KidKraft PORTLAND SWING SET User manual

This swing set features the KidKraft “EZ UP” alignment hinge for
quick and easy fort frame assembly in Step 2 - 7.
The living hinge is not required for swing set structural integrity.
Complete the swing set build by following the instruction manual
steps, guidelines, and all other proper maintenance and care to
achieve a safe and quality product.
“EZ UP” ALIGNMENT HINGE

PORTLAND SWING SET - F29190
9409190 Rev 10/29/2020
Table of Contents
Warnings and Safe Play Instructions..........pg. 2
Protective Surfacing Guidelines. . . . . . . . . . . . . . . pg. 3
Instructions for Proper Maintenance .........pg. 4
About Our Wood – Limited Warranty.......pg. 5-6
Keys to Assembly Success ....................pg. 7
Part ID .......................................pg. 8
Step-By-Step Instructions ...................pg. 18
Installation of I.D./Warning Plaque ......Final Step
10-14 Hrs
Two person
assembly
FORT
2-4 Hrs
Two person
assembly
TUBE SLIDE
26'5"
805 cm
30'2"
911 cm
F29190 - Portland Playset Safety Zone
[16' 9-5/16"]
511.3 cm
[10' 3-3/4"]
314.4 cm
To reduce the risk of serious injury or death, you must
read and follow these instructions. Keep and refer to
these instructions often and give them to any future
owner of this play system. Manufacturer contact information provided below.
OBSTACLE FREE SAFETY ZONE - 30’2″ x 26′5″ (9.11m x 8.05m) area requires Protective Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6’4”(1.93m)
CAPACITY - 9 Users Maximum, Ages 3to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries,
day cares or parks.
Warning. Only for demestic use.
WARNING
FOR OUTDOOR FAMILY DOMESTIC USE ONLY
INSTALLATION AND OPERATING INSTRUCTIONS
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244 USA
[email protected]
[email protected]
1.800.933.0771
972.385.0100
For online parts replacement visit
https://parts.kidkraft.com/
KidKraft Netherlands BV
Olympisch Stadion 8
1076 DE Amsterdam
The Netherlands
[email protected]
[phone] M-F from 09:00 to 17:30
(GMT+1)
For online parts replacement visit
https://parts.kidkraft.eu/

2
STRANGULATION HAZARD
• NEVER allow children to play with ropes, clotheslines,
pet leashes, cables, chains or cord-like items when using
this play-set or to attach these items to play-set.
• NEVER allow children to wear loose tting clothing,
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this play-set.
• NEVER allow children to wear bike or sport helmets
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can reduce
the likelihood of the play set tipping over and loose-ll
surfacing materials washing away during heavy rains.
DO NOT allow children to play on the playhouse until the
assembly is complete and the unit is properly anchored.
Never add extra length to chain or rope. The chains or
ropes provided are the maximum length designed for the
swinging element(s).
WARNING LABEL
Owners shall be responsible for maintaining the legibility
of the warning labels.
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet and
other hard surface creates a risk of serious injury or death
from falls to the ground. Install and maintain shock absorbing
material under and around play-set as recommended on page
3 of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 2m from any
obstruction such as a garage or house, fences, poles, trees,
sidewalks, walls, landscape timbers, rocks, pavement,
planters, garden borders, overhanging branches, laundry
lines, and electrical wires. (See OBSTACLE FREE SAFETY
ZONE on cover).
CHOKING HAZARD/SHARP EDGES & POINTS
Adult assembly required. This product contains small parts
and parts with sharp edges and points. Keep parts away from
children until fully assembled.
CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred
while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying
with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using
this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they
understand and follow them. Remember on-site adult supervision is required for children of all ages.
Warnings and Safe Play Instructions
WARNING
WARNING –Safe Play Instructions
Do not allow children to wear open toe or heel footwear
like sandals, ip–ops or clogs.
Do not allow children to walk, in front, between, behind
or close to moving rides.
Do not let children twist swing chains or ropes or loop
them over the top support bar. This may reduce the
strength of the chain or rope and cause premature failure.
Do not let children get off rides while they are in motion.
Do not permit climbing on equipment when it is wet.
Do not permit rough play or use of equipment in a
manner for which it was not intended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
Do not allow children to swing empty rides or seats.
Do not allow children to go down slide head rst or
run up slide.
Observe capacity limitations of your play-set. See front cover.
Dress children with well tting and full foot enclosing footwear.
Teach children to sit with their full weight in the center of the
swing seat to prevent erratic swing motion or falling off.
Check for splintered, broken or cracked wood; missing, loose,
or sharp edged hardware. Replace, tighten and or sand smooth
as required prior to playing.
Verify that suspended climbing ropes, rope ladders, chain or
cable are secured at both ends and cannot be looped back on
itself as to create an entanglement hazard.
On sunny and or hot days, check the slide and other plastic
rides to assure that they are not very hot as to cause burns.
Cool hot slide and rides with water and wipe dry prior to using.
Orientate slide such that it gets the least amount of exposure to
the sun.
WARNING:
Lawn swings are designed for use by children two years of
age and older. The use by children under the age of two can
result in entrapment between the seat and back rest because
the child’s body may pass through the opening, causing
entrapment of the child’s head. Such entrapment may result
in strangulation. NEVER place children in a rearward facing
position or with legs between the seat and backrest.

