iLight EG2-S User manual

Mounting & Installation Technical Data
Typical Schematic
Electrical & Mechanical
Control: Via iLight network connection
Supply: +10 - 24V DC @ 750 mA Max (via external power supply)
Terminal Size: iCANnet cable size: 5 x 1mm2. Power cable size: 2 x 1mm2
Protection: Provided by installer
Recommended Cable: iCANnet Network Cable
Ambient temperature: 2°C – 50°C
Relative humidity: 5% - 95% max, non-condensing
IP rating: IP20
Installation: Installation must be carried out by a suitably qualied electrician
and installed in a suitable DINrail enclosure.
Dimensions: 106mm (w) x 91mm (h) x 62mm (d)
Weight: 0.22kg
Software
For programming EG2-S, Device Editor software is required.
Please consult your iLight representative for latest versions.
EG2-S
Ethernet Gateway
Doc No: 9850-000916--00
EG2-S must be mounted in a suitable enclosure to provide regulatory
protection from electric shock hazard as well as protecting the iCANnet
data network from tampering that could lead to reduced network security.
Ensure selected enclosure provides adequate cooling ventilation.
Fixing to DIN rail
1. Fix top clips over DIN rail.
2. Pull down bottom clip using screwdriver.
3. Close module towards DIN rail.
4. Push up bottom clip to x securely to DIN rail.
Removing from DIN rail
1. Pull down bottom clip with screwdriver.
2. Lift module away from DIN rail.
1
2
3
4
1
2
EG2-S
Ethernet Gateway
Local PC
Remote PC
WIFI Router
Laptop /
Wireless Devices
WWW
Network Sensor
iCAN Network
Lighting Source
Controller
E&OE. iLight reserve the right to make
changes to the equipment without
prior notice.
© Signify Holding
iLight
Usk House, Lakeside
Llantarnam Park,
Cwmbran,
NP44 3HD, UK
t: [phone]
e: [email protected]
www. iLight.co.uk
EU Authorised Representative
Cooper Lighting Netherlands B.V.
High Tech Campus
HTC 48
Eindhoven
5656 AE
Installation Guide

iLight Network
Termination
Connection
to the iLight
Network
Connection to
non-PoE port on
ethernet switch
Power Supply
+10 - 24V DC @ 750 mA Max
Device
Identication
Switch
Data LED
Status LED
Power Supply Jumper
Enables iLight Network BUS power when in the ‘ON’ position. Disables
iLight Network BUS power when removed or in the ‘OFF’ position.
Caution: This product requires 10-24V@750mA. When using the network
to power this device ensure adequate power is available on the network.
9850-000916--00 . E&OE.
Typical Connection Diagram
EG2-S
Ethernet Gateway
Status LED
Green LED ashes – device OK
Data LED
Red LED ashes when messages sent on network.
Device Identication
Press and release switch.
Sending a message to identify the device on the
network (red Data LED ashes)
Device LEDs and Buttons
iCAN network wiring
Cable connections to the iCAN network are made to
a removable 5-way connector block located on the
EG2-S
Function iCANnet Cable Colour
0V Black
CAN L Blue
Shield Silver
CAN H White
+V Red
+V CAN H SHIELD CAN L 0V
Maximum segment distance: 500m (1640 ft)
Devices per segment: 100 (without bridge or repeater)
Consult iLight for information on alternative cable
types.
IMPORTANT NOTE: Connecting a mains potential
cable to the iCAN Network terminals is likley to
damage the unit and other devices connected, and
invalidate warranty.
Network termination
EG2-S is supplied with termination
disabled as standard. If it is connected
as an end device on the iCAN network,
the jumper will need to be moved to
enable termination.
To enable termination, move the jumper
downwards from the top two pins to
the bottom two pins. Termination
OFF
Termination
ON