Indesit WIXE 127 User manual

1
GB
English,1
Contents
Installation, 2-3-4-5
Unpacking and levelling
Electric and water connections
The first wash cycle
Technical details
Washing machine description, 6-7
Control panel
Display
MEMO Programme
tarting and Programmes, 8
riefly: how to start a programme
Programme table
Personalisations, 9
Setting the spin cycle
Setting the Delay Timer
Setting the temperature
Functions
Detergents and laundry, 10
Detergent dispenser
leach cycle
Preparing your laundry
Special items
Precautions and advice, 11
General safety
Disposal
Saving energy and respecting the environment
Care and maintenance, 12
Cutting off the water or electricity supply
Cleaning your appliance
Cleaning the detergent dispenser
Caring for your appliance door and drum
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 13-14
Assistance, 15-16
WA HING MACHINE
WIXE 127
Instructions for use
GB

2
GB
Installation
Keep this instruction manual in a safe place for
future reference. Should the appliance be sold,
transferred or moved, make sure the instruction
manual accompanies the washing machine to inform
the new owner as to its operation and features.
Read these instructions carefully: they contain vital
information on installation, use and safety.
Unpacking and levelling
Unpacking
1. Unpack the washing machine.
2. Check whether the washing machine has been
damaged during transport. If this is the case, do not
install it and contact your retailer.
3. Remove the 3
protective screws and
the rubber bush with the
respective spacer,
situated on the rear of
the appliance (see also
the installation leaflet).
4. Seal the gaps using the plastic plugs provided.
5. Keep all the parts: you will need them again if the
washing machine needs to be moved to another
location.
Packaging materials are not children's toys.
Levelling
Your machine may make a considerable amount of noise
if the two front feet have not been adjusted correctly.
1. Install the washing machine on a flat sturdy floor,
without resting it up against walls, furniture cabinets
or other.
2. If the floor is not
perfectly level, compen-
sate for any
unevenness by
tightening or loosening
the adjustable front feet
(see figure); the angle of
inclination, measured
according to the
worktop, must not
exceed 2°.
Levelling your appliance correctly will provide it with
stability and avoid any vibrations, noise and shifting
during operation. If it is placed on a fitted or loose
carpet, adjust the feet in such a way as to allow
enough room for ventilation beneath the washing
machine.
Electric and water connections
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it to a
cold water tab using a
3/4 gas threaded
connection (see figure).
efore performing the
connection, allow the
water to run freely until
it is perfectly clear.
2. Connect the other end
of the water inlet hose to
the washing machine,
screwing it onto the
appliance's cold water
inlet, situated on the top
right-hand side on the
rear of the appliance
(see figure).
3. Make sure there are no kinks or bends in the hose.
The water pressure at the tap must be within the
values indicated in the Technical details table
(on the next page).
If the water inlet hose is not long enough, contact
a specialist store or an authorised serviceman.
Ensure that the supply taps are allowing water
through. Old taps may seize in the closed position
and thus prevent water reaching the machine.

3
GB
Connecting the drain hose
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between
65 and 100 cm from
the floor;
The drain hose may be
connected to an
under-sink trap. efore
connecting the drain
hose from the machine
ensure that any blanks
or removable ends
have been taken off
the spigot.
If it is place over the
edge of a basin or sink
be sure the free end of
the hose should not be
underwater.
 We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Ensure that if the drain hose is pushed into a
standpipe, that the end does not go down more
than 15cms (6 inches). If the hose is pushed down
too far, this may cause the machine to self -syphon
ie. continuously empty as it is filling.
Electric connection
efore plugging the appliance into the mains
socket, make sure that:
 the socket is earthed and in compliance with the
applicable law;
 the socket is able to sustain the appliance's
maximum power load indicated in the Technical
details table (see page 5);
 the supply voltage is included within the values i
ndicated on the Technical details table
(see page 5);
 the socket is compatible with the washing
machine's plug. If this is not the case, replace
the socket or the plug.
Your appliance is now supplied with a 13 amp fused
plug it can be plugged into a 13 amp socket for
immediate use. efore using the appliance please
read the instructions below.
WARNING - THIS APPLIANCE MUST E EARTHED.
THE FOLLOWING OPERATIONS SHOULD E
CARRIED OUT Y A QUALIFIED ELECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to S 1362 should always be used,
and the fuse cover re-fitted. If the fuse cover is lost,
the plug must not be used until a replacement is
obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the
correct colour as indicated by the coloured marking
or the colour that is embossed in words on the base
of the plug. Replacements can be obtained directly
from your nearest Service Depot.
Removing the plug:
If your appliance has a non-rewireable moulded plug
and you should wish to re-route the mains cable
through partitions, units etc., please ensure that
either:
the plug is replaced by a fused 13 ampere re-
wearable plug bearing the SI mark of approval.
or:
the mains cable is wired directly into a 13 amp cable
outlet, controlled by a switch, (in compliance with S
5733) which is accessible without moving the
appliance.
Disposing of the plug:
Ensure that before disposing of the plug itself, you
make the pins unusable so that it cannot be
accidentally inserted into a socket.
Instructions for connecting cable to an alternative plug:
Important: the wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow Earth
Blue Neutral
Brown Live
65 - 100 cm
Where it connects to
the waste water pipe
cut end off spigot or
remove the blanking cap