3
One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing
protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable
for the equipment height in accordance with ASTM F1292. There are different types of surfacing to choose from; whichever
product you select, follow these guidelines:
Loose-Fill Materials
• M
aintain a minimum depth of 9 inches (23 cm) of loose-fill materials such as wood mulch/chips, engineered wood fiber (EWF), or
shredded/recycled rubber mulch for equipment up to 8 feet (2.45 m) high; and 9 inches (23 cm) of sand or pea gravel for equipment up to 5 feet (1.5 m)
high. NOTE: An initial fill level of 12 inches (31 cm) will compress to about a 9-inch (23 cm) depth of surfacing over time. The surfacing will also
compact, displace, and settle, and should be periodically raked and refilled to maintain at least a 9-inch (23 cm) depth.
• U
se a minimum of 6 inches (16 cm) of protective surfacing for play equipment less than 4 feet (1.22 m) in height. If maintained properly, this
should be adequate. (At depths less than 6 inches (16 cm), the protective material is too easily displaced or compacted.)
NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface
can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and
environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are not adequate protective
surfacing. Ground level equipment -- such as a sandbox, activity wall, playhouse or other equipment that has no elevated play
surface-- does not need any protective surfacing.
• Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to
account for water drainage.
• Periodically rake, check and maintain the depth of the loose-fill surfacing material. Marking the correct depth on the play
equipment support posts will help you to see when the material has settled and needs to be raked and or replenished. Be sure to
rake and evenly redistribute the surfacing in heavily used areas.
• Do not install loose fillsurfacing over hard surfaces such as concrete or asphalt.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles
You may be interested in using surfacing other than loose-fill materials - like rubber tiles or poured-in-placesurfaces.
• Installations of these surfaces generally require a professional and are not “do-it yourself ” projects.
• Review surfacespecifications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that
the product has been tested to the following safety standard: ASTM F1292 Standard Specification for Impact Attenuation of Surfacing
Materials within the Use Zone of Playground Equipment. This report should show the specific height for which the surfaceis intended
to protect against serious head injury. This height should be equal to or greater than the fall height - vertical distance between a
designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing below - of your play equipment.
• Check the protective surfacing frequently for wear.
Placement
Proper placement and maintenance of protective surfacing is essential. Refer to diagram on front cover. Be sure to;
• Extend surfacing at least 6 feet (1.8 m) from the equipment in all directions.
• For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top
bar from which the swing is suspended.
• F
or tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet (1.8 m) in all directions.
Protective Surfacing-Reducing Risk of Serious Head Injury From Falls
From the CPSC Outdoor Home Playground Safety Handbook. At http://www.playgroundregs.com/resources/CPSC%20324.pdf
Denotes Use Zone with Protective Surfacing
Denotes Use Zone with Protective Surfacing
6 ft.
6 ft.
6 ft. (1.8m)
6 ft. (1.8m)
(1.8m)
6 ft.
(1.8m)
(1.8m)
6 ft.
(1.8m)
6 ft.
(1.8m)
Use Zone for Multi-Axis SwingsUse Zone for Single-Axis Swings

