Inmotion controls 310 Series User manual

INMOTION Controls, Inc.
INSTALLATION & OPERATION
MANUAL
INMOTION Controls Series 310
March, 2006

2
Warranty
INMOTION Controls, Inc. guarantees that this product meets its published specification
at the time of shipment from the factory. Under proper installation, it should work as
expected. However, INMOTION Controls, Inc. does not guarantee that operation of the
310 Series Radio Control system is error-free or without interruption.
This equipment is warranted against defects in materials and workmanship for a period
of one year from the date of shipment. During the warranty period, INMOTION
Controls, Inc. is responsible for necessary repairs, as long as the product can be proved
to be defective.
For warranty service or repair, this product must be returned to our factory. Customer is
responsible for shipping charges to INMOTION Controls, Inc., while INMOTION
Controls, Inc. will pay return shipping charges.
This warranty does NOT include consumable parts, such as joystick, batteries, fuses,
buttons, and relays or damage from normal wear and tear. Furthermore, this warranty
does NOT cover defects caused by misuse, neglect, accident, failure to follow
instructions, improper installation, improper or insufficient maintenance, unauthorized
modification, unavoidable natural essential, improper operation, ignorance of
environmental specifications, improper software/interfacing, fire, or acts of God.
No other warranty is expressed or implied, except for the above mentioned
The remedies provided herein are the buyers’ sole and exclusive remedies.
INMOTION Controls, Inc. shall not be liable for any direct/indirect, special,
incidental or consequential damages.

3
Operating Precautions
ATTENTION
Due to the complex nature of the equipment, it is necessary to read the entire
manual before installation.
Never dismantle equipment by any unauthorized personnel, or equipment may
be damaged.
This Manual is for reference only; please call your distributor if further assistance
is required.
This equipment has been strictly tested for quality before delivery from our
factory. However, it must not be used in extremely dangerous situations, or
where damage may result.
After operating, please shut off main power in Crane, the power to Receiver, and
remove Transmitter key.
Transmitter should be placed safely when not in use to avoid accidental pressing
of buttons.
The Crane should be equipped with main power Relay, Limit Switch and other
required safety devices.
The GND (ground) of Receiver must be connected with metal part of Crane, or
electrical shock will occur.
Do not use this device during electrical storm, or high electrical interference
conditions.
Ensure Transmitter batteries are in good condition and power for Receiver is
normal.
Installation and maintenance should be done only while the Crane’s main power
and Receiver’s power are OFF, to prevent electrical shock.
Contents of the Manual may be amended by the manufacturer without notice.
The manufacturer may introduce new functions to the equipment as necessary;
therefore, the descriptions may change.
The patent and related documents for this equipment belong to INMOTION
Controls, Inc. and are not allowed to be used by others without written
permission.

4
Series 310 is manufactured with many patents developed and owned by
INMOTION Controls and its related enterprises.
PRECAUTIONS
After Operating Series 310, please press EMS mushroom to shut off main power
in the Crane & Receiver and remove Transmitter key.
Stop operating when slow-response occurs due to insufficient Transmitter power,
beyond the remote control range, or sever interference.
Remove the batteries when the equipment won’t be used for a long period.
Operators must be in good health and have good judgment in regards to safety.
Remote Control operator must have adequate training and related license to
avoid danger.
Series 310 Transmitter is durable and weather-resistant, but care should be
taken not to subject it to severe impact or pressure.
Series 310 is suitable for use in diverse industrial environments, and adequate
operating and maintenance will extend system’s life.
Check EMS mushroom and the other security functions of Series 310 system
before daily operation.
Press EMS mushroom when malfunctions or abnormal conditions occur.
Operator must be familiar with the following Emergency Procedures before
operating.
EMERGENCY PROCEDURES
In case of emergency, please follow the steps below and ask the distributor for service
immediately.
Press EMS mushroom
Turn the security key to the “OFF” position
Remove the batteries and key
Shut off the main power of the Crane and discontinue the operation
Contact the distributor to find out possible causes

