iLive IT188B User manual
USER’S GUIDE
V:1401-0813-10
For the most up-to-date version of this User’s Guide, go to www.ilive.net
IT188B
Bar Speaker for iPod
2
• WARNING:Lithium batteries, like all rechargeable
batteries are recyclable and should be recycled or
disposed of in normal household waste. Contact your
local government for disposal or recycling practices in
your area. They should never be incinerated since they
might explode.
• WARNING: Shock hazard - Do Not Open.
• AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS
OUVRIR
Mains plug is used as disconnect device and it should
remain readily operable during intended use. In order
to disconnect the apparatus from the mains completely,
the mains plug should be disconnected from the mains
socket outlet completely.
La prise du secteur est utilisé pour déconnecter le
système.
La prise du secteur ne doit pas être obstruée ou doit être
facilement accessible pendant son utilisation. Pour être
complètement déconnecté de l’alimentation d’entrée, la
prise doit être débranchée du secteur.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or
rechargeable (ni-cad, ni-mh, etc) batteries.
No mezcle baterías viejas y nuevas.
No mezcle baterías alcalinas, estándar (carbono-zinc) o
recargables (ni-cad, ni-mh, etc.).
• CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
• WARNING:To reduce the risk of re or electric shock,
do not expose this apparatus to rain or moisture.
• AveRTIssemeNT: Pour réduire le risque d’incendie
ou de choc électrique, ne pas exposer cet appareil sous la
pluie et l’humidité.
• CAUTION: Use of any controls or adjustments or
performance of procedures other than those herein
specied may result in hazardous radiation exposure.
• WARNING: Changes or modications to this unit
not expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
• WARNING: Do not place the unit on top of any soft,
porous, or sensitive surfaces to avoid damaging the
surface. Use a protective barrier between the unit and
surface to protect the surface.
• WARNING: Use of this unit near uorescent lighting
may cause interference regarding use of the remote. If
the unit is displaying erratic behavior move away from
any uorescent lighting, as it may be the cause.
• CAUTION:Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent type.
• PRÉCAUTION: Danger d’explosion si les piles sont
remplacées de façon incorrect. Remplacer les piles
seulement par le même type de pile ou l’équivalent.
• WARNING: There is a danger of explosion if you
attempt to charge standard Alkaline batteries in the unit.
Only use rechargeable NiMH batteries.
• WARNING: The remote control’s button cell battery
contains mercury. Do not put in the trash, instead recycle
or dispose of as hazardous waste
Warnings and Precautions
The lightning ash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of
sufcient magnitude to constitute a risk of electric
shock to persons.
WARNING: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
ATTENTION
RISQUE D' ÉLECTROCUTION
NE PAS OUVRIR
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
Customer Support: 1-888-999-4215 3
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualied service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
WARNING: Changes or modications to this unit not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• The apparatus shall not be exposed to dripping or splashing and
that no objects lled with liquids, such as vases, shall be placed on
apparatus.
L’appareil ne doit pas être exposé aux écoulements ou aux
éclaboussures et aucun objet ne contenant de liquide, tel qu’un vase,
ne doit être placé sur l’objet.
• Main plug is used as disconnect device and it should remain readily
operable during intended use. In order to disconnect the apparatus
from the mains completely, the mains plug should be disconnected
form the mains socket outlet completely.
La prise du secteur ne doit pas être obstruée ou doit être facilement
accessible pendant son utilisation. Pour être complètement
déconnecté de l’alimentation d’entrée, la prise doit être débranchée
du secteur.
• Battery shall not be exposed to excessive heat such as sunshine, re
or the like.
Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à la
lumière du soleil, au feu ou autres choses de semblable.
• Caution marking is located at the rear or back of the apparatus.
Attention marquage est situé à l’arrière ou à l’arrière de l’appareil
• The marking information is located at the rear or back of apparatus.
Les informations de marquage est situé à l’arrière ou à l’arrière de
l’appareil.
FCC Warnings
Additional Warnings
1. Read these Instructions.
2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding - type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety.