4
Instructions for Proper Maintenance
sand and repaint using a non-lead paint
splinteringof wood.
Check for sharp edges or protrudingscrew threads, add
washers if required.
fill protective surfacing materials to prevent compaction and
Check for looseness, damage ordeterioration. Should firmly
if necessary.
Check that bolts are secure and tight. Quick clips should be
completely closed and threaded clips screwed tight.
parts including swingseats, ropes, chains and attachments
Check that ropes are tight, secure at both ends and cannot
loop back as to create an entrapment.
Check all wood members fordeterioration, structural
damage and splintering. Sand down splinters and replace
deteriorated wood members. As with all wood, some
checking and small cracks in grain is normal.
basis is important maintenance to maintain maximum life
and performance oftheproduct.
Check the following at the beginning of the play season:
This will causesplinteringof wood.
Check for sharp edges orprotrudingscrew threads.
Add washers ifrequired.
materials to prevent compaction and maintain appropriate
Check twice a month during play season:
Check that they are secure and orientated correctly. Hook
should rotate freely and perpendicular to support beam.
Check swingseats, all ropes, chains and attachments for
fraying, wear, excessive corrosion ordamage.
Check once a month during play season:
To prolongtheir life, remove swings and store insidewhen
plasticparts may become morebrittle.
materials to prevent compaction and maintain appropriate
Check at the end of the play season:
If you disposeof your play set:
hazards at thetime it is discarded. Besure to follow yourlocal wasteordinances.
beyond T-Nut
flat washer
Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with
all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your
Play Set, it is important that you, the owner, properly maintain it.

5
About Our Wood
KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your
children’s use. Although we take great care in selecting the best quality lumber available, wood is still a
product of nature and susceptible to weathering which can change the appearance of your set.
What causes weathering? Does it affect the strength of my Play System?
One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood
at the surface is different than the interior of the wood. As the climate changes, moisture moves in or out
of the wood, causing tension which can result in checking and or warping. You can expect the following
due to weathering. These changes will not affect the strength of the product:
1. Checking is surface cracks in the wood along the grain. A post 4” x 4” (101mm x 101mm) will experience
more checking than a board 1” x 4” (25mm x 101mm) because the surface and interior moisture content
will vary more widely than in
thinner wood.
2. Warping results from any distortion (twisting, cupping) from the original plane of the board and often
happens from rapid wetting and drying of the wood.
3. Fading happens as a natural change in the wood color as it is exposed to sun-light and will turn a grey
over time.
How can I reduce the amount of weathering to my Play System?
At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount
of water absorption during rain or snow thus decreasing the tension in the wood. Sunlight will break down
the coating, so we recommend applying a water repellent or stain on a yearly basis (see your local stain
and paint supplier for a recommended product).
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your
child. However if you are concerned that a part has experienced a severe weathering problem please call
our consumer relations department for further assistance.
Complete and mail registration card to receive important product notifications and assure prompt
warranty service.

