Indesit WM 12 X User manual

Washing machine
Instructions for installation and use
WM 12 X

Herearethe12topicsexplainedinthismanual.Read,learnand
have fun: you will discover many secret ways to get a better
wash,moreeasilyandmakingyourwashingmachinelastlonger.
Quick guide
1. Installation and removal (p. 10)
Installation,afterdeliveryortransport,isthemostimportantoperation
forthecorrectfunctioningofyourwashingmachine.Alwayscheck:
1. Thattheelectric system conforms to regulations;
2. Thattheinletand drainingpipes are connected correctly.
Never use pipes that have already been used;
3. Thatthewashingmachineislevelledproperly;something
worth checking to aid the performance of your
washingmachine;
4. That the drum's fixing screws have been removed from
the back of the washing machine.
2. What goes in your washing machine and how
to start it (p. 2)
A correct distribution of your laundry is vital to the successful
outcomeofthewashandthelifeofthewashingmachine.Learnall
the tips and secrets to dividing your linen:colour, type of fabric.
3. Guide to understanding labels (p. 5)
Thesymbolsonthelabelsofyour garments areeasytounderstand
and equally important for the success of your wash.The guide
includessimple instructions to help youchoose the right tempera-
ture, wash cycles and ironing methods.
4. Useful tips to avoid mistakes (p. 6)
Years back, our grandmothers were the ones who gave us good
advice - and in those days synthetic fibres did not exist: washing
was easy.Today, your washing machine offers you helpful advice
allowing you to wash wool even better than an expert laundress
would by hand.
5. The detergent dispenser (p. 7)
Howtousethedetergentdispenser and the bleachcompartment.
6. Understanding the control panel (p. 3)
Washing machine’s control panel is very simple.It has only a few
essential buttons to help you choose any type of wash cycle,
rangingfromthemostenergetic,capableofcleaningamechanic’s
overalls,tothe most delicate forwool.Familiarisingyourselfwithit
will help you get the best out of your wash while helping your
washing machine last longer.It’s easy.
7. Guide to the wash programmes (p. 4)
Herein is an easy table to help you choose the right programme,
temperature,detergents and possible additives. Choose the right
programme and you will get better results with your wash while
saving time, water and energy, day after day.
8. Care and maintenance (p. 14)
With just a bit of care, it will repay you with loyalty and devotion.
With the necessary upkeep, it will wash for years and years to
come.
9. Problems and solutions (p. 8 and 9)
Beforecallingatechnician,readthesepages: immediate solutions
may be found for a number of problems. If the problem persists,
call your local Indesit customer services who will be pleased to
help.Any failure will be repaired, as soon as possible.
10. Technical characteristics (p. 9)
Hereinare the technical featuresof your washing machine: model
type number, electric and water specifications, size, capacity,
speedof the spin cycle and compliance withItalian and European
regulations.
11. Safety for you and your family (p. 15)
Here you will find the necessary safety guidelines, and it is
important for you to read this section carefully.
12. Indesit stays with you after your purchase (p. 16)
Indesitsupports its productsafter their purchase byofferingyoua
range of special services, professional assistance, spare parts
and quality accessories.
1 Instructions for installation and use

Whatgoesinyourwasher?
Before washing,you cando agreat dealto ensurebetter results.Divideyour garments
according to fabric and colour. Read the labels, follow their guidelines.
Beforewashing.
Divide your washing according
to the type of fabric and colour
fastness.
Emptyallpockets(coins,paper,
moneyand small obejects) and
ensure all loose buttons are
repaired or removed prior to
loading.
How to eliminate the most common stains
Ink and biro Dab with a wad of cotton soaked in methyl alcohol or alcohol at 90°.
Tar Dab with fresh butter, rub in turpentine then wash immediately.
Wax Scrape away, then run a hot iron between two sheets of absorbent paper. Then rub in cotton with turpentine or
methyl alcohol.
Chewing gum Rub in nail polish remover and wipe with a clean rag.
Mold Cotton and white linen should be placed in a solution of 5 parts water, one bleach and a spoon of vinegar, then
washed immediately. For other white fabrics, use hydrogen peroxide at 10 volumes and wash immediately.
Lipstick Dab with ether on wool or cotton. Use tricloroetilene for silk.
Nail polish Place a sheet of absorbent paper on the side of the stain, wet it with nail polish remover, shifting the
garment as the sheet gradually changes colour.
Grass Dab with a wad of cotton soaked in methyl alcohol.
Starting the washer
Starting your washing machine
in the right way is important for
thequalityof your wash, to help
prevent future problems and
enhancelifeexpectancyofyour
appliance. Once you have
loaded your washing machine
and added the detergent
together with any fabric
conditioner, always check that:
1.The door is closed correctly.
2. The plug is secured in the
socket.
3. The water supply is turned
on.
4.Selectorknob Ais positioned
on one of the symbols (Stop/
Reset).
Choosethedesiredprogramme
The programme is selected
accordingtothetypeofgarments
thatneedtobewashed.Tochoose
aprogramme,refertothetableon
page 4. Turn knob Auntil the
selected programme is aligned
with the mark on the knob, turn
knobBtothedesiredtemperatu-
re settings, if necessary use
buttons D, E and F, and lastly,
press on/offbuttonG(Iposition).
Afterinstalling your newwashing machine, starta wash
cycle by setting programme "1" at 90 degrees.
For more delicate
garments:
protect underwear, tights
and stockings and delicate
items by placing them in a
canvaspouch
Dividing your garments
accordingto fabricand
colour, is very important
for good results
Attheendofthewashcycle...
The Ilamp to extinguish: it will
takeabout three minutes.
Thenturnthewashing machine
off by pressing on-off button G
(Oposition).You can now open
the washing machine door
safely.Afterhavingremovedthe
freshly cleaned washing, leave
the door open to allow air
circulationinside the drum.
Alwaysdisconnect electricity at
thesocketandturnoffthewater
supply.
Remember that, in the event
of a power failure, or should
the washing machine switch
itself off, the programme
chosen will remain in its
memory.
The labels say it all.
Always look at the labels: they
tell you everything about your
garment and how to wash it in
the best possible way.
The table on page 5 shows all
meanings behind these
symbols. Their recom-
mendations are important to
achieve better wash results.
Instructions for installation and use 2
M
Bigand small happily
together.
This washing machine has a
specialelectroniccontroldevice
for even distribution: before the
spin cycle starts, this device
allowsthegarmentstopositions
themselves, to minimise noise
and vibrations during the spin
cycle.

