Ideal Warehouse AutoStand User manual

1-866-828-6737 idealwarehouse.com 2021-03-08
Original Instructions
AutoStand Wide Trailer Stand
Operation Manual
Important notes
•Only trained and authorized individuals should use this product.
•Use only original Ideal Warehouse Innovations, Inc. parts to service this product.
•Do not maneuver on steep surfaces; use only on stable, flat surfaces.
Before you begin
•Complete a visual inspection of the AutoStand Wide for any obvious maintenance issues.
•Be careful moving around the loading dock area to ensure it is safe to move around the area.
•Use appropriate personal protective equipment such as gloves, safety glasses, safety vest,
hearing protection and protective shoes.
Set up
•The AutoStand Wide’s versatility lies in its ability to accommodate a vast range of trailer sizes.
This is due to two features:
1. Step feature (top).
2. Adjustable height via clevis pin (bottom).
•With the AutoStand Wide in locked position, the lowest height possible, on the lowest step is 42”;
and the maximum height possible on the highest step is 52 ½”.
•Adjust the height of the AutoStand Wide using the clevis pin as needed, with the intent of
keeping it in this position, using the steps as the variable height options for your daily trailer
variations.
Product intended to
prevent trailer up-
ending and tip-over by
shouldering the weight
in heavy-duty loading
dock environments.

1-866-828-6737 idealwarehouse.com 2021-03-08
Operation
Step 1:
Using the handles, position the AutoStand Wide
under the nose of trailer, ensuring the stand is
positioned approximately in the center of the
trailer.
Step 2:
Push the AutoStand Wide under the nose of the
trailer until one of the “steps” catches the
trailer. This determines which “step” on the unit
will support the load. Pull unit back slightly to
allow clearance.
Step 3:
Press the release latch with your foot to lower
the frame off the wheels and onto the ground.
The AutoStand Wide is now locked in place.
Critical safety tip:
When pressing the release latch, the unit will drop onto the ground instantly. MAKE SURE
there is nothing under the frame base plates beforehand as the unit possess considerable
weight.

1-866-828-6737 idealwarehouse.com 2021-03-08
Removing the AutoStand Wide Trailer Stand
Step 4:
Press firmly on the foot pedal with your foot to
raise the unit off the ground and onto its
wheels. Keep pressing until the latch is
engaged, locking the unit in its mobile position.
Use the brakes on the back wheels when storing
unit in its mobile position.
Once removed, store the unit out of the way of dock traffic and complete a visual inspection to ensure
there are no obvious maintenance issues.
Warranty Statement
Ideal Warehouse Innovations, Inc. warrants for a period of three hundred and sixty-five (365) days from date of installation, or
three hundred and seventy-five (375) days from date of shipment, whichever shall occur first, that all products and service parts
shall be free from defects in workmanship and material. If the equipment or any part thereof, is returned, transportation
charges pre-paid, within the periods specified above, and if examination by Ideal Warehouse Innovations, Inc. discloses to its
satisfaction that the said equipment or part thereof has been defective in workmanship or material, it will deliver to the
purchaser, without charge, parts of the first class workmanship and material in exchange for any parts so found to be defective,
and Ideal Warehouse Innovations, Inc. is limited to said exchange.
This warranty shall not apply: (1) to maintenance service or adjustment; and (2) to any equipment which shall have been
repaired or altered outside of Ideal Warehouse Innovations, Inc. or its authorized service representatives.
These warranties are in lieu of all other warranties, expressed or implied, including, without limitation, warranties of
merchantability and fitness for purpose, all other representations to the first user purchaser, and all other obligations or
liabilities, including liability or incidental and consequential damages, on the part of Ideal Warehouse Innovations, Inc. No
person is authorized to give any other warranties or to assume any other liability on behalf of Ideal Warehouse Innovations, Inc.
unless made or assumed in writing by Ideal Warehouse Innovations, Inc.

1-866-828-6737 idealwarehouse.com 2021-03-08
AutoStand Wide Trailer Stand Parts Listing
KEY
PART NUMBER
DESCRIPTION
QTY.
1
Not Available
BASE FRAME WELDMENT
1
2
60-5445-100
COVER PLATE
1
3
60-5445-101
RELEASE LATCH
1
4
60-6445-102
SLIDE FRAME
1
5
60-5445-103
FOOT PEDAL
1
6
60-5445-104
STEPPED CAP
2
7
Not Available
BASE FRAME
1
8
60-5445-1
8" SWIVEL CASTOR
4
9
60-5445-200
GAS SPRING, 150lbs
1
10
60-5445-203
LINCH PIN, 3/16"OD x 1"
8
11
60-5445-204
COTTER PIN, 1/8"DIA x 1.25"LG
2
12
60-5445-201
EXTENSION SPRING, 1/2"OD x 1.75"LG
1
13
60-5445-205
ROUND GRIP FOR 1"OD, 5-1/16"LG
2
14
60-5445-202
SKATE WHEEL; STEEL, 2.25"OD x 13/16" WIDE
8
60-5445-206
Full Set of Hardware for Auto Stand Wide (Includes all below parts & quantities)
1
KEY
DESCRIPTION
QTY
KEY
DESCRIPTION
QTY
15
UHMW WASHER, 1.312"OD x 0.736"ID x 0.065"
2
24
HEX BOLT, 5/16 UNC x 7/8; FULL-THD, Gr5, ZP
20
16
CLEVIS PIN; 3/4"OD x 3-3/4"
1
25
LOCKNUT, 1/4 UNC; Gr5, ZP
2
17
CLEVIS PIN, 3/4"OD x 4.75"LG, ZP
1
26
LOCKNUT, 5/16 UNC; Gr5, ZP
26
18
CLEVIS PIN, 1"OD x 4 3/16"LG, ZP
8
27
LOCKNUT, 1/2 UNC; Gr5, ZP
2
19
HEX BOLT, 1/4 UNC x 1 1/2; Gr5, ZP
1
28
WASHER, FLAT, 1/4"; ZP
2
20
HEX BOLT, 1/4 UNC x 2 1/4; Gr5, ZP
1
29
WASHER, FLAT, 5/16"; ZP
28
21
HEX BOLT, 5/16 UNC x 3; Gr5, ZP
4
30
WASHER, FLAT, 1/2"; ZP
3
22
HEX BOLT, 1/2 UNC x 2 3/4; Gr5, ZP
1
31
WASHER, FLAT, 3/4"; ZP
4
23
HEX BOLT, 1/2 UNC x 5; Gr5, ZP
1

1-866-828-6737 idealwarehouse.com 2021-03-08
Recommended Safety Inspection and Maintenance Schedule
Inspect for
Action
Before each use:
A visual check should be
performed before each use.
Check for any bent parts and broken welds. Make sure the release
latch is functioning and the clevis pins (item no. 10) used for height
adjustments are secure.
Monthly:
Up and down function. Should
lower automatically when release
latch is pressed and raise by
pushing on the foot pedal.
1. Raise and lower unit.
2. If smooth functioning is compromised, check the release latch and
any corresponding springs and fasteners.
3. Clean parts if needed.
4. Tighten fasteners if needed.
5. Replace springs, fasteners or other parts if necessary.
Yearly:
Inspect for bent, damaged or
missing handlebars, fasteners,
grips, castors, springs, labels, etc.
1. Check to ensure all moving parts operate smoothly.
2. Clean labels so instructions are clear and visible.
3. Replace or repair if necessary.