4
GB
GREEN &
YELLOW
BROWN
BLUE
13 ampere fuse
CROSS-BAR
CORD GRIP
As the colours of the wires in the lead may not
correspond with the coloured markings identifyng
the terminals in your plug, proceed as follows:
Connect Green & Yellow wire to terminal marked E
or or coloured Green or Green & Yellow.
Connect rown wire to terminal marked L or
coloured Red.
Connect lue wire to terminal marked N or coloured
lack.
If a 13 amp plug ( S 1363) is used it must be fitted
with a
13 amp fuse, either in the plug or adaptor or at the
distribution board.
If you are in any doubt the electrical supply to your
machine, consult a qualified electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in
accordance with the following code:
BLUE NEUTRAL (N)
BROWN LIVE (L)
GREEN & YELLOW EARTH (E)
Disposing of the appliance:
When disposing of the appliance please remove the
plug by cutting the mains cable as close as possible
to the plug body and dispose of it as described
above.
 The washing machine should not be installed in an
outdoor environment, not even when the area is
sheltered, because it may be very dangerous to
leave it exposed to rain and thunderstorms.
 When the washing machine is installed, the mains
socket must be within easy reach.
 Do not use extensions or multiple sockets.
 The power supply cable must never be bent or
dangerously compressed.
 The power supply cable must only be replaced by
an authorised serviceman.
Warning! The company denies all liability if and when
these norms are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, setting the 90°C
programme without a pre-wash cycle.

5
GB
Technical details
Model WIXE 127
Dimensions
59.5 cm wide
85 cm high
52.5 cm deep
Capacity from 1 to 6 kg
Electric
connections
please refer to the technical data plate
fixed to the machine
Water
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 46 litres
pin speed up to 1200 rpm
Control
programmes
according to
EN 60456
directive
programme 2; temperature 60°C;
run with a load of 6 kg.
This appliance is compliant with the
following European Community
Directives:
- 2004/108/CE (Electromagnetic
Compatibility)
- 2002/96/CE
- 2006/95/CE (Low Voltage)

6
GB
Control panel
Washing machine description
Control knob
Display
Detergent dispenser
PIN
button
TEMPERATURE
button
TART/ TOP
button
TART/RE ET
button
Detergent dispenser to add detergent and fabric
softener (see page 10).
PIN button to adjust the spin speed or exclude it
altogether (see page 9).
DELAY TIMER button to delay the start of the set
programme for a maximum period of 24 hours
(see page 9).
TEMPERATURE button to adjust the wash tempe-
rature (see page 9).
Display to programme the washing machine and
follow the wash cycle progress (see opposite page).
FUNCTION buttons: to select the functions
available. The button corresponding to the function
selected will remain on.
TART/RE ET button to start the programmes or
cancel any incorrect settings.
TART/ TOP button to turn the washing machine
on and off.
Control knob to select the wash programmes.
The knob stays still during the cycle.
DELAY TIMER
button
FUNCTION
uttons