D
A
B
C
EFGHI
Press this button in
programmes5-6-7-9-10 andthe
wash cycle will come to a stop
onsymbol .Youcancomple-
teit by pressing button Dagain.
Important: thisfunctionshould
notbeusedwhenbuttonF(Stain
removal)hasbeen pressed.
Slow spin
Use this button to reduce the
spinning speed from 1200 to
600rpmforthecotton and linen
programmes and from 850 to
600 rpm for the synthetic
fabrics programmes.
Stain removal (see page 7)
Thanks to this command, the
washing machine will carry out
a more intensive wash that
optimisesthe effectivenessofthe
liquid additives, thus allowing
more resistant stains to be
removed. When you press the
stainremovalbutton,youcannot
activatethepre-wash.
On-off
When button G is pressed, the
washing machine is switched
on, when it is not the machine
is switched off.
Turning the appliance off
does not cancel the selected
programme.
The on-off lamp
Lamp H flashes when the
appliance is switched on and
awaitingaprogrammetobeset.
A steady light means the
appliance has accepted the
selectedprogramme.
Here I’m in command
Understandingthecontrolpanel
Making the right choice is important. And it’s easy.
Programme selector knob
Usethisknobtoselectthewash
programme.
Turn this knob clockwise only.
To select a programme, you
should turn the knob so that the
symbol/number of the desired
programme is in line with the
pointerontheknob.
Now press on/off button G
(positionI),pilotlamp Hwillstart
flashing.
After 5", the setting will be
accepted, pilot lamp Hwill stop
flashing(stayinglit)andthewash
cyclewillbegin.
Should you wish to interrupt the
programme in progress or set a
new one, select one of the
symbols (Stop/Reset)andwait
5" : when the cancellation has
been accepted, pilot lamp H
flashes,andyoucanthenturnthe
applianceoff.
Afterthewashcyclehasbeenset
and accepted by the washing
machine, turning the knob will
have no effect (except for when
it is on position Stop/Reset).
Temperature control knob
Itisusedtosetthewashtempe-
rature in the recommended
programmetableonpag.4.Italso
allows you to reduce the tempe-
rature recommended for the
selectedprogramme,andevento
set a cold wash cycle ( ).
Detergent dispenser
It is divided into three
compartments:
1.Detergent for pre-wash;
2.Detergent for the main cycle
wash;
3.Fabric conditioner.
The washing machine is
equipped with an extra
compartment 4(providedasan
accessory)for the bleach, to be
inserted in compartment 1.
Easyiron
This function allows your
washing to come out of the
machine without creases,
making it much easier to iron.
Youcanuseitwithprogrammes
3-4 (Cotton), 5-6-7(Synthetics)
and9-10 (Delicates).
The detergent dispenser with the
additional bleach compartment
is here.
3 Instructions for installation and use
The door block lamp
Thesafetylampindicatesthatthe
washingmachinedoorislocked
to prevent it from being opened
accidentally. To avoid any
damages to lock mechanism,
you must wait for the lamp to
extinguish, before attempting to
openthedoorwhichtakesaround
threeminutes.
MAX
12
4
3