5
Standard Accessories
A standard and full set of Series 310 consists of:
(1) Transmitter, 2 units (2) Receiver, 1 unit

6
Operation
TRANSMITTER CONFIGURATION

7
RECEIVER CONFIGURATION

8
GENERAL OPERATION
Turn on the main power switch of the equipment (Crane).
Install 2 AA batteries in the battery box in the Transmitter. Make sure the “+” and
“-“ directions are correct.
Attach Transmitter battery door with screws.
Insert security key in the “OFF” position.
Turn the keyswitch clockwise to the “ON” position, then continue to turn it to the
“START” position to power-on.
Note: LED indicator will flash with red color if proper procedures are not
followed.
Operate Transmitter by pressing each pushbutton.
After operation, perform the following procedures in sequence:
(1) Press EMS mushroom
(2) Turn rotary key switch counter-clockwise to the “OFF” position
(3) Remove key and keep it in a safe place
(4) Switch main power off to the equipment (Crane)
(5) Remove batteries if not used for a long period of time
Note: Transmitter has power indicating functions with LED display.
← “Green Color” –The LED will flash green when battery power is sufficient.
→ “Red Color” –The LED will flash red when the power is low.
The operating distance will become shorter and intermittent when
the batteries are low.
Replace with new batteries when battery power is low.
! DO NOT USE RECHARGEABLE BATTERIES !

9
Receiver Voltage Selection
There are two types of power voltages (DC and AC) available for the Series 310.
1) DC Type:
Input Voltage: 12~24 VDC
Relay Contact: 10A-36 VDC
2) AC Type:
Three different AC transformers: 48/110/220V, 48/220/380V, 110/220/380V.
Please disconnect the Receiver’s power, select the proper voltage, and plug in
the connector.
SWITCH THE PLUG TO CHOOSE VOLTAGE
Note: Standard Systems are 48/110/220 VAC. If any others are required, please
specify when ordering.

10
ID-Code Remote Setting
ID-Code remote setting allows the user to pair the new Transmitter or Receiver if one of
them is damaged. Using ID-Code remote setting will make both the Transmitter and
Receiver have the same ID-Code.
1) Please make sure of the following conditions before ID-Code remote
setting:
Both Transmitter and Receiver are of the SAME model and frequency.
Place the Transmitter as close as possible to the Receiver to avoid
interference.
Turn off the Receiver power more than 10 seconds and turn it on again.
2) ID-Code remote setting Instructions:
Press and hold the Transmitter EMS button.
Press UP pushbutton and hold it.
Press DOWN pushbutton 4 times and release “EMS & UP” pushbuttons
when the red light on the Transmitter is flashing.
Start the system as usual.
! ATTENTION !
In case ID-Code remote setting fails, repeat the instructions above within 4
minutes.
ID-Code remote setting is available for ID Code only. It will not change
function settings.
Within the operating distance, all same model systems on the same
frequency will be paired with the Transmitter’s ID Code.
A jumper added inside the receiver is necessary to enable ID-Code remote
setting function.

11
Changing the Frequency
It is easy to change the frequency of the Series 310 simply by replacing corresponding
frequency crystals in both the Transmitter and the Receiver.
Note: To replace a new crystal, please note that there are two kinds of
frequencies (VHF and UHF) available. The indication of VHF or UHF is
shown on the PC board with a check mark “V”. Please make sure not to
replace a VHF crystal unit into a UHF PC board, or vice versa.
Instructions:
1. Pry up the crystal with a flathead screwdriver.
2. Remove the crystal from the system.
3. Use needle nose pliers to straighten both pins of the new crystal.
4. Insert the new crystal vertically into the PC board.
5. Press the new crystal down into the socket.
Attention: The Transmitter frequency will be different from the Receiver
frequency. For example, the transmitter crystal are labeled
T01 thru T40 and receiver crystals are labeled R01 thru R40.

12
Batteries
Two AA size alkaline batteries are required for the Transmitter.
The LED will flash green when the battery power is sufficient.
The LED will flash red when the battery power is low.
The operating distance will become shorter and intermittent when the battery is
low.
Replace with new battery when battery power is low.
! DO NOT USE RECHARGEABLE BATTERIES !

13
Wiring Diagram
INMOTION-310