7
GB
Display
In addition to being a practical tool to programme your appliance (see page 9), the display provides useful
information concerning the wash cycle.
Once you have pressed the START/RESET button to
start the programme, the display will indicate the
amount of time left until the end of the wash cycle. If
a delayed start has been set (using the Delay Timer,
see page 9), the delay time will be indicated on the
display.
Door lock:
If the symbol is on, the washing machine door is locked to prevent it from being opened accidentally. To avoid
any damages, wait for the symbol to switch itself off before you open the appliance door.
At the end of the programme, the word END is displayed.
 In the event of an anomaly, an error code will appear, such as: F-01, (see page 13).
"MEMO" Programme
This programme allows you to store your favourite or most-used wash cycle.
All you have to do is set the desired programme and, once it has started, turn the KNO to position ; the
wash cycle will be stored automatically and the word MEMO appears on the display, flashing for a few seconds.
Subsequently, you can start the "MEMO" cycle by simply turning the KNO to position ; you will be able to
see the temperature/spin cycle/delay timer values by pressing the corresponding buttons; you will also be able to
modify them but this variation will only be valid for the programme in progress and it will not be stored in the
"MEMO" cycle.
If you want to store a new wash cycle, repeat the above-mentioned operations.

8
GB
Type of fabric and
degree of soil Progr. Te m p e - rature
Detergent Fabric
softener
Stain removal
option/bleach Description of wash cycle
Ma .
Spin
Speeds
(r.p .m .)
Cycle
length
(minutes)
pre-
wash wash
tandard
Cotton: Extremely soiled whites
(sheets, tablecloths, etc.) 190°C    Pre-wash, wash cycle, rinse cycles,
intermediate and final spin cycles Max.
Cotton: Extremely soiled whites
(sheets, tablecloths, etc.) 290°C   Delicate/
Traditional Wash cycle, rinse cycles, intermediate and final spin cycles Max.
Cotton: Heavily soiled whites
and fast colours 260°C   Delicate/
Traditional Wash cycle, rinse cycles, intermediate and final spin cycles Max.
Cotton: Heavily soiled whites
and delicate colours 240°C   Delicate/
Traditional Wash cycle, rinse cycles, intermediate and final spin cycles Max.
C otton: Slightly soiled whites
and delicate colours (shirts,
jumpers, etc.) 340°C   Delicate/
Traditional Wash cycle, rinse cycles, intermediate and final spin cycles Max.
Synthetics: Heavily soiled
fast colours (baby linen, etc.) 450°C   Delicate Wash cycle, rinse cycles, anti-
crease or delicate spin cycle 800
Synthetics: Heavily soiled
fast colours (baby linen, etc.) 440°C   Delicate Wash cycle, rinse cycles, anti-
crease or delicate spin cycle 800
Wool 540°C   Wash cycle, rinse cycles and
delicate spin cycle 600
Very delicate fabrics
(curtains, silk, viscose, etc.) 630°C   Wash cycle, rinse cycles, anti-
crease or draining cycle no
Time 4 you
C otton: Heavily soiled whites
and fast colours 760°C   Wash cycle, rinse cycles,
intermediate and final spin cycles Max.
C otton: Slightly soiled whites
and delicate colours (shirts,
jumpers, etc.) 840°C   Wash cycle, rinse cycles,
intermediate and final spin cycles Max.
Synthetics: Delicate colours (all
types of slightly soiled garments) 940°C  Wash cycle, rinse cycles,
delicate spin cycle 800
Synthetics: Delicate colours (all
types of slightly soiled garments) 10 30°C   Wash cycle, rinse cycles and
delicate spin cycle 800
port
Sports shoes (MAX. 2 pairs) 11 30°C  Cold wash (without detergents),
wash cycle, rinse cycles, and
delicate spin cycle 800
Fabrics for sportswear
(Tracksuits, shorts, etc.) 12 30°C   Wash cycle, rinse cycles,
intermediate and final spin cycles 600
MEMO Allows for any wash cycle to be stored (see pag. 7)
PARTIAL PROGRAMME
Rinse  Delicate/
Traditional Rinse cycles and spin cycle 800
Spin Draining and spin cycle 800
Drain Draining no
tarting and Programmes
Programme table
Notes
-For programmes 7 and 8, we advise against exceeding a wash load of 3.5 kg.
-For programme 12 we advise against exceeding a wash load of 2 kg.
-For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative.
pecial programme
Dail (programme 10 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts
30 minutes and allows you to save on both time and energy. y setting this programme (10 at 30°C), you can wash
different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.
We recommend the use of liquid detergent.
Briefly: starting a programme
1. Turn the washing machine on by pressing button .
2. Load your laundry into the washing machine and
shut the appliance door.
3. Set the knob to the desired programme. The
estimated duration of the selected programme is
displayed. The temperature and spin speed are
automatically set according to the programme
(to change them, see page 9).
4. Select any functions (see page 9).
5. Add the detergent and any fabric softener
(see page 10).
6. Start the programme by pressing the START/RESET
button for one second.
To cancel it, keep the START/RESET button
pressed for at least 2 seconds.
7. When the programme has ended, the word END is
displayed. Take out your laundry and leave the
appliance door ajar to allow the drum to dry
thoroughly.
8. Turn the washing machine off by pressing button .
The duration of the wash cycles can be checked on the display.