Type of fabric and degree of soil Programme
knob Temperature knob Detergent for wash Fabric softener Stain rem. button/
Bleach
Length of
the cycle
(minutes)
Description of wash cycle
COTTON
Exceptionally soiled whites
(sheets, tablecloths, etc.) 1 90°C ◆◆ 165 Warm prewash, wash cycle at 90°C, rinse
cycles, intermediate and final spin cycles
Exceptionally soiled whites
(sheets, tablecloths, etc.) 2 90°C ◆◆
Del./Trad. 145 Wash cycle at 90°C, rinse cycles,
intermediate and final spin cycles
Heavily soiled whites and fast colours 3 60°C ◆◆
Del./Trad. 130 Wash cycle at 60°C, rinse cycles,
intermediate and final spin cycles
Slightly soiled whites and delicate
colours (shirts, jumpers, etc.) 4 40°C ◆◆
Del./Trad. 95 Wash cycle at 40°C, rinse cycles,
intermediate and final spin cycles
Rinse cycles/Bleach ◆Del./Trad. Rinse cycles, intermediate and final
spin cycles
Spin cycle Draining and final spin cycle
Stop/Reset Interrupts/Cancels the selected programme
SYNTHETICS
Heavily soiled fast colour synthetics
(baby linen, etc.) 5 60°C ◆◆
Delicate 100 Wash cycle at 60°C, rinse cycles,
anti-crease or delicate spin cycle
Heavily soiled fast colour synthetics
(baby linen, etc.) 6 50°C ◆◆
Delicate 95 Wash cycle at 50°C, rinse cycles,
anti-crease or delicate spin cycle
Delicate colour synthetics
(all types of slightly soiled garments) 7 40°C ◆◆
Delicate 70 Wash cycle at 40°C, rinse cycles,
anti-crease or delicate spin cycle
Delicate colour synthetics
(all types of slightly soiled garments)8 30°C ◆◆ 30 Wash cycle at 30°C, rinse cycles and
delicate spin cycle
Rinse cycles/Bleach ◆Delicate Rinse cycles, anti-crease or delicate
spin cycel
Fabric softener ◆Rinse cycles with automatic introduction of
softener, anti-crease or delicate spin cycle
Spin cycle Draining and delicate spin cycle
Stop/Reset Interrupts/Cancels the selected programme
DELICATES
Wool, hand wash 9 40°C ◆◆ 60 Wash cycle at 40°C, rinse cycles and
delicate spin cycle
Particularly delicate garments and
fabrics (curtains, silk, viscose, etc.) 10 30°C ◆◆ 50 Wash cycle at 30°C, rinse cycles,
anti-crease or draining
Rinse cycles ◆Rinse cyclesi, anti-crease or draining
Spin cycle Draining and delicate spin cycle
Drain Drain
Stop/Reset Interrupts/Cancels the selected programme
A programme for all seasons
What are you washing today?
Instructions for installation and use 4
Daily wash Your washer has a programme available for the washing of lightly soiled garments in a short amount of time.
By setting programme 8 at a temperature of 30°C, you can wash different types of fabrics together (except for wool and silk), with a
maximum load of 3kg. This programmes allows you to save on both time and energy as it only lasts around 30 minutes.
WE RECOMMEND THE USE LIQUID DETERGENT.
Important: to cancel the wash programme you have just set, select one of the symbols (Stop/Reset) and wait for at least 5 seconds.
Special programme
The data found in the table is purely indicative, and can vary according to the quantity and type of washing, the water system temperature and
the room temperature.

Wash Bleaching Ironing Dry cleaning Drying
Strong
action
Delicate
action
High
Temp.
Low
Temperat.
Wash at
95°C Bleaching only in cold water Hot iron at max 200°C Dry clean with any solvent Machine dryable
Wash at
60°C Do not bleach
Medium hot
ironing at
max 150°C
Dry clean only with
perchloride, benzine
av., pure alcohol,
R111 and R113 Do not machine dry
Wash at
40°C Iron at max 110°C
Dry clean with av.
benzine, pure alcohol
and R113 Spread to dry
Wash at
30°C Not ironable Do not dry clean
Hang to dry
without spin
drying
Hand wash Dry on clothes hanger
Not
washable in
water
Understanding labels
Learnthe meaning of these symbolsand youwill get better
results, your garments will last longer resulting in an
improvedwash.
AlloverEurope,garment labels
containmessagesexpressedin
small yet important symbols.
Understanding them is very
important if you want to get
better results and treat your
garmentstheway they deserve
tobe treated.
These symbols are divided in
five different categories and
shapes:
washing , bleaching ,
ironing ,dry cleaning and
drying .
Consult and learn the symbols in this table: they will help you
obtain a better wash, treat your clothes properly, and get a
better performance out of your washing machine.
Useful tips
Turn shirts inside out to get better results
and make them last longer.
Always empty pockets of their contents.
Look at the label: it will always give you useful
advice.
When loading your washing, try to have a mixture
of large to small items. Make sure you select the right
temperature!
5 Instructions for installation and use
l
c
A
P
F

Usefultips
Never use your washing
machinetowash...torn,fraying
or non-hemmed linen. If it is
absolutelyneccessary,placeitin
abagforprotection.Donotwash
colouredlinenwithwhites.
Watchtheweight!
For best results, do not exceed
the weight limits stated below
(figures show weight of dry
garments):
- Resistant fabrics:
5,5 kg maximum
- Synthetic fabrics:
2.5 kg maximum
- Delicate fabrics:
2 kg maximum
- Pure new wool:
1 kg maximum
Howto wash almost anything
Curtains.
Curtains tend to crease a great
deal. A useful tip to reduce
creasing: fold the curtains and
place them in a pillow case or
meshbag.Donotloadanything
else inside the appliance, this
will ensure that the overall
weightdoesnotexceedthe half
load. Remember to use the
specific programme 10 which
automaticallyexcludes the spin
cycle.
Trainers.
Once you have removed mud
and dirt from trainers, you can
even wash them with jeans or
any other tough garments. Do
not wash trainers with whites.
Quilted coats and anorak.
You can washquilted coats and
wind-cheaters, too, if they are
padded with goose or duck
down. Do not load more than
2-3 kg and never load 5,5 kg.
Repeat rinse once or twice
usingthe gentle spin.
How much does it weigh?
1sheet400-500gr.
1pillowcase150-200 gr.
1tablecloth400-500gr.
1bathrobe900-1,200gr.
1towel150-250gr.
Coloured T-shirts, printed
ones and shirts last longer if
turnedinsideoutbeforewashing.
Printed T-shirts and sweatshirts
shouldalwaysbeironedinsideout.
Dungaree alert.
Very popular “salopette” type
overalls have straps with hooks
thatcandamagethedrumofyour
washing machine or other
garments during the wash. To
minimisetherisk,placehooks in
thepocketandfastenwithsafety
pins.
Holidays: unplug the
appliance.
It is recommended that you
shouldunplugthemachinefrom
thesocketand turn off the water
supply. Leave the door ajar to
allow air circulation to the draw
andthedoorgasketarea.Thiswill
preventunpleasantodours.
Instructions for installation and use 6
For best results, we
recommend you use a
specific detergent, taking
carenottowashmore than
1kg of laundry.
WOOLCYCLE

