Iiglo TVL1102 User manual

CAUTION: DO NOT EXCEED
RATED LISTED WEIGHT. SERIOUS
INJURY OR PROPERTY DAMAGE
MAY OCCUR!
60"
MAX
200x200
300x300
400x200
400x400
19
40kg
(88lbs)
RATED
Installation Manual
Motorized
TV Wall Mount
TVL1102

21
NOTE: Read the entire instruction manual before you start installation and assembly. Component Checklist
WARNING
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation.
If any parts are missing or faulty, telephone your local distributor for a replacement.
Package M
adapter bracket (x2)
D
Package W
ST6.3x55 (x5)
W-A
concrete anchor
W-B
(x5) D6 washer (x3)
W-C
motorized wall mount (x1)
A
washer
M-F
(x4) big
M-H
spacer (x8)small spacer (x8)
M-G
cable clip (x2)
C
wall template (x1)
B
remote control (x1)
F
power supply (x1)
G
• Do not begin the installation until you have read and understood all the instructions
and warnings contained in this installation sheet. If you have any questions
regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This pr oduct should only be installed by someone with good mechanical ability
who has basic building experience and fully understands this manual.
• Make sure that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. The use of a stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position
the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage
to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
• Please do not disassemble or change the electronic components of the product
without authorization.
IR receiver (x1)
E
bubble level (x1)
H
M6x30
M-C
(x4)
M5x14
M-A
(x4) M6x14
M-B
(x4) M8x30
M-D
(x4)
M8x50
M-E
(x4)

The swing arm needs to be adjusted
according to the size of TV.
X= L/2+260(mm)
L:The length of TV
Remove the screws and washers using
the proper phillips screwdriver.
WARNING
• Make sure that mounting screws are anchored into the center of the studs. The use of a stud
finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined weight of the
equipment and all attached hardware and components.
4a. For Wood Stud Wall Mounting
Drill pilot holes
3
X X
√
ø 4.5mm
(ø 3/16")
55mm
(2.2")
55mm
(2.2")
2
1
Find and mark the exact
location of mounting holes
3
W-A
X
7mm
4
X
X
X=TV(L)/2+260mm
W-A
7mm
2.Opening Hard t he Sw ing Arm
1. Sepa ra t ing t he Decora t ive Cover s from t he W all M ount
3. Posit ion t he Sw ing Ar m
90°
Reinstalling the screws and washers
the swing arm after finishing the adjustment.
to secure
Reverse installation
Forward installation
Tighten the screw leaving a 7mm space
from the wall.
H
H

56
X X
√
Installers must verify that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
WARNING
4b. For Solid Brick and Concrete Mounting
Drill pilot holes
2
60mm
(2.4")
60mm
(2.4")
ø 10mm
(ø 3/8")
1
Mark the exact
location of
mounting holes
W-A
W-B
7mm
W-A
W-B
W-C W-A
X X
√
Screw the wall
mount onto
the wall
Reverse installation
Forward installation
Tighten the screw leaving a 7mm space
from the wall.
H
H
H
7mm

87
5. I nstalling the Decorat ive Covers and the Cable Clips
X X
√
Screw the wall
mount onto
the wall
H
W-C W-A
C

109
or
6-2 For Recessed Back Screens or to Access A/V Inputs
TV
TV
TV
Tighten all screws but do not over tighten.
· Screw the adapter brackets onto the TV.
· Position the adapter brackets as close as possible to the middle of the screen.
Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.
6-1 For Flat Back Screens
TV
TV
TV
6. Installing the Adapter Brackets
Remove the screws on the adapter brackets
and keep the screws for later use.
M-C
M-D
M-F
M-G
or
oror
M-F
M-A
M-F
M-B
M-C
M-D
M-F
M-H
M-C
M-D
M-F
M-G
M-H
M-E
M-F
M-H
M-G
M-E
M-F
M-H
M-G
M-E
M-F
M-H

12
11
8. Cable Management
Connect the cables to your TV and route through the cable clips.
Note: Leave slack in the cables for arm movement.
or
90°
90°
or
7. Hooking the TV onto the Wall Mount
Hook the TV over the swing arm.
Important:Make sure the TV is correctly hooked before releasing the TV.
Reinstall the bottom screws to secure the adapter brackets to the swing arm.
To avoid the little tilt caused by weight, you can tighten the
adjustment screws to help level the TV.
H