When the provided plug does not t into your outlet,
consult an electrician for replacement of the obsolete
outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specied by the
manufacturer.
12.
Important Safety Instructions
This symbol indicates that this product
incorporates double insulation between
hazardous mains voltage and user
accessible parts.
Use only with a cart, stand, tripod,
bracket, or table specied by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
4
• Made for iPod
• Plays and charges iPod
• Motoried dock for iPod
• 2.1 channel system
• Magnetically shielded full-range stereo
speakers
• Integrated subwoofer
• AM/FM radio
• Station memory presets (10)
• Digital clock
• Timer
• LCD display with white backlight
• Composite video output
• 3.5mm audio input
• 2 RCA stereo inputs
• RCA stereo outputs
• Subwoofer output
• Bass and treble controls
• Remote control: requires 2 AAA
batteries (included)
• AC power: built-in AC power cable
• Dock adapters for iPod
• AM loop antenna
• FM wire antenna
• Remote control: requires 2 AAA
batteries (included)
• Wall-mount hardware
Bar Speaker for iPod
Features
Included
Customer Support: 1-888-999-4215 5
Table of Contents
Bar Speaker for iPod ............................................................... 4
Features
Included
Table of Contents .................................................................. 5
Introduction ...................................................................... 6
Setup ............................................................................. 8
Power
Remote Power
iPod .............................................................................. 9
Docking an iPod
Playing a Docked iPod
Clock ............................................................................10
Setting the Clock
Radio ............................................................................11
Tuning the AM/FM Radio
Saving a Station as a Preset from the Bar Speaker
Saving a Station as a Preset from the Remote
Video ............................................................................12
Composite Video Output
Audio ............................................................................13
RCA Stereo Audio Inputs
3.5mm Audio Input
Mounting the Bar Speaker ........................................................14
Important Notes
Required Tools
Included Hardware
Getting Started
Company Information ............................................................16
International Support
Contact Information
6
Introduction
LCD DISPLAY
MOTORIZED DOCK
FOR iPod
COMPOSITE VIDEO
OUTPUT
RESET BUTTON
Press the Reset
Button using a paper
clip or like object to
restore the unit to it’s
default settings.
POWER
Press to turn the unit o
and on.
VOLUME
Press to adjust the
volume of the audio
output from the unit
TUNING
Press to adjust the AM
or FM radio frequency.
3.5MM AUDIO INPUT
SUBWOOFER OUTPUT
RCA STEREO AUDIO
OUTPUTS
RCA STEREO AUDIO
INPUTS
FM ANTENNA
CONNECTION
AM ANTENNA
CONNECTION
SOURCE
Press to switch between
AM/FM radio, iPod, AV1,
and AV2 modes.
PLAY/PAUSE
Press to play or pause
an iPod. In radio mode,
press the Play/Pause
Button repeatedly to
cycle through the saved
radio stations.
iPod DRAWER
Press to open or close
the Motorized Dock for
iPod.
Customer Support: 1-888-999-4215 7
MUTE
Press to decrease the
audio output volume
on the unit entirely.
POWER
Press to turn the unit o
and on.
NUMBER KEYPAD
ALBUM/CHAPTER/
PLAYLIST
Press to cycle through
albums, chapters, and
playlists on a docked
iPod.
SLEEP
Press to activate the
sleep timer. Using
the FWD Button, the
sleep timer can be
set anywhere from 10
to 240 minutes, in 10
minute increments.
DIRECTIONAL REV,
FWD, SKIP, SEARCH,
TUNING, AND
NAVIGATION
Press to navigate a
docked iPod’s menu,
skip through tracks, or
tune the AM/FM radio.
Press and hold to search
through an individual
track.
TREBLE
Press to adjust the
treble of the unit.
PLAY/PAUSE/TIME
SET
Press to play or pause a
docked iPod. With the
unit powered o, press to
begin setting the clock.
SOURCE
Press to switch between
AM/FM radio, iPod, AV1,
and AV2 modes.
iPod DRAWER
Press to open or close
the Motorized Dock for
iPod.