You must follow the dosage
recommendations provided by
themanufacturerswhenadding
detergent or fabric conditioner.
Doseswillvaryaccording to the
wash load, the water hardness
andhowsoiledthe washing is.
Experience will help you select
the right dosage almost
automatically:itwillbecomeyour
secret.
Beforeaddingdetergentforpre-
washing in compartment 1,
make sure that the extra
compartment for bleach 4has
notbeeninserted.
Ensure no overfilling when
adding fabric conditioner in
compartment 3.
The washing machine automa-
tically adds the softener to the
washineachprogramme.
Liquid detergent is poured into
compartment 2just a few
seconds before starting the
wash cycle.
Incompartment 1:
Detergentfor pre-washing(powder)
Incompartment 2:
Detergentfor washing
(powder or liquid)
Incompartment 3:
Additives(softeners,perfumes,etc.)
Incompartment4:
Bleach and delicate bleach.
Usefultipsabout thedetergentdispenser
It’s important for a good wash
The first secret is the easiest: the detergent dispenser is
opened by rotating it outwards.
Rememberthatliquiddetergent
is only designed for wash
cycles of up to 60 degrees on
non pre-wash items.
Specialcontainersaresoldwith
liquid or powder detergents for
placing inside the washing
machine drum, these are
positioned according to the
instructions found in the
detergentbox
Never use hand wash
detergent,because it may form
too much foam, which could
damagethewashing machine.
Detergentsthat are specifically
formulated for both hand and
machine wash are an
exception.
One last secret: when washing
with cold water, always reduce
theamountofdetergentyouuse:
it dissolves less easily in cold
water than in hot water, so part
of it would be wasted.
Cuttingcostsefficiently A guide to environmentally
friendly and economic use
of your appliance.
MAXIMISETHELOADSIZE
Achieve the best use of energy, water, detergent and time by using the recommended
maximum load size.
SAVE up to 50% energy by washing a full load instead of 2 half loads.
DO YOU NEED TO PRE-WASH?
For heavily soiled laundry only!
SAVE detergent, time, water and between 5 to 15% energy consumption by NOT
selecting Prewash for slight to normally soiled laundry.
ISA HOT WASH REQUIRED?
Pretreat stains with stain remover or soak dried in stains in water before washing to
reduce the necessity of a hot wash programme.
SAVE up to 50% energy by using a 60°C wash programme.
BEFORE USING A DRYING PROGRAMME ...
SAVE energy and time by selecting the highest suitable spin speed to reduce the water
content in laundry before using a drying programme.
The detergent dispenser can be
removed and cleaned: pull it outwards,
as indicated in the figure.Then leave it
under running water for a few minutes.
7 Instructions for installation and use
Bleach cycle and stain remover
button
If bleaching is necessary, the
extracase 4(provided) must be
inserted into compartment 1of
thedetergentdispenser.
When pouring in the bleach,be
carefulnottoexceedthe "max"
level indicated on the central
pivot (see illustration).
Theuseoftheadditionalbleach
container excludes the
possibilityofusingthepre-wash
cycle. Traditional bleach can
only be used on sturdy white
fabrics, whereas delicate
bleach can be used for
coloured fabrics, synthetics
and for wool.
You cannot bleach with the
“Silk” programme and with the
“special programmes” (see
page4).
Use the stain removal button
every time you want to bleach.
Should you want to do it
separately you must pour the
bleach into the additional
container 4, press button F
(stain removal), start the
washing machine, then select
one of the symbols
according to the type of fabric.
When you bleach during a
normal wash cycle, pour the
detergent and any additives in
the special compartments,
press button F (stain removal),
set the programme you desire
and turn the washing machine
on.
MAX
12
4
3
1
2
MAX
MAX

Thewashingmachine
fails to fill with water.
Is the hose correctly
connected to the tap?
Is there a water shortage ?
There could be work in
progress in your building or
street.
Is there sufficient water
pressure? The autoclave
maybe malfunctioning.
Is the tap filter clean? If the
water is very calcareous, or
if work has recently been
carried out on the water
piping, the tap filter could be
clogged with particles and
debris.
Is the rubber hose kinked?
The tract of the rubber hose
bringing water to washing
machine must be as straight
as possible. Make sure it is
not squashed or kinked.
Theprogramme selector
knobkeeps turning?
Wait a few minutes for the
drain pump to empty the
tub, switch the washer off,
select one of the symbols
stop/reset , then switch it
backon.Iftheknobcontinues
to turn, call for assistance
because it is showing an
anomaly.
Thewashingmachine
continuouslyfills and
drainswater.
Isthedrainhosepositioned
too low? It must be installed
ata height ranging from60 to
100cm.
Is the end of the hose
immersed in water?
Does the wall drainage
system have a breather
pipe? If the problem persists
even after these checks, turn
the water supply off the
machine and call for
assistance.
Ifyoulive on an upper floorof
your building, there may be a
problemwithyourdraintrap.
To solve this problem, a
special valve must be
installed.
Before calling,read the following
Troubleshooting
In most cases, when your washing machine fails to work, the problems arising
can be easily solved without having to call for a technician. Before calling for
assistance, always check these points.
Thewashingmachine
fails to start.
Istheplug correctlyinserted
intothesocket?Itcouldhave
beenmovedwhilstcleaning.
Is there electricity in the
house?
A circuit breaker may have
switched off as a result of too
many electrical appliances
working at the same time. Or
maybeduetoa generalfailure
inyourentirearea.
Is the washing machine
doorclosedproperly?
For safety reasons, the
washingmachinecannotwork
if the door is open or not shut
properly.
Is the On/Off button
pressed?
Ifitis,thenaprogrammedstart
hasbeenset.
Is the programmed start
knob,inthecorrect position
for those models
concerned?
Is the water supply turned
on? For safety reasons, if the
washing machine does not
load water, it cannot start a
wash cycle.
RIGHT WRONG
Turn off the water
supply after use.
This will eliminate
the possibility of
leakage.
Always leave the
appliance door ajar
to avoid bad odours.
Clean the
appliance’s
exteriors gently.
To clean the
exteriors and the
rubber parts of the
appliance, always
use a soft cloth
dipped in warm and
soapy water.
Leave the washing
machine plugged in while
cleaning.
Even during maintenance,
the appliance should
always be unplugged.
Use solvents and
aggressive abrasives.
Never use solvents or
abrasives to clean the
external and rubber parts
of the washing machine.
Neglect the detergent
dispenser.
It is removable and can
easily be cleaned by
leaving it under running
water.
Go on holiday without
thinking about her.
Before leaving, always
make sure that the
washing machine is
unplugged and that the
water supply is turned off.
Instructions for installation and us e 8
Simple: with the new Indesit technology, you need less than
half of it, to get good results on twice as much!
This is why you cannot see the water through the door:
because there is little, very little of it, to respect the
environment yet without renouncing maximum cleanliness.
And, on top of that, you are also saving electricity.
But where did all the water go?