6
KidKraft Limited Warranty
MISSING OR DAMAGED PARTS:
KidKraft will replace any parts within 90 days from date of purchase found to be missing from or
damaged in the original packaging. See Fig.1
Fig. 1 Product Age (All Parts) Consumer Pays
0-90 Days from date of purchase $0 for Part + Free Shipping
DEFECTS IN MATERIAL AND WORKMANSHIP:
KidKraft warrants that this product is free from defects in materials and workmanship for a period of one
(1) year from the original date of purchase (dated sales receipt and/or product registration is required).
This one (1) year warranty covers all parts including wood, hardware, and all accessories (Such as
swings, rides, and slides). See Fig. 2
Fig. 2 Product Age (All Parts) Consumer Pays
91 Days to 1 Year $0 for Part + Free Shipping
WOOD ROT, DECAY, AND INSECT DAMAGE:
All wood carries a five (5) year warranty against rot, decay, and insect damage (dated sales receipt
and/or product registration is required). Refer tothe schedule below for charges associated with
replacement of wood parts under this Limited Warranty. See Fig. 3
Fig. 3 Product Age (Wood Parts) Consumer Pays
0 Days to 1 Year $0 for Part + Free Shipping
After 1 Year to 5 Year $0 for Part + Shipping & Handling
Over 5 Years 100% for Part (if available) + Shipping & Handling
This warranty applies to the original owner and registrant and is non-transferable. Regular maintenance
is required to ensure the integrity of this product. Failure by the owner to maintain the product according
to the maintenance requirements may void this warranty.
This Limited Warranty does NOT cover:
• Any inspection cost
• Labor and/or costs for replacement of any defective item(s), including but not limited to,
professional installer costs
• Incidental or consequential damages, including but not limited to, as a result of set relocation,
move and/or reinstall
• Cosmetic defects which do not affect performance or integrity of a part or the entire product
• Vandalism, improper use or installation, or acts of nature, including but not limited to, high winds,
fire, and flood
• Minor twisting, warping, checking, or any natural occurring properties of wood that do not affect
performance or integrity.
• Any KidKraft product purchased, including but not limited to, a non-approved retailer, auction
houses, second-hand, and as-is clearance items.
KidKraft products have been designed for safety and quality. Modifications made to the original product
may damage the structural integrity of the unit leading to failure and possible injury. KidKraft cannot
assume any responsibility for the modified products. Furthermore, modifications void all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a KidKraft
product be used in public settings such as schools, churches, playgrounds, parks, home and
professional day cares and the like. Such use may lead to product failure and potential injury. Public use
will void this warranty. KidKraft disclaims all other representations and warranties of any kind, express or
implied.

7
This identifies information that requires special
attention. Improper assembly could lead to an unsafe
or dangerous condition.
Where this is shown, 2 or 3 people
are required to safely complete the
step. To avoid injury or damage
to the assembly make sure to get
help!
Check that assembly is square
before tightening bolts.
Use a measuring tape to assure
proper location.
Check that set or assembly is properly level
before proceeding.
Pre-drill a pilot hole
before fastening screw
or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
Part Identification Key
On each page, you will find the parts
and quantities required to complete the
assembly step illustrated on that page.
Here is a sample.
Key Number: The first two digits
represent the step number. The third
digit represents the piece. Note that if
the part is used in multiple steps then
the number only reflects the first step it
is used in.
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
Proper Hardware Assembly
Lag screws require drilling pilot
holes to avoid splitting wood. Only
a flat washer is required. For ease of
installation liquid soap can be used
on all lag-type screws.
For bolts, tap T-Nut into hole with
hammer. Insert the hex bolt through
lock washer first then flat washer then
hole. Because the assemblies need to
be squared do not completely tighten
until instructed. Pay close attention to
diameter of the bolts. 5/16” (8mm) is slightly
larger than 1/4” (6.4mm).
Note: Wafer head bolts with blue lock
tight or a bolt with a Ny-Lok nut do
NOT require a lock washer.
Once the assembly is tightened, watch for exposed threads.
If a thread protrudes from the T-Nut, remove
the bolt and add washers to eliminatethis condition.
Extra washers have been provided for this purpose.
Use
Help
Use
Help
Measure
Distance
Square
Assembly
Use
Level
Pre-drill 1/8”(3mm) & 3/16”(5mm) Bit
Tighten
Bolts
CAUTION – Protrusion Hazard
Keys to Assembly Success
Tools Required
Quantity Key Number Part Description,
Part Size
2X 012 P
No Yes
Lag Assembly
Bolt Assembly
Flat Washer
Lag Screw
Hex Bolt
Lock
Washer
Flat
Washer
Before mounting Lag
Screw, use factory drilled
holes as guides to drill 1/8”
(3.2mm) pilot holes
T-Nut
(Hammer into place)
Do not crush wood!
If Bolt protrudes
beyond T-Nut
Use an extra
flat washer
• Tape Measure
• Carpenters Level
• Carpenters Square
• Claw Hammer
• Standard or Cordless Drill
• Rubber Mallet
• #1 Phillips, #2 Robertson
and Screwdriver
• Ratchet with extension
1/2” (13mm) & 9/16”(14 mm)
sockets
• Open End Wrench
1/2” (13mm) & 9/16”(14 mm)
• Adjustable Wrench
• 1/8”(3mm) & 3/16”(5mm)
Drill Bits
• 3/16”(5mm) Hex Key
• 8’ (2.4m) Step Ladder
• Safety Glasses
• Adult Helpers
• Pencil
3mm 5mm
ost 2 x 4 x 83” (5 cm x 10 cm x 210 cm)