MENU
Press to return to a
previous menu on a
docked iPod. In radio
mode, press the Menu
Button to cycle through
saved radio stations.
REPEAT/ST
Press to repeat a single
track or an entire album
from a docked iPod.
Press to switch the FM
radio between stereo
and mono.
VOLUME
Press to adjust the
volume of audio output
of the unit
CLOCK VIEW/
DIMMER/RANDOM
Press to view the clock
when in radio mode, or
play songs randomly in
iPod mode. Press and
hold to dim the LCD
display.
SELECT
Press to make selections
on a docked iPod.
BASS
Press to adjust the bass
of the unit.
FUNCTION
REPEAT/ST
VOLUME
MENU
TIME SET
MUTE
SLEEP
BASSTREBLE
CLOCK VIEW/
DIMMER
8
Plug the attached AC cord into a standard
AC power outlet to power the bar speaker.
Requires 2 AAA batteries (included)
Power
Remote Power
Setup
PB
Customer Support: 1-888-999-4215 9
Docking an iPod
1. Locate the numbered adapter that ts
the iPod that will be docked.
Each included adapter has a number
on it, indicating which iPod model that
adapter is compatible with. See the
separate adapter chart to identify which
adapter is needed.
2. Press the iPod DRAWER button to
open the MOTORIZED DOCK FOR
iPod.
3. Snap the adapter into place over the
iPod connector in the dock.
4. Connect the iPod to the connector
inside the Dock for iPod.
5. When the dock is plugged in, using AC
power, the docked iPod will charge.
After removing the iPod from the
MOTORIZED DOCK FOR iPod, press the
iPod DRAWER button to close the dock.
Playing a Docked iPod
1. Follow the instructions for Docking an
iPod.
2. Press the SOURCE button to switch to
iPod mode.
3. Press the PLAY/PAUSE button to begin
playing the docked iPod.
iPod
10
Clock
1. With the unit powered o, press the
TIME SET button on the remote
The hour will begin to blink on the LCD
display, indicating it can be adjusted.
2. Press the FWD and RWD buttons to
adjust the hour.
3. Press the TIME SET button.
The minute will begin to blink, indicating
it can be adjusted.
4. Press the FWD and RWD buttons to
adjust the minute.
5. Press the TIME SET button to nished
setting the clock.
Setting the Clock
Customer Support: 1-888-999-4215 11
Radio
1. Press the POWER button to turn the
bar speaker on.
2. Press the SOURCE button to switch
the bar speaker to radio mode.
An AM or FM will appear on the LCD
Display to indicate radio mode.
3. Press the TUNING buttons to tune the
AM or FM radio.
1. Follow the instructions for Tuning the
AM/FM Radio.
2. Press and hold the PLAY button.
The LCD display will show “MEM 01”.
(“MEM” will ash)
3. Press the PLAY button repeatedly to
select from MEM 01 to MEM 10.
4. Press and hold the PLAY button to
save the current radio frequency to the
selected memory station.
5. Press the PLAY button repeatedly to
select stored radio stations.
1. Follow the instructions for Tuning the
AM/FM Radio.
2. Press and hold the MENU button.
The LCD display will show “MEM 01”.
(“MEM” will ash)
3. Press the MENU button repeatedly to
select from MEM 01 to MEM 10.
4. Press and hold the MENU button to
save the current radio frequency to the
selected memory station.
5. Press the MENU button repeatedly to
select stored radio stations.
Tuning the AM/FM Radio Saving a Station as a Preset from the
Bar Speaker
Saving a Station as a Preset from the
Remote
12
Video
When connecting two products using an
RCA Cable, match the colored ports with
the same colored connection. (Red to Red,
White to White, and Yellow to Yellow)
1. Connect the RCA Cable to the Stereo
RCA Outputs and RCA Composite
Video Output on the unit, and to the
audio/video inputs on the Television.
2. Turn the unit on by pressing the
POWER button.
3. Change the television to the correct
audio/video input setting.
4. Audio and video played through the
unit will now be seen and heard on the
connected television.