Model WM 12 X
Dimensions width 59,5 cm
height 82 cm
depth 53,7 cm
Capacity from 1 to 5,5 kg
Electrical
connections voltage 230/240 Volt 50 Hz
maximum absorbed power 2050 W
Water connections maximum pressure 1 MPa (10 bar)
minimum pressure 0,05 MPa (0,5 bar)
drum capacity 46 litre
Spinning speed up to 1200 rpm
Control programs in
compliance with
IEC regulation 456
programme 3; temperature 60°C; carried out with 5 kg load.
This appliance conforms with the following E.E.C. directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications
- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications
Too much foam.
Isthedetergentappropriate
for machine washing?
Check whether the definition
onitslabelreads“formachine
wash” or “hand and machine
wash”, or any other similar
wording.
Is the correct amount being
used? An excessive amount
of detergent, besides
producing too much foam,
does not guarantee a more
effective wash, and causes
scalinginthe internal parts of
theappliance.
If, despite all checks, the
washing machine fails to
function and the problem
persists, call your nearest
authorised Customer Service
Centre, providing the following
information:
- thenature of malfunction
- themodel type no.(Mod.....)
- the serial number (S/N ....)
Thisinformationcanbefoundon
the data plate situated at the
back of the washing machine.
Is there space between the
machine and adjacent
units? If it is not a built-in
model, the washing machine
will oscillate a bit during the
spincycle.A few cm of space
should therefore be left
aroundit.
The washing machine
leaks.
Is the metal ring of the inlet
hose properly attached?
Turn off the water supply,
unplug the appliance and try
tightening its attachment
withoutforcing it.
Is the detergent dispenser
obstructed? Remove and
wash it under tap water.
Is the drain hose well
attached?Turn off the water
supply, unplug the appliance
and try tightening its
attachment.
Is the washing machine’s
drain duct clogged? Isthere
an extension of the drain
hose? If so, is it positioned
incorrectly, blocking the
water flow?
Excessive vibration
during the spin cycle.
Havealltransitscrews been
removed durind instal-
lation? See the following
page on installation
procedures.
Has the washing machine
beenlevelledcorrectly?The
levelling of the appliance
should be checked
periodically. Adjust the feet
and check them with a level.
The washing machine
does not drain or spin.
Does the selected
programme incorporates
water draining? Some
programmes stop at the end
of the wash cycles and
draining will have to be
selected manually.
Is the“Easy iron" function
-where provided - enabled?
Thisfunctionrequiresmanual
selectionfor draining.
Is the drain hose kinked?
The tract of the drain hose
must be as straight as
possible.Makesurethedrain
hose is not squashed or
kinked.
Technical characteristics
Alwaysget
assistancefrom
authorised
techniciansand
always insist on
original spare parts.
9 Instructions for installation and use