8
Part Identification (Reduced Part Size) - BOX 1
1x - 9686 - 31.8 x 76.2 x 1251.0mm - 3839686
1 1/4" X 3" X 49 1/4"
1x - 9687 - 31.8 x 63.5 x 660.4mm - 3839687
1 1/4" X 2 1/2" X 26"
1x - 9688 - 25.4 x 76.2 x 635 mm - 3839688
1" X 3" X 25"
4x - 9689 - 76.2 x 76.2 x 186.6 mm - 3839689
3" X 3" X 7 3/8"
1x - 9691 - 31.8 x 63.5 x 1219.2 mm - 3839691
1 1/4" X 2 1/2" X 48"
1 1/4" X 3" X 36"
2x -
9696 - 31.8 x 76.2 x 914.4 mm - 3839696
8x - 9697 - 15.9 x 76.2 x 549 mm - 3839697
5/8" X 3" X 21 5/8"
1 1/4" X 3" X 18"
1x -
9699 - 31.8 x 76.2 x 457.2 mm - 3589699
1 1/4" X 3" X 18"
2x -
9746 - 31.8 x 76.2 x 457.2 mm - 3589746
2x - 9701 - 31.8 x 76.2 x 977.9 mm - 3589701
1 1/4" X 3" X 38 1/2"
1 1/4" X 3" X 34 1/2"
2x - 9702 - 31.8 x 76.2 x 876.3 mm - 3589702
4x - 9703 - 15.9 x 76.2 x 715.1 mm - 3589703
5/8" X 3" X 28 1/8"
1 1/4" X 3" X 29 15/16"
1x - 9704 - 31.8 x 76.2 x 759.9 mm - 3589704
1x - 9705 - 31.8 x 63.5 x 424.4 mm - 3589705
1 1/4" X 2 1/2" X 16 11/16"
1 1/4" X 3" X 17"
1x -
9709 - 31.8 x 76.2 x 431.8 mm - 3589709
1x - 9710 - 31.8 x 31.8 x 650 mm - 3589710
1 1/4" X 1 1/4" X 25 9/16"
1 1/4" X 3" X 45 7/16"
1x - 9715 - 31.8 x 76.2 x 1154.6 mm - 3839715
5x - 9717 - 15.9 x 133.4 x 482.6 mm - 3589717
5/8" X 5 1/4" X 19"

9
Part Identification (Reduced Part Size) - BOX 1
5/8" X 5 1/4" X 19"
2x - 9718 - 15.9 x 133.4 x 482.6mm - 3589718
2x - 9720 - 50.8 x 76.2 x 2063.9mm - 3839720
2" X 3" X 81 1/4"
1 1/4" X 3" X 20 1/4"
1x - 8965 - 31.8 x 76.2 x 514.4 mm - 3838965
1x - 9722 - 31.8 x 76.2 x 857.3 mm - 3839722
1 1/4" X 3" X 33 3/4"
15/16" X 3 1/4" X 35 5/8"
1x - 9723 - 23.8 x 82.6 x 905.7 mm - 3589723
2x - 9724 - 23.8 x 82.6 x 584.8 mm - 3589724
15/16" X 3 1/4" X 23"
15/16" X 3 1/4" X 30"
1x - 9725 - 23.8 x 82.6 x 761.2 mm - 3589725
1x - 9726 - 23.8 x 82.6 x 592.3 mm - 3589726
15/16" X 3 1/4" X 23 5/16"
15/16" X 4" X 23"
2x - 9729 - 23.8 x 101.6 x 584.8 mm - 3589729
1x - 9730 - 23.8 x 101.6 x 584.8 mm - 3589730
15/16" X 4" X 23"
1x - 9292 - 28.6 x 1270 x 801.7 - 37589292 1 1/8" X 50" X 31 9/16"
5/8" X 3" X 19"
1x - 9719 - 15.9 x 76.2 x 482.6 mm - 3589719