9
GB
Function Effect Comments Enabled with
programmes:
Stain
removal
leaching cycle
designed to
remove the
toughest stains.
Please remember to pour the bleach into extra compartment 4
(see page 10).
This function is incompatible with the EASY IRON function.
2, 3, 4,
Rinse cycle.
Extra Rinse
Increases the
efficiency of the
rinse.
Recommended when the appliance has a full load or with large
quantities of detergent.
1, 2, 3, 4, 7,
8, 9, 11, 12,
Rinse cycle.
Easy iron
This option
reduces the
amount of
creasing on
fabrics, making
them easier to
iron.
When this function is set, programmes 4 and 6 will end, with the
laundry left to soak (Anti-crease), and the relative button flashes:
- to conclude the cycle, press the START/RESET button or the
EASY IRON button;
- to run the draining cycle alone, set the knob to the relative
symbol and press the START/RESET button.
This function is incompatible with the STAIN REMOVAL function.
3, 4, 6, 7, 8, 9,
Rinse cycle.
Personalisations
etting the spin cycle
If, when the appliance is switched on, the KNO is positioned on
a programme with a spin cycle, a fixed appears. Press button
and the maximum spin speed allowed for the programme set
will be displayed, and the icon flashes. Press it again and the
values lower until they reach OFF, which indicates that the spin
cycle has been excluded (press it again to go back to the
maximum value); stop on the desired speed, after approximately
2 seconds the setting is accepted: the symbol remains fixed.
The spin cycle setting is enabled with all the programmes except
for 6 and the Draining cycle.
etting the Delay Timer
Press the button and you will see the word OFF on the
display, while the relative symbol flashes.
Press the button again and "1h" appears, that is, a delay of one
hour (this can reach up to 24h); stop on the "desired" delay; after
approximately 2 seconds the setting is accepted, following which,
the time for the set programme appears on the display and the
symbol remains on.
If you now press the START/RESET button, the set "delay"
appears; this decreases every hour until the start of the cycle. In this phase, the "delay" can only be modified by
decreasing it. The Delay Timer regulation is enabled with all programmes.
etting the temperature
If, when the appliance is switched on, the KNO is positioned on a programme for which the temperature needs
to be regulated, a fixed appears. Press button and the maximum temperature allowed for the programme set
will be displayed and the icon flashes. Press it again and the temperature lowers until it reaches OFF, which
indicates a cold wash cycle (press it again to go back to the maximum value); stop on the desired value, after
approximately 2 seconds the setting is accepted: the symbol remains fixed.
The temperature adjustment is enabled with all wash programmes.
Functions
To enable a function:
1. press the button corresponding to the desired function, according to the table below;
2. the function is enabled when the corresponding button is illuminated.
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the
programme set. If you set a function that is incompatible with another function you selected previously, only the
last one selected will be enabled.
FUNCTION buttons
 The machine has an intelligent built in check for out of balance loads. To let protect your machine it may reduce the
final spin speed if an unbalanced load is detected.
The balancing attempts may extend the total duration of the cycle, up to a maximum of 10 minutes.