Instructions for installation and use 10
When the new
washer arrives
Installationand removal
Whether new or just transported to a new house,
installation is extremely important for the correct
functioning of your washing machine.
Connecting the drain hose
The drain hose (hooked pipe) is
securedtotherearofthemachine
by support clips and may be
routedtorightorleftasrequired.
The hook to be used in case the drain
hose ends at a height below 60 cm.
Thedrainhoseshouldbeplaced
in a stand pipe with a minimum
internal diameter of 38 mm (1½
inches)oritcanbepositionedover
a sink or it can be connected as
shown in Fig. A. The height of
stand pipe or sink should be
between 60 and 100 cm (24 and
40 inches). Care must be taken
that the hose is not obstructed,
twisted, submerged or kinked. If
the hose is connected with an
airtightjoining,provisionshouldbe
madetopreventsyphoning.
The guide for draining into tubs and
sinks.
Fig. A
Electric connection
Your appliance is now supplied
with a 13 amp fused plug it can
bepluggedintoa13 ampsocket
for immediate use. Before using
the appliance please read the
instructionsbelow.
WARNING - THIS APPLIANCE
MUST BE EARTHED.
THE FOLLOWING OPERATIONS
SHOULD BE CARRIED OUT BY A
QUALIFIEDELECTRICIAN.
Replacingthefuse:
When replacing a faulty fuse, a
13 amp ASTA approved fuse to
BS1362shouldalwaysbeused,
andthefusecoverre-fitted.Ifthe
fuse cover is lost, the plug must
not be used until a replacement
isobtained.
Replacementfusecovers:
If a replacement fuse cover is
fitted, it must be of the correct
colour as indicated by the
coloured marking or the colour
thatisembossedinwordsonthe
baseoftheplug.Replacements
can be obtained directly from
yournearest Service Depot.
Afterremovingtheappliancefrom
its packaging, check that it is
intact. If in doubt, contact a
qualifiedtechnicianimmediately.
The inside of the machine is
supported,fortransportation,by
fourscrewsonthebackpanel.
Before using the washing
machine, remove the screws,
removethespacerstogetherwith
therubbertubesattachedtothem
(keepingalltheparts)andusethe
plasticplugsprovidedtofillinthe
holes.
Important:Usethecap(provided)
to close the 3 holes which housed
thestoppin,situatedintheright-hand
part of the lower back of the
washingmachine.
Levelling
The washing machine must be
levelled appropriatey in order to
guaranteeitscorrectfunctioning.To
level the appliance, the front feet
must be adjusted; the angle of
inclination,measuredaccordingto
the worktop, must not exceed 2°.
Whenplacedoncarpet,makesure
theventilationisnotreduced.
The front feet are adjustable.
Connection to the water
mains
Both hot and cold water supplies
arepreferableandtheyshouldbe
between 34.5kN/m²(5lb/in²) and
1034.2kN/m²(150lb/in²)pressure.
Thehosehavingtheredendfitting
should be encountered between
the hot supply and the threaded
connectionadjacenttotheletterH
on the rear of the machine. The
hosehavingthewhiteendfittings
shouldbeconnectedbetweenthe
cold supply and the threaded
connectionadjacenttotheletterC
on the rear of the machine.
Remember to insert a sealing
washer at each connection to
ensure watertight joints. Do not
overtighten the connections by
usingtools-handtight issufficient
topreventleaks.Itisgenerallymore
convenienttohavethesesupplies
away from the sink taps. Where
no suitable hot water supply is
availableoritdoesnotmeetthese
requirements,bothinlethosesmay
be connected to a cold supply by
using two taps etc., or a «T»
junctionontheplumbinghowever,
useofcoldwateronlywillincrease
programmetimes.
Note: the maximum temperature
shouldnotexceed70°C(158°F).
The rubber gasket.
Connect the inlet hose to the
threaded connector on the
machinerear.
Water pipe inlet at the top right.
Warning!
The company denies all
liability if and when these
norms are not respected.
Plastic bags, expanded
styrofoam, nails and other
packaging parts are not
children’s toys, and are
potentially dangerous.
Retain the transit screws,
spacers and washers.
Should you move house
then these should be
replaced to support the
inside of the machine to
prevent damage when
transporting the machine.

11 Instructions for installation and use
Removing the plug:
If your appliance has a non-
rewireablemouldedplugandyou
shouldwishtore-routethemains
cable through partitions, units
etc.,pleaseensurethateither:
the plug is replaced by a fused
13 ampere re-wearable plug
bearingtheBSImarkofapproval.
or:
themainscableiswireddirectly
into a 13 amp cable outlet,
controlled by a switch, (in
compliancewithBS5733)which
isaccessiblewithoutmovingthe
appliance.
Disposing of the plug:
Ensure that before disposing of
theplugitself,you makethepins
unusable so that it cannot be
accidentally inserted into a
socket.
Instructions for connecting
cable to an alternative plug:
Important: the wires in the
mains lead are coloured in
accordance with the following
code:
Green &Yellow Earth
Blue Neutral
Brown Live
As the colours of the wires in the
leadmaynotcorrespondwiththe
colouredmarkingsidentifyngthe
terminalsinyourplug,proceedas
follows:
Connect Green & Yellow wire to
terminal marked Eor or
colouredGreenorGreen&Yellow.
Connect Brown wire to terminal
markedLorcolouredRed.
Connect Blue wire to terminal
marked Norcoloured Black.
Ifa13ampplug(BS1363)isused
itmustbe fittedwitha
13amp fuse, either in theplug or
adaptororatthedistributionboard.
If you are in any doubt the
electricalsupplytoyourmachine,
consult a qualified electrician
beforeuse.
How to connect an alternati-
ve plug:
Thewiresin this mains lead are
colouredinaccordancewiththe
followingcode:
BLUE NEUTRAL(N)
BROWN LIVE(L)
GREEN&YELLOW EARTH(E)
Disposing of the appliance:
Whendisposingoftheappliance
please remove the plug by
cuttingthemainscableasclose
aspossibletotheplugbodyand
disposeofitasdescribedabove.
GREEN &
YELLOW
BROWN
BLUE
13 ampere fuse
CROSS-BAR
CORD GRIP