10
4-1/4" X 36" X 92"
1x - 9297 - 108 x 914 x 2336.6mm - 37839297
Part Identification (Reduced Part Size) - BOX 1
37839296 - Open Panel - 1pc
39839402 - Swing Arm -1pc
39839403 - Export top -1pc
9327884 - Hinge - 1pc
If you need to order parts, please order below part #
S0 - 52933505 - Truss Screw #8 x 7/8” - 1pc
FW1 - 51103200 - Washer Flat 1/4” - 1pc
LS3 - 52213230 - Lag Screw 1/4 x 3 Yellow Zinc - 1pc
S0 - 52933505
9327884 - 52213230
LS3
37839296
39839403
39839402
39839402
FW1 - 51103200

11
2x - 9700 - 31.8 x 76.2 x 876.3 mm - 3589700
1 1/4" X 3" X 34 1/2"
5/8" X 4 1/2" X 38 1/2"
1x - 9706 - 15.9 x 114.3 x 977.9 mm - 3589706
2x - 9707 - 15.9 x 114.3 x 977.9 mm - 3589707
5/8" X 4 1/2" X 38 1/2"
5/8" X 4 5/16" X 38 1/2"
1x - 9708 - 15.9 x 109 x 977.9 mm - 3589708
3x - 9711 - 15.9 x 76.2 x 914.4 mm - 3589711
5/8" X 3" X 36"
1 1/4" X 2" X 42 1/2"
2x - 9712 - 31.8 x 50.8 x 1079.5 mm - 3839712
4x - 9713 - 31.8 x 50.8 x 691.1 mm - 3839713
1 1/4" X 2" X 27 3/16"
1 1/4" X 5 1/4" X 36"
1x - 9714 - 31.8 x 133.4 x 914.4 mm - 3839714
2x - 9716 - 34.9 x 63.5 x 1332.8 mm - 3589716
1 3/8" X 2 1/2" X 52 1/2"
1x - 2614 - 76.2 x 133.4 x 2235.2 mm - 3832614 3" X 5 1/4" X 88"
3" X 3" X 50 15/16"
1x - 2615 - 76.2 x 76.2 x 1294.3 mm - 3832615
1x - 2616 - 23.8 x 82.6 x 1181.1 mm - 3832616
15/16" X 3 1/4" X 46 1/2"
1 1/4" X 1 1/4" X 41 15/16"
1x - 9721 - 31.8 x 31.8 x 1064.8 mm - 3839721
2x - 9727 - 23.8 x 82.6 x 584.8 mm - 3589727
15/16" X 3 1/4" X 23"
15/16"
X 3 1/4" X 19 11/16"
2x - 9728 - 23.8 x 82.6 x 500.2 mm - 3589728
Part Identification (Reduced Part Size) - BOX 2

12
1 1/4" X 2 1/2" X 15"
8x - 9731 - 31.8 x 63.5 x 381 mm - 3839731
2x - 9732 - 31.8 x 76.2 x 530 mm - 3839732
1 1/4" X 3" X 20 7/8"
1 1/4" X 1 1/4" X 36"
1x - 9735 - 31.8 x 31.8 x 914.4 mm - 3839735
Part Identification (Reduced Part Size) - BOX 2
2x - 9685 - 31.8 x 76.2 x 1219.2 mm - 3839685
1 1/4" X 3" X 48"
1 1/2" X 1 1/2" X 41 13/16"
2x - 9690 - 38.1 x 38.1 x 1062.8 mm - 3839690
8x - 9692 - 15.9 x 114.3 x 880.6 mm - 3589692
5/8" X 4 1/2" X 34 11/16"
2x - 9693 - 15.9 x 114.3 x 880.6 mm - 3589693
5/8" X 4 1/2" X 34 11/16"
1 1/4" X 2 1/2" X 16 9/16"
4x - 9694 - 31.8 x 63.5 x 421 mm - 3839694
4x - 9695 - 31.8 x 31.8 x 285.9 mm - 3839695
1 1/4" X 1 1/4" X 11 1/4"
1 1/4" X 3" X 18"
1x -
9698 - 31.8 x 76.2 x 457.2 mm - 3589698
1 1/4" X 3" X 18"
1x -
9745 - 31.8 x 76.2 x 457.2 mm - 3589745
1x - 9293 - 28.6 x 1270 x 807.5 mm - 37589293 1 1/8" X 50" X 31 13/16"

