ID View IV-BV7660IR-AHDM User manual

Quick Start Guide
Item Number: IV-BV7660IR-AHDM
Thank you for purchasing our products. Please read the cut-sheet carefully before operating.
Safety Precaution
Warning
* To prevent fire or shock hazard, please do not immerse the unit into the water
for a long period of time.
* Please make sure the adapter used is consistent with product specifications,
Otherwise, it might cause fire, electric shock or damage.
* Pay attention to polarity of the adapter, it might cause some accidents like fires,
and will burn out the camera.
* Please don’t connect multiple cameras with the same adapter at the same time;
overloading of adapter capacity may cause fires.
* Power supply must be firmly fixed so as not to cause fires.
* If the device gets abnormal smell or smoke, please stop it immediately and
contact our customer service center.
* If the camera doesn’t work, please do not dismantle it by yourself.
Please contact our local distributor or our maintenance office to trouble shoot,
Otherwise, the warranty is voided.
* Please do not splash water on the product components when cleaning.
Technical Specifications
Item Number:
IV-BV77660IR-AHDM
Signal System:
NTSC
Sensor CCD:
1/3” Progressive Sensor
Resolution:
720P
Lens:
Vari-focal 6-60mm
OSD:
YES

Installation
1. Connect the terminated power wire of the cable directly to theAC or DC power source.
2. Connect the BNC output of the Camera to an extension cable, or directly to
a DVR / Observation System or to a TV/Monitor.
3. Fix up the pedestal on the ceiling, fix up the screw of pedestal.
4. Aim and adjust the “Field of View” as desired, then fix up the screw of horizontal angle.
5. Next, choose a satisfactory angle at which to aim the camera then connect the
screw of declining angle.
Push the Joystick up / down to select among menu items.
Push the Joystick left / right to adjust the level of the selected item.
Press the Joystick to enter the submenu or exit the OSD Setup Menu.
Note: The function button is not only for direction control, also for switching video format and
video output. Please follow the detailed instruction as below:
Push the joystick "DOWN" button key over 5 seconds to switch video format from PAL to
NTSC.
Push the joystick "LEFT" button key over 5 seconds to switch video output from 720p to 960H
(CVBS is the default).
Push the joystick "RIGHT" button key over 5s to switch video output from 960H to 720p.
6. Tear apart the outer packing (figure 1) to take out the Desiccant Bag (figure 2), then put it into the camera
housing (figure 3)
Minimum Illumination:
0 LUX (IR ON)
S/N Ratio:
More than 52 dB
Distance:
150ft
LED:
12 PCS High Density IR LED
Video Output:
1Vp-p 75Ω . AHDM / CVBS switch
Connector video:
BNC
Operation Temperature:
-4°F to +122°F
Supplied Power:
24VAC, 12VDC(+/-10%);

Figure 1
Figure 2
Figure 3
Note: It’s recommended to close the cover cap immediately in case of reducing the absorption capacity
of the desiccant bag inside the camera.
Troubleshooting
1. No picture or unstable - Check the connection for video cable and/or power cable.
2. The image is so blurred
1) Check if there is some dirt on the lens, then use customized lens paper or
cotton with alcohol to clean.
3. The image is so dim - Adjust the CNT of monitor and iris
4. Screen color cast in the special environment - Adjust direction
5. The screen glittering - The camera might face to the sun, TV set or computer.
6. The camera works abnormal; the surface over-heat; has peculiar smell, smoke etc.
- Please cut off the power supply immediately. Secondly, check the connection to
the power supply. If the camera is deemed faulty, send it back to your vendor or authorized reseller for repair.
Accessory List

* If the camera doesn’t work, please do not dismantle it by yourself.
Please contact our local distributor or our maintenance office to trouble shoot,
Otherwise, the warranty is voided.
* Please do not splash water on the product components when cleaning.
Configuration in the OSD Menu
You can use the Joystick on the rear panel of the camera to configure camera settings in the OSD menu. For details on the
OSD menu structure as below:
No.
Main
Sub Menu
Sub Menu / Function
1
Lens
DC*
Mode
Indoor
Outdoor*
Min Shu.
NTSC: 1/30*
PAL: 1/25*
Max. Shu.
NTSC:
1/60,FLK,1/240,
1/480,1/1000,
1/2000,1/5000*,
1/10000, 1/50000
PAL:
1/50,FLK,1/200,
1/400,1/1000,
1/2000,1/5000*,
1/10000, 1/50000
Iris Speed
0 –15(0*)
Manual
2
Exposure
Shutter
NTSC: 1/30, 1/60, FLK, 1/240, 1/480, 1/1000, 1/2000, 1/5000,
1/10000, 1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30, Auto*
PAL: 1/25, 1/50, FLK, 1/200, 1/400, 1/1000, 1/2000, 1/5000,
1/10000, 1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30, Auto*
AGC
0 –15(15*)
Sens-up
Off*
Auto
Sens-up
X2, X4*, X6, X8, X10, X15, X20, X25,
X30
Brightness
1-100(40*)
D-WDR
Off*
On
Level
0-8(8*)
No.
Name
Quantity
Remark
1
CCTV Camera
1
2
User Manual
1
3
Screw
1