Mounting the wooden panel
onto the door and inserting
the machine into cabinets:
In the case where the machine
must be shipped for final
installation after the wooden
panel has been mounted, we
suggest leaving it in its original
packaging.The packaging was
designed tomake it possible to
mount the wooden panel onto
themachinewithoutremovingit
completely (see figures
below).
The wooden panel that covers
thefaceofthe machinemustnot
be less than 18 mm in
thicknessandcanbehingedon
either the right or left. For the
sake of practicality when using
the machine, we recommend
that the panel be hinged on the
same side as the door for the
machine itself - the left.
Door Mounting Accessories
(Fig.1-2-3-4-5)
- No. 6 type Aself-threading
screws, l =13 mm.
- No. 2 type Bmetric,
countersunk screws, l =25; for
fasteningthemagnetplatetothe
cabinet.
- No. 4 type Cmetric screws,
l=15mm; formountingthehinge
supports to the cabinet.
- No. 4 type Dmetric screws,
l=7mm;formountingthehinges
on the supports.
Fig. 1 Fig. 2
Fig. 3 Fig. 4
Fig. 5
N° 2 Hinges
N° 1 Magnet N° 1 Magnet plate
N° 1 Rubber plug
N° 2 Hinge Supports
Instructionsforthefitter
AB
CD
E
1
2
3
4
5
6
lavabiancheria
washing machine
machine laver
waschmaschine
Lato porta
Door side
Cote porte
Tur seite
1
2
3
4
5
6
lavabiancheria
washing machine
machine laver
waschmaschine
Latoporta
Door side
Cote porte
Turseite
Fig. 4/B
N° 1 Spacer
Instructions for installation and use 12

Mounting the Parts onto the
Face of the Machine
-Mountthehingesupportsonto
the face of the machine,
positioningtheholeindicatedby
the arrow in fig. 1 towards the
inside of the face and using the
type Cscrews.
- Mount the magnetic plate on
the opposite side, at the top,
using the two type Bscrews.
- Place the spacer illustrated in
fig. 4/B between the appliance
frontand the magnetreceiver.
Using the DrillingTemplate
- To trace the positions of the
holesontheleft-handside ofthe
panel,alignthedrillingtemplate
to the top left side of the panel
using the lines traced on the
extremities as a reference.
- To trace the positions of the
holes on the right-hand side of
the panel, align the drilling
template to the top right side of
thepanel.
- Use an appropriately sized
routertomilltheholesforthetwo
hinges,the rubber plugand the
magnet.
Mounding the Parts onto the
Wooden Panel (Door)
-Insertthehingesintotheholes
(the movable part of the hinge
mustbepositionedfacing away
fromthepanel)andfastenthem
with the 4 type Ascrews.
- Insert the magnet into the top
holeon the oppositeside of the
hingesandfastenitwiththetwo
type Bscrews.
- Insert the rubber plug into the
bottomhole.
The panel is now ready to be
mountedonto the machine.
Mounting the Panel into the
machine
Insert the nib of the hinge
(indicatedby the arrow infig. 2)
into the hole for the hinge and
pushthepaneltowardsthefront
of the machine. Fasten the two
hinges with the type Dscrews.
Fastening the plinth guide
Ifthe machine is installed atthe
endofaset ofmodularcabinets,
mount either one or both of the
guidesfor the base molding (as
shownin fig. 8). Adjust themfor
depth based on the position of
the base molding, and, if
necessary, fasten the base to
theguides (fig. 9).
This is how to assemble the
plinthguide(fig.8):
Fig. 6 Fig. 7 Fig. 9
D
C
C
Adjustingtheappliance height
Theheight of the appliance can
be adjusted (from 820 mm to
835 mm),by turning the4 feet.
Should you require the
appliance to be placed higher
thantheaboveheight,youneed
tousethefollowingaccessories
to raise it to up to 870 mm:
- the two crossbars (G)
- the 4 feet (H)
- the 4 screws (I)
- the 4 nuts (L)
then perform the following
operations(fig.11):
removethe4originalfeet,place
a crossbar Gat the front of the
appliance, fastening it in place
using screws I(screwing them
in where the original feet were)
then insert the new feet H.
Repeat the same operation at
the back of the appliance.
Now adjust feet Hto raise or
lower the appliance from 835
mm to 870 mm.
Once you have reached the
desiredheight, lock nuts Lonto
crossbar G.
Fig. 11
LI
H
G
To adjust the appliance to a
heightbetween870 mmand900
mm,youneed to mount strip M,
adjusting feet Hto the required
height.
Insert the strip as follows:
loosen the three screws N
situated at the front of the Top
cover of the appliance, insert
stripMas shown in fig.12,then
fasten screws N.
Accessories provided for the
height adjustment
Thefollowingcanbefoundinside
thepolystyrenelid(fig.10):
2 crossbars (G),
1 strip (M)
thefollowingcanbe foundinside
theappliancedrum:
4additional feet (H),
4 screws (I),
4 screws (R),
4 nuts (L),
2 plinth guides (Q)
Fasten angle Pusing screw R,
insert plinth guide Qinto the
special slot and once it is in the
desiredposition, lock itin place
using angle Pand screw R.
Insertingthemachineintothe
Cabinet
- Push the machine into the
opening, aligning it with the
cabinets(fig. 6).
-Regulatetheadjustablefeetto
raise the machine to the
appropriateheight.
- To adjust the position of the
wooden panel in both the
vertical and horizontal
directions, use the Cand D
screws, as shown in fig. 7.
Important:closethelowerpart
of the appliance front by
ensuring that the plinth rests
againstthe floor.
Fig. 10
Fig. 12
Fig. 8
M
81 mm
570
min
820
537
595
820 ÷ 900
600 min
13 Instructions for installation and use