13
Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) - BOX 2
1x - 9295 - 108 x 914 x 2336.6 - 37839295
4 1/4" X 36" X 92"
37839294 - SW Panel - 1pc
39839402 - Swing Arm -1pc
39839403 - Export top -1pc
9327884 - Hinge - 1pc
S0 - 52933505 - Truss Screw #8 x 7/8” - 1pc
S0 - 52933505
9327884
If you need to order parts, please order below part #
37839294
39839403
39839402
39839402
- 52213230
LS3
LS3 - 52213230 - Lag Screw 1/4 x 3 Yellow Zinc - 1pc
FW1 - 51103200 - Washer Flat 1/4” - 1pc
FW1 - 51103200

14
Hardware Identification (Actual Size)
30x - S3
- #8 x 2-1/2" - (52043522)
63.5mm
36x - S4
- #8 x 3" - (52043530)
76.2mm
170x - S20
- #8 x 1-3/8" - (52043516)
34.9mm
63x - S0
- #8 x 7/8"
- (52933505)
22.2mm
36x - LW2 - 5/16" - (51303300)
7.9mm
23x - LN2 - 5/16"
-
(54303300)
7.9mm
24x - LW1 - 1/4" - (51303200)
6.4mm
119x - FW2 - 5/16" - (51103300)
7.9mm
39x - FW1 - 1/4" - (51103200)
6.4mm
5x - FW0 - 3/16" - (51103100)
4.8mm
60x - LN1 -
1/4
- (54303200)
6.4mm
12x - S11
- #8 x 2" - (52043520)
50.8mm
4x - S18
- #6 x 1" - (52013910)
25.4mm
5x - BN1 - 1/4"
-
(54803200)
6.4mm
34.9mm
4x - WL3 - 1/4 x 1-3/8"- (52613216)
17x - S6 - #12 x 1" - (52433610)
25.4mm
8x - FW6 - #12 - (9299500)
33x - WL5
- 1/4 x 2-1/2" - (52613222)
6.4 x 63.5mm
58x - S7
- #12 x 2" - (52433620)
50.8mm
5x - S10
- #8 x 1" - (52433510)
25.4mm
42x - TN2 - 5/16"
-
(54503300)
7.9mm
34x - TN1 - 1/4"
-
(54503200)
6.4mm
4x - S24
- #10 x 4" - (52043940)
25.4mm
40x - S37
- #7 x 5/8" - (52433009)
15.8mm

15
1x - D4 - #2 x 2 - (9200014)
14x - H2 -
1/4 x 2" - (53703220)
6.4 x 50.8mm
6.4 x 38.1mm
4x - H12 -
1/4 x 3"
- (53703230)
6.4 x 76.2mm
13x - G21 -
5/16 x 3-3/4"
- (53703333)
7.9 x 95.3mm
10x - G4 -
5/16 x 4"
- (53703340)
7.9 x 101.6mm
49x - PB1 - 1/4 x 3/4 " - (53413203)
6.4 x 19.1mm
5x - PB2 - 1/4 x 1-1/4 " - (53433212)
11x - PB6 - 1/4 x 1 " - (53413210)
6.4 x 25.4mm
6.4 x 31.8mm
Hardware Identification (Actual Size)
14x - G7 -
5/16 x 5-1/2"
- (53703352)
7.9 x 139.7mm
13x - H8 -
1/4 x 4-1/4"
- (53703241)
6.4 x 108mm
4x - G8 -
5/16 x 2"
- (53703320)
7.9 x 50.8mm
1x - WB8 -
5/16 x 2-3/8"
- (53613326)
7.9 x 60.3mm
4x - WB10 -
5/16 x 2-5/8"
- (53613329)
7.9 x 66.7mm
11x - WB7 -
5/16 x 3"
- (53613330)
7.9 x 76.2mm
10x - WB2 -
5/16 x 1-3/8" - (53613316)
7.9 x 25.4mm
2x - H10 -
1/4 x 2-1/4"
- (53703221)
6.4 x 57.2mm
1x -
3/16" - (9200022)
8pc. H1 - 1/4 x 1-1/2"
- (53703212)
Note: Hardware bag includes extra hardware