Buttons function instructions
LEARN MODE operation instructions
The loss of matched remote control would result in TV wall mount being unusable. The LEARN MODE is
used to learn how to use TV remote (ONLY suitable for the TV remote of popular brands.) to control TV
wall mount.
Note:
• TV remote can’t replace the all functions of matched remote control. Only LEARNING the three buttons
functions. With , and respectively.
• The user must follow the rules below when using the TV remote to control TV wall mount.
Select the alternate buttons from the TV remote, and the button that can't direct control the TV.
• If you need to erase all the button functions LEARNED, press and hold for 3 seconds and repeat
five times.
If you don't erase them, the new button functions LEARNED every time will overwrite the last button
functions LEARNED.
OK
1413
10. The Remote Control Operating Instructions
Remote control operation instructions
STEP 1: When powered, the buzzer sounds once beep, TV wall
mount will be in standby state.
STEP 2: Forward and reverse installation choices (NOTE 1:
There are forward and reverse installations for the TV wall
mount. Swinging the TV wall mount to right against the wall
that defaults to the forward installation. If it is the forward
installation, the STEP 2 is not required; If it is the reverse
installation, Press and hold for 5 seconds until the buzzer
sounds twice beep beep, Remote control is now successfully
set.
RMT-01
remote control
9. Placing the IR Receiver
Peel the backing paper. Place the IR receiver into desired position.
Make sure nothing will obstruct the transmission from where the TV will be viewed.
Do not plug into the power outlet until it is ready to be operated.
Do not open the electrical cover please.
Stop button
OK
Memory button1.Press and hold for 3 seconds, the buzzer will sound twice beep beep, The
memory is saved as location 1.
Memory button2.Press and hold for 3 seconds, the buzzer will sound twice beep beep, The
memory is saved as location 2.
Forward and reverse installation choices button (Pressing the button is invalid once in the working
condition).
+Learning button, Please read the instructions below for more info.
+To recall the button(location 1). Press and release button, and then press button,
The TV wall mount will automatically swivel to the location1 after the buzzer sounds once.
+To recall the button(location 2). Press and release button, and then press button,
The TV wall mount will automatically swivel to the location2 after the buzzer sounds once.
The left button. Press and release , the TV wall mount will swivel to the left until is pressed
or the TV wall mount swing to 90 degrees to stop.
OK
The right button. Press and release , the TV wall mount will swivel to the right until is pressed
or the TV wall mount swing to 0 degrees to stop.
OK
Follow the Key function instructions below to operate.
STEP 3: Press and release OK to return the TV wall mount flat
against the wall and hear one beep from the buzzer, the system
will then enter a working condition.
G
E
Reset mode
STEP 1: Restart the power.
STEP 2: Press and hold for 3 seconds and repeat three times. The system will start automatic
positioning: First TV wall mount with flat against the wall, then TV wall mount with
90°of lateral rotation until the TV wall mount automatically stop at 90°position.
positioning positioning
Note : the remote control should use AAA battery.

15
11. Repair
In F ront
This repair guide intents to help you identify and solve the minor problems caused by unusual operation of the
electric system of our electric TV mounts. The simple procedures in this manual are easy to follow and capable of
solving the most problems happened in everyday use.
Er ror Indica tion
1. T he Buzz er Constantl y Giv es Out Alar m Sound:
The Error Of Positioning Signal
Reset the system by following the instruction manual. If the alarm sound continues, please contact us to replace the
product.
21
pr oduct
OK
OK
LEARN MODE instructions as shown below:
STEP1: Press and hold for 3 seconds until LED light on the matched remote control stays on, and
then press . The buzzer will sound once, the red LED light on the IR receiver will stay on, then the
LEARN MODE will be entered.
STEP2: If LEARN , please press on the matched remote control until the buzzer sounds twice,
the red LED light on the IR receiver will change from being steady to a slow flash.
STEP3: Aim the TV remote at the IR r eceiver, and press the button on the TV remote that you need to set as
the function of button until the buzzer sounds three times. the red LED light on the IR receiver will
change from slow flash to a fast flash.
STEP4: Press button on the matched remote control until the buzzer sounds four times. The
red LED light on the IR receiver will turn off. button will be LEARNED successfully. If the buzzer only
sounds once, then a LEARN failure.(The TV remote won’t support the LEARNING function).
(Please follow step1 through step4 in turn if the user need to LEARN more buttons)
Learn “Power” button on the TV remote:
Press and hold for 3 seconds until LED light on the matched remote control stays on , and then press .
The buzzer will sound once, the red LED light on the IR receiver will stay on, then press and hold button
on the matched remote control until the buzzer sounds twice, then release the button. The red LED
light on the IR receiver will change from being steady to a slow flash.
Aim the TV remote at the IR receiver, and press “Power” button. The buzzer will sound three times. The red
LED light on the IR receiver will change from slow flash to a fast flash. Press button on the matched
remote control until the buzzer sounds four times. The red LED light on the IR receiver will turn off. “Power”
button will be LEARNED successfully. If press “power” button, the TV wall mount will automatically reset.
Note: When there is no activity for over 20 seconds in any step .TV remote will automatically exit from the
LEARN MODE.
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your distributor if you have any questions.
OK
OK
Remote Contr ol Pr oblems
1. Abnor mal Loss Of Pow er
(Batteries Are Out Of Power After 24hrs Without Using The Remote Control.)
Please contact us to replace remote control.
2. Buttons On R emote Contr ol Don ’t W or k.
1. Please check if the infrared ray receiver is properly connected to the product.
2. Please check if the batteries have power. If the problem isn’t solved, please contact us to replace the remote control
and infrared ray receiver. If the problem is still not solved after the replacement, please contact us to replace the product.
21
24hr s
1 2 3
pr oduct
or
3. T he Insensitivity Of Remote Contr ol (The Functional Distance Is Less Than 3m.)
Please replace the batteries. If the problem is still not solved, please contact us to replace remote control and infrared
ray receiver.
21
Unstead y Mo vement
Please check if the TV mount is evenly installed. If not, please readjust the TV mount to an even position. If the problem
still happens please contact us to replace the product.
16

Can ’t Oper ate
Please check if the power adaptor is properly connected to the product. If so, please turn the power on. If there is no
buzzer sound or red light power indication, please check if the power adaptor works properly. If the power adaptor
doesn’t work please contact us to replace the power adaptor. If the power adaptor works properly, but the TV mount
doesn’t work, please contact us to replace the product.
1 2 3
pr oduct
or
21
pr oduct
Please contact us to replace the product.
21
pr oduct
Motor Can ’t Stop/Anti-Collision Mec hanism Slips
Please contact us to replace the product.
pr oduct
1
Abnor mal Noise
17 18