scanner Series User's Manual
6 FAQ
Here we list some frequently asked questions and answers
relating to Multi-system Scanner.
Question: System halts when reading data stream. What is the
reason?
Answer: It may be caused by a slackened connector. Please
turn off the Multi-system Scanner, rmly connect the connector,
and switch on it again.
Question: Screen of main unit ashes at engine ignition start.
Answer: Caused by electromagnetic disturbing, and this is
normal phenomenon.
Question: There is no response when communicating with on-
board computer.
Answer: Please conrm the proper voltage of power supply and
check if the throttle has been closed, the transmission is in the
neutral position, and the water is in proper temperature.
Question: Why are there so many fault codes?
Answer: Usually, it’s caused by poor connection or fault circuit
grounding.
Note: All pictures illustrated here are for reference and
demonstration purpose only and this User’s Manual is subject to
change without prior notice.

Multi-system Scanner Serie Benutzerhandbuch
DE
I
Disclaimer
Alle Informationen, Beschreibungen und Angaben in diesem
Handbuch, basieren auf die letzten verfügbaren Informationen zu
dem Zeitpunkt der Veröffentlichung. Wir behalten uns das Recht vor,
Veränderung jederzeit ohne weitere Ankündigung vorzunehmen.
Sicherheitshinweis und Warnungen
Um Verletzungen an Personen oder Schäden an Fahrzeugen
und/oder dem Diagnosegerät zu verhindern, lesen Sie zuerst
diese Bedienungsanleitung und beachten Sie die folgenden
Sicherheitshinweise wenn Sie an einem Fahrzeug arbeiten.
Arbeiten immer in einer sicheren Umgebung ausführen.• Bedienen Sie niemals während der Fahrt dieses Diagnosegerät, • der Fahrer kann wird dadurch abgelenkt und ist eine Gefahr für
die Straßenverkehrsordnung.
Tragen Sie angemessene Schutzkleidung des ANSI Standards.• Halten Sie Kleidung, Haare, Hände, Werkzeuge, Prüfmittel • usw.… von allen sich bewegenden oder heißen Motorteilen weg.
Starten Sie das Fahrzeug in gut belüfteten Bereichen, • Auspuffgase sind giftig.
Sichern Sie das Fahrzeug vom wegrollen und lassen Sie das • Fahrzeug bei Arbeiten nie unbeaufsichtigt.
Seien Sie besonders vorsichtig bei Arbeiten rund um die • Zündspüle, Zündverteiler, Zündkabel und Zündkerzen.
Diese Komponenten erzeugen lebensgefährliche Spannung • sobald der Motor läuft.
Legen Sie den Neutral Gang (bei Schaltgetriebe) und bei • Automatikgetriebe stellen Sie den Hebel auf „P“ für Parken.
Ziehen Sie die Handbremse.
Halten Sie einen Feuerlöscher für Elektrische Brände in • Reichweite.
Trennen Sie das Diagnosegerät niemals währen die Zündung • eingeschalten ist oder der Motor läuft.
Lagern Sie diese Diagnosegerät trocken, sauberen und frei • von Öl und Wasser oder Fett. Verwenden Sie ein mildes
Reinigungsmittel und eine sauberes Tuch um das Äußere des
Diagnosegerätes zu reinigen, wenn nötig.

II
Multi-system Scanner Serie Benutzerhandbuch
Table of Contents
1 Einführung ...........................................................................1
2 Produktbeschreibung .........................................................2
2.1 Funktionsübersicht..........................................................2
2.2 Technische Angaben.......................................................3
2.3 Zubehör ..........................................................................3
2.4 Fehlerbehebung..............................................................3
2.5 Stromversorgung............................................................4
3 Geräteeinstellungen............................................................5
3.1 Verbindungen..................................................................5
3.2 Einstellungen..................................................................6
3.3 Tool Informationen..........................................................7
4 Diagnose ..............................................................................8
5 Update / Upgrade.................................................................9
6 FAQ.....................................................................................12

Multi-system Scanner Serie Benutzerhandbuch
DE
1
1 Einführung
Die Multi-system Scanner Serie beinhaltet folgende Modelle:
Multi-system Scanner i980, Multi-system Scanner i960, Multi-
system Scanner i930, Multi-system Scanner i906, Multi-system
Scanner i908 and Multi-system Scanner i902, welche besonders
geeignet für DIY Benutzter sind sowie kleinere Werkstätte.
Ausgestattet mit einem Farb-LCD-Display kann der Multi-
System Scanner einzelne Steuergeräte von verschiedenen
Fahrzeugmodellen auslesen.
Hinweis: Der MULTI-System Scanner kann aufgrund der
starken Statischer Elektrizität gestört werden. Das ist aber
vollkommen normal.

2
Multi-system Scanner Serie Benutzerhandbuch
2 Produktbeschreibung
2.1 Funktionsübersicht
12
3
4
5
6
7
8
9
10
Abbildung 2-1
1 Power Knopf Leuchtet sobald das Gerät
angeschlossen ist
2 Kabel mit OBD II
Verbindung Kabel für die Verbindung am Fahrzeug
3 LCD Display
4/7 HOCH/RUNTER Knopf Cursor von oben nach unten
bewegen
5 OK Button Von der Menu-Ansicht.

Multi-system Scanner Serie Benutzerhandbuch
DE
3
6/8 RECHTS/LINNKS
Knopf Bewegt der Cursor links oder rechts; Oder eine Seite weiter,
wenn mehre Seiten verfügbar
sind
9 USB Port Verbindung für den Scanner an
den Computer
10 ESC Knopf Zurück oder zum letzten Menü
2.2 Technische Angaben
1) Display: 2.8” TFT 262K true color, 320*240dpi
2) Eingangsspannung: 9~18V
3) Betriebsspannung: <100mA@12V (Typical)
4) Stromverbrauch: <1.2W (Typical)
5) Betriebstemperatur: 32°F~122°F / 0°C~50°C
6) Lagertemperatur: -4°F~158°F / -20°C ~70°C @ RH60%
7) Abmessung: 4.7’*3.2’*1.0’ / 121*82*26 mm (L x W x H)
8) Gewicht : < 300g
2.3 Zubehör
1) Benutzerhandbuch – Anleitung und Hilfestellung zum
Diagnosegerät
2) USB Kabel – Verbindet den Computer mit dem Scanner
2.4 Fehlerbehebung
Fahrzeug Verbindungsfehler
Ein Kommunikationsfehler tritt auf, wenn der Scanner nicht mit
der Fahrzeug-ECU (Motorsteuergerät) kommunizieren kann.