Composite Video Output
PB
Audio In Video In
Customer Support: 1-888-999-4215 13
Audio
1. Attached a 3.5mm audio cable to the
LINE INPUT on the bar speaker and an
audio output on an MP3 player or ther
audio source.
2. Press the POWER button to turn the
unit on.
3. Press the SOURCE button to switch
the unit to AV 2 mode.
4. Audio played from the Mp3 Player or
Other Audio Source will now be heard
on the unit.
If connecting to the headphone output
of an audio source, the source’s volume
controls may need to be adjusted for
optimal sound.
When connecting two products using an
RCA Cable, match the colored ports with
the same colored connection. (Red to Red,
White to White, and Yellow to Yellow)
1. Connect a stereo RCA cable (not
included) to the RCA STEREO AUDIO
INPUTS on the unit and the stereo
RCA outputs on a television or sound
system.
2. Turn the unit on by pressing the
POWER button.
3. Press the SOURCE button to change
the unit to AV1 if the stereo RCA cable
is connected to IN1. Change the
unit to AV2 if the stereo RCA cable is
connected to IN2.
4. Audio played through the connected
television or sound system will now be
heard through the unit.
3.5mm Audio Input
RCA Stereo Audio Inputs
Television, DVD Player,
Set-Top Box, or Game System
Audio Out Audio Out
14
Mounting the Bar Speaker
We recommend having this bar speaker
professionally mounted.
The included spacers should be used at
your discretion to extend the face of the
bar speaker farther from the wall. These
are typically used when mounting the bar
speaker under a television, and the face of
the bar speaker needs to be ush with the
face of the television.
• Manual or Power Screwdriver
• Stud Finder
• Pencil
• Tape Measure
• Level
• (2) Wall Mount Brackets
• (4) Long Screws
• (4) Short Screws
• (2) Spacer Inserts
• (2) 1/4” Spacers
• (2) 1/2” Spacers
• (2) 3/4” Spacers
• (2) 1” Spacers
Important Notes
Required Tools
Included Hardware
Customer Support: 1-888-999-4215 15
1. Use the TAPE MEASURE to decide how
high you’d like to hang the bar speaker
on the wall.
The bar speaker must be hung within
6 feet of an AC power outlet for the
attached AC power cable to reach.
2. Use the STUD FINDER to locate 2
parallel wooden studs to screw the
mounting brackets into.
3. Mark the wall at the center of the studs
using the PENCIL.
4. Line the level up on both of your marks
to make sure they are level. If they’re
not, adjust the marks as needed to
make them level.
5. After you’ve double checked your
markings, DRILL through the top hole
on both mounting brackets directly
into the marks you’ve made on the
wall.
6. If you are using the brackets only and
no spacers, use the included short
screws. If you are using any of the
spacers or combination of the spacers,
use the long screws.
7. Use the LEVEL to level each of the
hanging brackets, then drill the second
screw into the bottom hole on both
mounting brackets.
8. Slide the bar speaker onto the
mounting brackets, and make sure
there is a rm and stable connection
before letting go of the bar speaker.
9. Finally, use the LEVEL to conrm that
the bar speaker is level.
Getting Started
16”
IT188B
IT188B
screws
studs
mounting
bracket
spacer
Copyright © 2010 Digital Products International (DPI, Inc.) | All other trademarks appearing herein are the property of their respective
owners. Specications are subject to change without notice
To download this User’s Guide in English,
Spanish, or French, visit the support section
at www.ilive.net.
Para transferir esta guía de usuario en
inglés, español, o francés, visite la sección
de la ayuda en www.ilive.net.
Pour télécharger ce guide de l’utilisateur
en anglais, espagnol, ou français, visitez la
section de soutien chez www.ilive.net.
Phone: 1-888-999-4215
Email: [email protected]
Parts Email: partsinfo@dpi-global.com
Website: www.ilive.net
International Support
Contact Information
Company Information
Other manuals for IT188B
3
Table of contents
Other iLive Home Cinema Speakers manuals