10
GB
Detergent dispenser
Good washing results also depend on the correct
dose of detergent: adding too much detergent won't
necessarily make for a more efficient wash, and may
in fact cause build up on the interior of your
appliance and even pollute the environment.
Open up the detergent
dispenser and pour in
the detergent and fabric
softener, as follows.
compartment 1: Detergent for pre-wash
(powder)
efore pouring in the detergent, make sure that
extra compartment 4 has been removed.
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in
immediately prior to the wash cycle start.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow from the grid.
extra compartment 4: Bleach
 Do not use hand wash detergent because it may
form too much foam.
Bleach cycle
 Traditional bleach should be used on sturdy
white fabrics, and delicate bleach for coloured
fabrics, synthetics and for wool.
Place extra
compartment 4,
provided, into
compartment 1.
When pouring in the
bleach, be careful not to
exceed the "max" level
indicated on the central
pivot (see figure).
To run the bleach cycle alone, pour the bleach into extra
compartment 4, set the Rinse programme and
enable the Stain removal function (see page 9).
To bleach during a wash cycle, pour in the detergent
and fabric softener, set the desired programme and
enable the Stain removal function (see page 9).
The use of extra compartment 4 excludes the
possibility of using the pre-wash cycle.
Preparing your laundry
 Divide your laundry according to:
- the type of fabric/the symbol on the label.
- the colours: separate coloured garments from
whites.
 Empty all pockets and check for loose buttons.
 Do not exceed the weight limits stated below,
which refer to the weight when dry:
Sturdy fabrics: max 6 kg
Synthetic fabrics: max 2,5 kg
Delicate fabrics: max 2 kg
Wool: max 1,5 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
pecial items
Curtains: fold curtains and place them in a pillow
case or mesh bag. Wash them separately without
exceeding half the appliance load. Use programme 6
which excludes the spin cycle automatically.
Quilted coats and windbreakers: if they are
padded with goose or duck down, they can be
machine-washed. Turn the garments inside out and
load a maximum of 2-3 kg, repeating the rinse cycle
once or twice and using the delicate spin cycle.
Wool: for best results, use a specific detergent,
taking care not to exceed a load of 1,5 kg.
Detergents and laundry
12
3
4

11
GB
Precautions and advice
 The washing machine was designed and built in
compliance with the applicable international safety
regulations. The following information is provided for
your safety and should consequently be read carefully.
General safety
 This appliance has been designed for non-
professional, household use and its functions must
not be changed.
 This washing machine should only be used by
adults and in accordance with the instructions
provided in this manual.
 Never touch the washing machine when barefoot
or with wet or damp hands or feet.
 Do not pull on the power supply cable to unplug
the appliance from the electricity socket. Pull the
plug out yourself.
 Do not open the detergent dispenser while the
appliance is in operation.
 Do not touch the drain water as it could reach
very high temperatures.
 Never force the washing machine door: this could
damage the safety lock mechanism designed to
prevent any accidental openings.
 In the event of a malfunction, do not under any
circumstances touch internal parts in order to
attempt repairs.
 Always keep children well away from the
appliance while in operation.
 The appliance door tends to get quite hot during
the wash cycle.
 Should it have to be moved, proceed with the
help of two or three people and handle it with the
utmost care. Never try to do this alone, because
the appliance is very heavy.
 efore loading your laundry into the washing
machine, make sure the drum is empty.
Disposal
 Disposing of the packaging material:
observe local regulations, so the packaging can
be re-used.
 The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal
waste stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the
environment. The crossed out "wheeled bin"
symbol on the product reminds you of your
obligation, that when you dispose of the appliance
it must be separately collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
aving energy and respecting the
environment
Environmentally-friendly technology
If you only see a little water through your appliance
door, this is because thanks to the latest Indesit
technology, your washing machine only needs less
than half the amount of water to get the best
results: an objective reached to respect the
environment.
aving on detergent, water, energy and time
 To avoid wasting resources, the washing machine
should be used with a full load. A full load instead
of two half loads allows you to save up to 50% on
energy.
 The pre-wash cycle is only necessary on
extremely soiled garments. Avoiding it will save on
detergent, time, water and between 5 and 15%
energy.
 Treating stains with a stain remover or leaving
them to soak before washing will cut down the
need to wash them at high temperatures. A
programme at 60°C instead of 90°C or one at
40°C instead of 60°C will save up to 50% on
energy.
 Use the correct quantity of detergent depending
on the water hardness, how soiled the garments
are and the amount of laundry you have, to avoid
wastage and to protect the environment: despite
being biodegradable, detergents do contain
ingredients that alter the natural balance of the
environment. In addition, avoid using fabric
softener as much as possible.
 If you use your washing machine from late in the
afternoon until the early hours of the morning, you
will help reduce the electricity board's peak load.
The Delay Timer option (see page 9) helps to
organise your wash cycles accordingly.
 If your laundry has to be dried in a tumble dryer,
select a high spin speed. Having the least water
possible in your laundry will save you time and
energy in the drying process.