Treat your machine well and it will provide
many years of trouble free service
Easy Care and Maintenance
Your washing machine is a reliable companion in life and on the job. It is just as important for you to keep it
in shape.
Your washing machine is
designed to provide reliable
service over many years. A few
simplestepswillhelptoprolong
its life and avoid problems. It is
advisable, to turn off water taps
when the machine is not to be
used, this protects the hoses,
etc.
If the water in your area is too
hard, use a deliming product
(water is hard if it often leaves
whitish stains around taps or
drains,especiallyofbathtubs.
Formoreaccurateinformationas
to the type of water in your
system, call the local water
worksoralocal plumber).
Pockets must always be
emptied removing even pins,
badges and any other hard
object.
The washing machine exterior
should be cleaned with a rag
dipped in lukewarm water and
soap.
Neverexaggeratewithdoses.
Normal detergents already
containdelimingagents. Only if
the water is particularly hard,
that is, rich in lime content, do
we recommend the use of a
specific product at every wash.
A periodical wash cycle with a
dose of a deliming product,
without detergents or washing,
may prove useful.
Never use too much detergent
or additives because this could
cause an excess amount of
foam, scaling and possible
damagetothecomponentparts
of your washing machine.
When in need, check the pump and the rubber hose.
The washer comes equipped with a self-cleaning pump that does not require any cleaning or maintenance.
The water inlet hose
Check the rubber hose at least once a year. If you see any cracks, replace it immediately. When you use your washing
machine, water pressure is very strong and a cracked tube could easily split open.
It is important to wash
the detergent dispenser
regularly.
Toprevent dried washing
powderfrom
accumulating,place the
dispenserunder running
water for a few minutes.
Do not forget to empty all pockets: small objects can
cause damage to your washer.
Instructions for installation and use 14

Your safety and that of
your family
Importantforthesafeuseofyourwashingmachine
Your washer has been built in compliance with
the strictest international safety regulations. To
protect you and all your family.
Read these instructions and all
the information in this manual
carefully:they are an important
source, not only of numerous
useful tips, but also of vital
information on safety, use and
maintenance.
1. themachineshouldnotbe
installed in an outdoor
environment, not even
when a roof shelters the
area,becauseitmay bevery
dangerous to leave it
exposed to rain and
thunderstorms.
2. It must only be used by
adults and exclusively for
washing clothes following
the instructions provided in
thismanual.
3. Shouldithave to be moved,
proceedwiththehelp of two
or three people and handle
it with the utmost care.
Never try to do this alone,
because the appliance is
very heavy.
4. Before loading the washing
machine, make sure the
drum is empty.
5. Never touch the washing
machine when barefoot or
with wet or damp hands
or feet.
6. Never use extensions or
multiple plugs, which are
particularly dangerous in
humid environments. The
power supply cable must
never be bent or
dangerously compressed.
7. Never open the detergent
dispenser while the
appliance is functioning;
do not use hand wash
detergent because the
abundance of foam could
damageits internal parts.
How to change the power supply cable
The washing machine
power supply cable is
specialandcanbepurchased
exclusively from authorised
Technical Service Centres.
To replace the cable:
1.Makesure thatthemachine
isswitchedoffandunplugged.
2. Remove the cover by
unscrewing screws I[fig 13].
3. Disconnect the wires from
the radio interference
suppressor F[fig. 14] noting as
to their position (Blue=N wire;
Brown=L wire) leaving the
earth wire until last .
N.B.: letters L, Nand the
symbol are indicated on the
radio interference suppressor.
4. Remove the screw and
washerV[fig.15],whichactas
astopforthecablepassageway.
5.Removetheupperpartof the
cable slightly from the back
panel of the appliance, pull the
powersupplycableupwardsand
take it out [fig. 16].
To connect the new power
supplycable,reversethepro-
cedure.
It is important for your
safety that you reassemble
all parts and screws used.
8. Never pull on the supply
cable or the washing
machine to disconnect it
from the wall socket: it is
extremelydangerous.
9. While the appliance is
functioning, do not touch
the drain water as it could
reach very high
temperatures. The
appliance door, during
wash cycles, tends to
become hot; ensure that
children do no touch it.
Never force the washing
machine door because
this could damage the
safety lock which prevents
accidentalopeningwhenthe
nachine is working. Allow a
fewminutesattheend ofthe
program for the lock to
release.
10. In case of malfunctioning,
first close the water tap
and unplug the appliance
fromthewall socket;donot
under any circumstances
touch internal parts in order
toattemptrepairs.
Ionlywant anauthorised
specialisedtechnician with
original Indesitspare parts!
Fig. 13 Fig. 14 Fig. 15 Fig. 16
NL
F
15 Instructions for installation and use

We're as close to you as your telephone
For direct access to Genuine Indesit Spare Parts and Accessories,
call08705585850andspeaktoourskilledstaffwhocan helpyou toidentifyandpurchasetheitemyourequire.
For a Rapid Response to a problem with your appliance, call 0870 607 0805. We're open from Monday to
Saturday(8am-5.30pmweekdays,9am-5pmSaturday).WehaveourowndepartmentofhighlytrainedIndesit
service staff. For most calls, our Service Engineer can fix the problem on the first visit.
Please have the following details to hand when you ring us:
Thenatureoftheproblem,theModelNumberandtheSerialNumber.
Thesenumbers can be foundontheappliance and on theportionofthe Registration Card whichyouretain.
Stay in touch
THANKYOU for choosing an Indesit appliance. We are confident
you have made a good choice and that your new appliance will give
many years of excellent service.
And we're there when you need us.
Registeryourpurchase
now
This will confirm your entitlement to enter our quarterlyprizedraw
where you have the possibility to recover the cost of your purchase.
Simply complete andreturn the RegistrationForm suppliedwith the
appliance documents, using the FREEPOST envelope supplied. Or
call the Registration Hotline on 0870 010 4305.
Instructions for installation and use 16

17 Instructions for installation and use

Instructions for installation and use 18

12/2001- 195032734.00- XEROXBUSINESSSERVICES- DOCUTECH
Merloni Elettrodomestici
Viale Aristide Merloni 47
60044 Fabriano
Italy
Tel [phone]
Fax [phone]
www.merloni.com
Leader for young Europe