Vivo MOUNT-SF05H User manual

Wall Brackets for Floating Shelf - 4 Pack
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-sf05h
SKU: MOUNT-SF05H
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
ASSEMBLY STEPS
STEP 1
Insert the set screws (B) into the wall
plates (C) until the ends of the screws
are flush with the backs of the plates.
PACKAGE CONTENTS
TOOLS NEEDED
10lbs
(4.53kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
A (x4)
Hex Rod
B(x4)
Set Screw
C(x4)
Wall Plate
D (x8)
M5x40
E (x8)
Anchor
F (x1)
Allen
Wrench
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
Drill Pencil Level
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
NOTE: SOME HARDWARE MAY NOT BE USED
PER BRACKET

3
STEP 2
While holding set screw position with the Allen
wrench (F), screw the hex rods (A) tightly in place.
STEP 3
OPTION A: Wood Stud Wall
Place mounts on the wall at the
desired locations with the mounting
holes positioned horizontally, and
mark drilling locations with a pencil.
Use of a stud finder and level is
recommended. Drill 1.55” (40mm)
deep holes using a 5/32” (4mm) drill
bit. Attach mounts to wall using
M5x40 screws (D).
If stud width is less than the hole
spacing of the mount, drill one hole
into the center of the stud and refer to
OPTION B for the second hole.
OPTION B: Brick/Concrete Wall
or Drywall
Place mounts on the wall at the desired
locations with the mounting holes
positioned horizontally, and mark drilling
locations with a pencil. Use of a level is
recommended. Drill 1.75” (45mm) deep
holes using a 5/16” (8mm) drill bit. Insert
anchors (E) into holes, then attach mounts
to wall using M5x40 screws (D).
STEP 4
Mark drilling locations on the rear edge of the shelf,
making sure spacing is identical to the mounted
brackets. Using a 1/2” (13mm) bit, drill holes 5.25”
(134mm) deep into the shelf, making sure holes are
drilled completely straight. Slide shelf onto mounts.

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303