INNOVAPLAS Lumi-o MAJESTIC 8000 User manual

REV. 03/05/2020 PN: PG:1
MAJESTIC 8000 WITH CLASSIC LADDER 6004
Sand
15 lbs
Sand
Required tools (not included)
1) Insert the two 39" posts into
the step recesses and secure
them in place with the bolts,
washers and nuts provided.
2) Slide the two spacers on the
top post. Do not secure yet.
3) Insert the handrail over the left
side posts. Secure it using the
screws provided.
A
Contents of accessory box SKU # 8000 Contents of the ladder box SKU # 6004
SCREW KIT 140-0050
x2 x4 x4
x26
(2 ½ IN.)
x2
x2
(1 ¾ IN.)
(not included)
Step shell
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
SCREW KIT 140-0062
x4 x4 x4
(3 IN.)
(1 ¹⁄2 IN.)
x6
(³⁄4 IN.)
x10
AB C D E
x6
x2
(1 IN.)
A
(³⁄4 IN.)
D B C
FG
Security strap
x2
x2
x2
x2
x4
x2
A weather-resistant
padlock is
recommended.
Maximum functional
width of 1/4 inch.
Phillips #2
Phillips #3
7/16 wrench
3/8 drill bit
5/16 drill bit
Phillips bit
x4
D
WARNING
Install the step on a flat surface.
Do not jump or dive from the step or ladder.
Remove the step from water when temperatures drop below freezing.
In winter, the step should be stored in an area protected from snow.
Never lift the step by its handrails.
Use BATTERY operated tools to avoid electric shock near water.
Ensure no corrosive materials are added to the step or harware kit.
The step must be installed per manufacturer’s instructions.
File off all stripped or sharp edges before assembly to avoid injuries
and liner damage.
The manufacturer is not responsible for damages or injuries caused
by improper installation or use of product.
To ease the installation of handrails and bolts, use a screwdriver to
line up the holes.
1 year on step and ladder
1 year on hardware.
MANUFACTURER WARRANTY
A
x4
x4
x4
B
C

REV. 03/05/2020 PN: PG:2
MANUFACTURER WARRANTY
1 year on step and ladder
1 year on hardware.
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
B
x8
1) Slide the platform on the
flanged post.
2) Insert the short 29.25" hollow
post, on the other side, through
the spacers and platform.
3) Insert the two
small handrails
over the posts.
Don’t secure yet.
C
1) Make sure to leave a
1/4" clearance between
the bottom spacer and
the top of the step.
Secure in place with
the screws provided.
2) Measure 12"
between the two
spacers. Secure
in place with the
screws provided.
3) Don’t secure
the platform yet.
x2 x2 x2
4) Once inserted in the
spacers, use the 29.25"
hollow post as a pivot to
slide the flanged post
on the other side.
Drill two 5/16” holes.
12"
1/4"
MAJESTIC 8000 WITH CLASSIC LADDER 6004
GB C
D
D
1) Insert the six Step CupsTM in
the holes under the step.*
x6
D2) With a flat screwdriver, compress
the Step Cup mushroom ring while
pushing it into the hole.
CAUTION
D1) Insert half of the Step Cup mushroom
ring in the hole, at a 45 degree angle.
D3) Twist the Step Cup to ensure that
the mushroom ring has entirely cleared
the wall thickness. If it has, the suction
cup should rotate freely.
Failing to install the Step Cup
TM
system will greatly reduce the steadiness of the step and will void the
manufacturer warranty.
* View step cups installation tips on YouTube:
https://www.youtube.com/watch?v=W5RH1VNxpu0
E
Sand
15 LB
1) Fill the ballast with sand. The
approximate weight should be 15
lbs.
2) Screw the lid in place and
align the cover ribs with the
holes in the ballast base.
3) Fasten the cover to the
ballast base with the four
screws provided.
x4
D
Align holes
5) Secure the flanged post with the bolts,
washers and nuts provided.
5/16 drill bit

REV. 03/05/2020 PN: PG:3
MANUFACTURER WARRANTY
1 year on step and ladder
1 year on hardware.
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
MAJESTIC 8000 WITH CLASSIC LADDER 6004
F
*MINIMUM 1"
CAUTION
1) Slowly submerge the step
into the pool. Make sure you do
not damage the pool liner in
the process.
2) Angle the whole step so that
it is entirely under water. Purge
all the air from under the steps.
3) Apply firm pressure on the
step to allow the Step Cup to
stick on the pool bottom.
4) Drop the ballast in the step
hole.
To prevent pool liner puncture, keep a minimum 1" gap between the pool liner
and the rear underside of the step.
G
Security strap
x2
x2
F
1) Once the step is in
the pool secure the
platform to the top seat
(see illustration) using
the two straps provided.
OPTIONAL:
Once the pool step has been
completely assembled and
secured to the pool, attach the
2 screws supplied through the
platform to the top seat of your
pool to provided a more rigid
assembly.
H
1) Trace a line on each post at 39 inches from the
ground for 48’’ and 52’’ pools. If you have a 54’’ pool,
trace a line at 40.5 inches from the ground.
2) Slide the pivot blocks onto the posts and line up
with the traced marks. Secure with the screws
provided.
3) Attach the ladder base to the bottom of the posts
with the screws provided.
4) Slide the posts through the platform. Slide the lock
over right post between the platform and the handrail.
Secure the platform using the screws provided.
5) Slide the posts through the handrails. Insert the post
covers into the handrails. If they protrude too much,
raise the handrails until the post covers are seated
securely on the posts. Secure the short handrails in
place with the screws provided.
x18
D
A
D
LOCK
I1) Attach the ladder to the pivot blocks with
the bolts, washers and nuts provided.
x2
x2
x2
A
B
C
align for 48''
& 52'' pools
align for 54’’
Use sliding lock as a guide to drill hole into
ladder in up position. Use a 3/8’’ drill bit with
a cordless drill.
**PADLOCK REQUIRED**
SWING THE LADDER UP
AND LOCK IN PLACE WHEN
THE POOL IS NOT IN USE
TO PREVENT DROWNING
AND UNAUTHORIZED
ENTRY.
WARNING
3/8 drill bit