16
1x - (3201950) (6pk)
4x -
(3200172)
1x
- (3200106)(4pk)
1x - (3329190) (5pk)
1x - (3200145)(2pk)
1x - (3200718)(7pk)
7x - (9290318)(1pk)
2x -
(9330518)
1x - (3320255)
2x - (9320130)
1x -
(3320161)
2x - (3320704)
1x
- (3310122)
1x - (3310123)
9x - (3310121)
1x
- (3310124)
31x - (54902200)
2x - (9200157)
1x - (9200156)
1x - (53452209)
30x - (53453202)
1x - (9200168)
1x -
(9320374)
1x - (3200155)
1x -
(3209190)
1x - (3200143)
1x - (9200244)
1x -
(9200243)
1x - (3310132)
Part Identification (Reduced Part Size)
1x - (3320353)
2x -
(7310149)
1x - (3320240)(2pk)
1x -
(3320341)
1x - (9201570)
(1pk)
1x - (3200132)
(9pk)
10x - TNR 4 Clamp Ring
(9300130) (Green)
10pcs number 3300130

17
24x - (3799193)
8x - (3799194)
1x - (5799192)
1x - (3759190)
1x
x6
x4
x2
x4
x6
- (3720001)
1x - (3720002)
Part Identification (Reduced Part Size)

18
B. If there are any missing or damaged pieces or you need assistance with
assembly please contact the consumer relations department directly. Call us
before going back to the store.
Step 1: Inventory Parts - Read This Before Starting Assembly
• Please refer to Page 7for proper hardware assembly.
• Each step indicates which bolts and/or screws you will need for assembly, as well as
any at washers, lock washers, t-nuts or lock nuts.
A. This is the time for you to inventory all your hardware, wood and accessories,
referencing the parts identication sheets. This will assist you with your assembly.
• The wood pieces will have the key number stamped on the ends of the boards.
Organize the wood pieces by step, as per the key numbering system below.
Quantity Key Number Part Description,
Part Size
2X 012 Post 2” x 4” x 83” (5cm x 10cm x 210cm)
C. Read the assembly manual completely, paying special attention to ANSI warnings;
notes; and safety/maintenance information on pages 1 - 7.
D. Before you discard your cartons ll out the form below.
• The carton I.D. stamp is located on the end of each carton. The tracking number is
located on the KidKraft ID Plaque (9320374).
• Please retain this information for future reference. You will need this information if you
contact the Consumer Relations Department.
CARTON I.D. STAMP: __ __ __ __ __ __ ___ (Box 4)
CARTON I.D. STAMP: __ __ __ __ __ __ ___ (Box 5)
CARTON I.D. STAMP: __ __ __ __ __ __ ___ (Box 6)
CARTON I.D. STAMP: __ __ __ __ __ __ ___ (Box 1)
CARTON I.D. STAMP: __ __ __ __ __ __ ___ (Box 2)
CARTON I.D. STAMP: __ __ __ __ __ __ ___ (Box 3)
MODEL NUMBER: F29190
TRACKING NUMBER (from ID Plaque):
[phone]
[email protected]
For online parts replacement visit
https://parts.kidkraft.eu/
1.800.933.0771 or 972.385.0100
[email protected]
[email protected]
For online parts replacement visit
https://parts.kidkraft.com/

19
Hardware
2 x
TN1
TN1
TN1
Step 2
1 x 108 x 914 x 2336.8mm (4-1/4” x 36” x 92”)
Wood Parts
9295
9295