Incra Wheel Kit User manual
Assembly Instructions
INCRA Wheel Kit
1Assembly Instructions for the INCRA Wheel Kit
Fig. 1 Wheel Kit
www.incra.com
(1) Front Wheel Connector Bracket
(1) Front Wheel Pedestal
(1) Front Wheel Foot Pedal
(1) Front Wheel Caster
(2) Leg Wheel Bracket
(2) Leg Wheel
(8) 1/4-20 x 1/2 Hex Bolt
(2) 1/4-20 x 2 1/4 Hex Bolt
(6) 5/16-18 x 1/2 Hex Bolt
(2) 5/16-18 x 3 3/4 Hex Bolt
(8) 1/4-20 Square Nut
(2) 1/4-20 Locking Nut
(6) 5/16-18 Hex Nut
(2) 5/16-18 Locking Nut
(11) 1/4” Flat Washer
(4) 1/4” Lock Washer
(4) 1/4 id x 1/4 Thick Nylon Washer
(4) 5/16 id x 3/16 Thick Nylon Washer
Parts List:
Step 1. Assemble Leg Wheels.
First, loosley install two sets of 1/4-20 x 1/2 bolts, 1/4-20 square
nuts and 1/4” washers in each wheel bracket as shown in Fig. 2.
Second, install a rubber wheel in the lower hole on each wheel
bracket using the 1/4-20 x 2 1/4 hex bolt, 1/4-20 locking nut, 1/4”
steel washer and 1/4” thick Nylon washers as shown in Fig. 2.
Be sure that the two 1/4” thick Nylon washers are against the hub
of the wheel and positioned INSIDE the wheel bracket. Install,
but do not fully tighten the locking nut on the 2 1/4 hex bolts
at this time.
Step 2. Install Leg Wheels on Legs.
Orientation: When mounting the stand to offset tables, the two
leg wheels should be located under the end of the table WITH
the router cutout in it. For center mount router tables, the two
leg wheels can be on either end of the table.
Remove the levelers from the two legs on which the wheels will
be installed. As shown in Fig. 3, slide the (2) square nuts and
the long hex bolt head on each wheel assembly into the T-slot
on the leg extrusion. Adjust the vertical position of each wheel
for stability, then firmly tighten all bolts. Tighten the locking nut
enough to remove all side play between the wheel and the
inside of the wheel bracket, but still loose enough for the wheel
to pivot freely.
Fig. 2 Assemble Leg Wheels
Fig. 3 Install Leg Wheels
Table Stand Legs
Leg Wheel (2)
Wheel Stringer on Table Stand
Leg Wheel Bracket (2)
Front Wheel Foot Pedal
Front Wheel Caster
Front Wheel Pedestal
Front Wheel Connector Bracket
Leg Wheel Bracket
Wheel
1/4-20
Square Nut
1/4-20 x 21/4
Hex Bolt
1/4“ Thick Nylon Washer
1/4“ Thick Nylon Washer
1/4“ Washer
1/4-20
Locking Nut
1/4-20 x 1/2
Hex Bolt (4)
1/4“ Washer (4)
Outfeed Wheel
Assembly
Capture Square
Nuts & Hex Bolt
in T-Slot on Leg
Infeed Wheel
Assembly
Leg Wheel (2)
INCRA Wheel Kit Assembly Instructions
Step 3. Install connector bracket on wheel stringer.
Orient the front wheel connector bracket as shown in Fig. 4,
then attach it to the wheel stringer using 1/4-20 x 1/2 hex bolts,
1/4” washers, 1/4” lock washers and 1/4-20 square nuts.
Step 4. Install caster on front wheel pedestal.
Using 5/16-18 hex bolts and 5/16-18 hex nuts, attach the swivel
caster to the underside of the front wheel pedestal as shown in
Fig. 5.
Step 5. Attach assembled front wheel pedestal to connector bracket.
Attach the assembled front wheel pedestal to the lower holes in
the connector bracket by using a 5/16-18 x 3 3/4 hex bolt and
5/16-18 locking nut, Fig. 6. The front wheel pedestal must pivot
freely. Do not overtighten.
Step 6. Install NYLON washers on foot pedal.
Attach two of the 3/16” thick NYLON washers to the outside of
the foot pedal using 5/16-18 x 1/2 hex bolts and 5/16-18 hex nuts
through the holes indicated in Fig. 7. Tighten securely.
Fig. 4 Install Connector Bracket Fig. 5 Install Caster
Fig. 6 Install Front Wheel Pedestal Fig. 7 Install Nylon Washers
Step 7. Attach foot pedal to connector bracket.
Attach foot pedal to the upper holes in the connector bracket
by using a 5/16-18 x 3 3/4 hex bolt, 5/16-18 locking nut and two
3/16” thick Nylon washers, Fig. 8. The foot pedal must pivot
freely. Do not overtighten.
Step 8. Operation and adjustments.
Engage the swivel caster by pushing down on the front end of
the foot pedal with your foot. Disengage the caster by pushing
down on the other end of the foot pedal with your foot, Fig. 9.
Fig. 8 Install Foot Pedal Fig. 9 Adjustments
1/4-20 Square Nut
1/4” Lock Washer
Wheel Stringer
Front Wheel
Connector Bracket
1/4-20 x 1/2 Hex Bolt
1/4” Washer
5/16-18 x 1/2 Hex Bolt
Front Wheel Pedestal
5/16-18 Hex Nut
Front Wheel
Connector Bracket
5/16-18 x 3 3/4 Hex Bolt
Assembled Front
Wheel Pedestal
5/16-18 Locking Nut
5/16-18 x 1/2
Hex Bolt
3/16“ Thick Nylon
Washer
5/16-18 Hex Nut
Foot Pedal
3/16“ Thick Nylon Washer
Note: TWO washers. One on
each side of foot pedal.
Foot Pedal
5/16-18 x 3 3/4 Hex Bolt
5/16-18 Locking Nut
Adjust Vertical Position
of Leg Wheels for
Stability
Adjust the height of the
wheel stringer and the
leg levelers on either
side of the swivel caster
so that the leveler pads
are OFF the oor when
the foot pedal is en-
gaged, and on the oor
when the foot pedal is
disengaged.
Push foot pedal
down here with your
foot to engage the
swivel caster.
Push other end to
disengaged.
Wheel
Stringer
Manufactured by:
Taylor Design Group, Inc.
P.O. Box 810262 Dallas, TX 75381
www.incra.com P: 972-242-9975/F: 972-242-9985
INCRA is a Registered Trademark of Taylor Design Group, Inc.
You can also register your INCRA product online at www.incra.com
Scan this QR code to register your product online
It’s quick and easy!
ONLINE WARRANTY REGISTRATION
MADE IN THE
USA
2