Auto
Defog
Off*
Auto
Pos/Size
Position, Size,↑,↓,→,←
Gradation
0-2(0*)
Default
3
Backlight
Off*
BLC
Level
Middle*, High, Low
Area
Position, Size,↑,↓,→,←
Default
HSBLC
Select
Area1*, Area2, Area3, Area4
Display
Off
On*
Position, Size,↑,↓,→,←
Black Mask
On*/Off
Level
0-100(20*)
Model
All Day*
Night
AGC Level
0-255(48*)
Default
4
White
Balance
ATW*
AWC→SET
Indoor
Outdoor
Manual
Blue
1-500(50*)
Red
0-100(50*)
AWB
5
Day &
Night
Ext*
D→N(Delay)
0-60(1*)
N→D(Delay)
0-60(1*)
Auto
D→N(AGC)
1-255(240*)
D→N(Delay)
0-60(1*)
N→D(AGC)
1-255(50*)
N→D(Delay)
0-60(5*)
Color
B/W
Burst
Off*/On

IR Smart
Off
On*
Level
0-15(4*)
Area
Position, Size,↑,↓,→,
←
IR PWM
Off
0-100(100*)
6
NR
2DNR
Middle*/Low/Off/High
3DNR
Middle*/Low/Off/High
7
Special
Cam Title
Off*
On
0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ▶
→←↑↓()ˉ-_▊/=&:~,.
D-effect
Freeze
Off*/On
Mirror
Off*, Mirror, V-flip, Rotate
Neg. Image
Off*/On
Motion
Off*
On
Select
Area1*,Area2,Area3,Area4
Display
On*
Position, Size,↑,
↓,→,←
Off
Sensitivit y
0-100(64*)
Color
Green*, Blue, White, Red
Trans
1.00*,0.75,0.50,
0.25
Alarm
View Type
Off, Block, Outline,
All*
OSD View
On*/Off
Alarm Out
On*/Off
Alarm Sig
High*, Low
Time
1-15(3*)
Default
Privacy
Off
On
Select
Area1*,Area2,Area3,Area4
Display
Off

Color*
Position, Size,↑,
↓,→,←
Mosaic
Position, Size,↑,
↓,→,←
Inv
Position, Size,↑,
↓,→,←
Color
White*, Black, Red, Blue, CYAN,
Yellow, Green
Trans
1.00*,0.75,0.50,
0.25
Default
Language
ENG*/CHN1/CHN2/GER/FRA/ITA/SPA/POL/RUS/POR/NED/TUR
Defect
Live DPC
Off
On*
AGC level
0-255(65*)
Level
0-100(100*)
White DPC
Off
On*
Pos/Size
Position, Size,↑,
↓,→,←
Start
Close the iris then
press
DPC View
Off*/On
Level
0-60(5*)
AGC
0-14(14*)
Sens-up
x2*, x4, x6, x8,x10,
x15, x20, x25, x30
Black DPC
Off*
On
Pos/Siz
Position, Size,↑,
↓,→,←
Start
Press Enter
DPC View
Off*/On
Level
0-255(255*)
RS485
CAM ID
0-255(1*)
ID Display
Off*/On
Baud Rate
2400,4800,9600,19200 ,38400
8
Adjust
Sharpness
Off

Auto*
Level
0-10(6*)
Start AGC
0-255(50*)
End AGC
0-255(200*)
CRT/LCD
CRT
Black Level
0-60(0*)
Blue Gain
0-100(50*)
Red Gain
0-255(50*)
LCD*
Gamma
User*,0.45,0.50,0.55,0.60,0.65,0.
70,0.75,0.80,0.85,0.90,
0.95,1.00
Blue Gain
0-100(50*)
Red Gain
0-100(50*)
LSC
Off*/On
Video. Out
PAL/NTSC
9
Exit
Save& END /Reset/Not Saved