12
GB
Care and maintenance
Cutting off the water or electricity
supply
 Turn off the water tap after every wash. This will
limit the wear of your appliance's water system
and also prevent leaks.
 Unplug your appliance when cleaning it and
during all maintenance operations.
Cleaning your appliance
The exterior and rubber parts of your appliance can
be cleaned with a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser
Remove the dispenser
by pulling it out (see
figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for your appliance door and
drum
 Always leave the appliance door ajar to prevent
unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning
pump that does not require any maintenance.
Sometimes, small items (such as coins or buttons)
may fall into the pre-chamber that protects the
pump, situated in the lower part of the same.
 Make sure the wash cycle has ended and unplug
the appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front of the
washing machine (see
figure);
2. unscrew the lid
rotating it anti-
clockwise (see figure): a
little water may trickle
out. This is perfectly
normal;
3. clean the interior thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If
you see any cracks, replace it immediately: during
the wash cycles, water pressure is very strong and
a cracked hose could easily split open.
 Never use hoses that have already been used.

13
GB
Troubleshooting
Your washing machine could fail to work. efore calling for Assistance (see page 14), make sure the problem
can't easily be solved by consulting the following list.
Problem
The machine does not switch
on.
The wash cycle does not start.
The machine does not fill with
wateror "H2O" will flash on the
display.
The machine continuously fills
with water and continually
drains away or Water left in the
drum or tuck on wash.
The machine does not drain or
spinor F05 error code in the
display.
The machine does not heat or
poor wash results.
The programme takes too
longor The Display changes
the estimated 'Time to End'
during the programme.
The machine vibrates a lot
during the spin cycle.
Possible causes/ olution:
 The appliance is not plugged into the socket fully, or not enough to
make contact.
 There is no power to the socket, or the fuse has blown in the mains plug.
 The door is not closed properly.
 The 'ON/OFF' button has not been pressed.
 The 'START/RESET' button has not been pressed.
 The water tap has not been turned on to allow water to flow into the machine.
 A delayed start has been set.
 The water inlet hose is kinked.
 The water inlet hose is not connected to the water supply.
 The water pressure is too low.
 The water tap has not been turned on to allow water to flow into the machine.
 There is no water supply to the house.
 The inlet valve filter is blocked.
 The 'START/RESET' button has not been pressed.
 The top of the drain hose is too low - It must be fitted at a height
between 65 and 100 cm from the floor.
 The drain hose is connected incorrectly to the sink trap allowing water to
run into the machine, the drain hose must be positioned higher than the
bottom of the sink to prevent water flowing down the drain hose.
 The end of the drain hose has been pushed too far down the
standpipe, the 'U' bracket should be fitted 100 mm from the end of
the drain hose.
 The Pump filter is blocked.
 The Easy iron function is enabled: to complete the programme,
press the START/RESET button (see page 11).
 The drain hose is kinked.
 New Installation - The blanking cap or spigot has not been removed
if connected under a sink.
 The drain hose or sink trap is blocked.
 The wash cycle does not include draining, some wash cycles require
the drain phase to be started manually.
 The 'Spin Speed' is in the OFF position.
 The 'Temperature' is in the OFF position.
 Programme times will vary due to water pressure, the incoming water
temperature and if the wash load goes out of balance. This will
increase the programme times accordingly (see ' The machine wont
spin properly' below).
 The feet have not been adjusted, enabling the machine to rock.
 New Installation - Either the Transit olts including the plastic
spacers, or the Polystyrene Packaging have not been removed when
installing the machine.
 The machine is trapped between cabinets and/or walls.
 The load is in a slight out of balance condition and machine is
spinning, but at a lower speed.

14
GB
The machine is noisy.
The machine wont spin
properly.
The machine leaks from the
dispenser.
The machine leaks (other than
dispenser).
The indicator lights on the
console are flashing rapidly.
The machine smells.
The machine door cannot be
opened.
Door eal damaged at the
bottom.
The water level is too low when
the machine is washing.
There is too much foam.
After completing the
programme, or before starting
a programme, the machine has
turned itself off (no lights).
General.
 There will always be some motor, pump and drum noise during spin.
 Out of alance detected when attempting to go into a spin cycle - If this
happens the machine will continue to try to repeat the distribution of the load
required before the machine will go into higher spin speeds - This will increase
the programme time accordingly. This is a safety feature to prevent damage.
Out of alance can be caused by washing a single heavy item (eg duvet,
quilt, etc). - Try the programme again using a different load.
 The dispenser drawer is blocked with detergent and requires cleaning.
 The water pressure is too high and requires turning down - turn down
the tap on the water supply pipe slightly and try again.
 The machine is tilting forwards - It must be level when in its final position.
 The fill hose is loose, check both the cabinet and tap ends.
 The fill hose is tight but still leaks, if so replace the rubber washers, or
the fill hose is missing the rubber washer.
 The drain hose is not fixed in properly.
 Switch off the machine and unplug it, wait for approximately 1 minute
and then switch it back on again If the problem persists contact the
Technical Assistance Service.
 The machine requires a service wash. Run a 90 degree wash cycle with
detergent and no laundry.
 The door will not open until the door lock indicator light goes out
shortly after the program has finished.
 The door seal has drainage holes at the bottom - This is normal.
 The water level is correct if it can be seen at the bottom of the door.
 The detergent is not suitable for machine washing (it should display the
text 'for washing machines' or 'hand and machine wash' or the like).
 To comply with new energy saving regulations the machine is fitted
with an automatic standby system. Press 'ON/OFF' button for 3
seconds to activate the machine, it can then either be switched off or
a new programme selected.
 Your washing machine contains sensors that monitor progress during
the wash cycle (eg: Water Levels, Temperatures, Out of alance
loads, Wash time/progress). Normally, if your machine successfully
completes the cycle, there is unlikely to be anything wrong!
Remember, you will be charged for a service call for problems caused by incorrect installation,
as listed above.
Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.
Do not wash items which do not have a wash label, or wash items that are not intended as
machine washable.

15
GB
Assistance
12 Months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturers guarantee, which covers the cost of breakdown repairs for
twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either
workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.
This guarantee is subject to the following conditions:
-The appliance has been installed and operated correctly and in accordance with our operating and
maintenance instructions.
-The appliance is used only on the electricity or gas supply printed on the rating plate.
-The appliance has been used for normal domestic purposes only.
-The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any
person not authorised by us.
-Any repair work must be undertaken by us or our appointed agent.
-Any parts removed during repair work or any appliance that is replaced become our property.
-The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
-Damage resulting from transportation, improper use, neglect or interference or as a result of improper
installation.
-Replacement of any consumable item or accessory . These include but are not limited to:
plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
-Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS EEN USED IN COMMERCIAL OR
NON-DOMESTIC PREMISES.
5 Year Parts Guarantee
Indesit also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you registering your
appliance with us and the parts being fitted by one of our authorised engineers. There will be a charge for our
engineer's time. To activate the extra parts warranty on your appliance, simply call our registration line on 08448 24
24 24 (Republic of Ireland 01 230 0800).
Extended Guarantees
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair bills
for the life of your policy. To find the ideal plan for you please call our advice line on
08448 226 226 (Republic of Ireland 01 230 0233).
Free Helpdesk ervice
We have a dedicated team who can provide free advice and assistance with your appliance if you experience any
technical difficulties within the first 90 days of ownership. Simply call our Indesit Service Hotline on 08448 224 224
(Republic of Ireland 0818 313 413)for telephone assistance, or, where necessary, to arrange for an engineer to call.

16
GB
195064819.02
05/2010 - Xero Fabriano
After ales ervice
No one is better placed to care for your Indesit appliance during the course of its working life than us - the manufacturer.
Essential Contact Information
Indesit ervice
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1100 fully qualified
engineers on call to ensure you receive fast, reliable, local service.
UK: 08448 224 224
Republic of Ireland: 0818 313 413
www.indesitservice.co.uk
Please note: Our advisors will require the following information:
Model number:
erial number:
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically clean
your appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
www.indesitservice.co.uk
Appliance Registration
We want to give you additional benefits of Indesit ownership. To activate your free 5 year parts guarantee you must
register your appliance with us.
UK: 08448 24 24 24
Republic of Ireland: 01 230 0800
www.indesitservice.co.uk
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate, Dublin 17
Recycling & Disposal Information
As part of Indesit's continued commitment to helping the environment, Indesit reserves the right to use quality, recycled
components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the door, plug
and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure that the appliance can
no longer be plugged into a mains socket, and the door cannot be locked shut.