Innovashelf T-loc 2015-10ds User manual

T-LOC

2015-10DS

Seat shelf against wall,

drill hole and secure with

self-tapping trim screw

Steel only

Outer Ring - Concrete

12 [Steel Stud Only] 3

4 5

6 [Steel Stud]

6 [Drywall]

Align template with line

[Steel Stud Only]

Drill to, but not through,

stud with 1/2" bit

Drill with 1/4" bit,

then with 1/2" bit

A. Insert snaptoggle

B. Orient vertically with cap up

C. Tighten retainer

D. Snap off plastic legs

A/B

B. Thread 1/2" grub

screw into base plate

B. Thread 1" grub

screw into base plate

A. Slide bolt through

base plate and drywall plate

and thread into snaptoggle

(1" grub screw not used for drywall)

(1/2" grub screw and drywall plate not used for steel stud)

A. Slide bolt through

base plate and thread

into snaptoggle

Find stud center and

draw 1" vertical line

Draw horizontal line

at installation height

Discover more products by visiting us

online. Just scan this QR code or visit

www.innovashelf.com to find inspiration

photos, bracket specs, other products,

and information about purchasing more

brackets or buying wholesale.

Lock bracket arm

into base plate

Adjust angle with

3/16" allen wrench

to level bracket

Measuring tape

Laser level (optional)

Level

Stud finder

[2] Shelf bracket arms

[2] Base plates

[2] 1/2" grub screws

[2] 1" grub screws

[2] Drywall plates

[2] Snaptoggles

[2] 2.5" bolts

[2] 1.5" self-tapping trim screws

[2] 1" self-tapping trim screws

[1] 5/32" drill bit

Pencil

Impact driver

#1 square drive bit

Phillips screwdriver

Drill

1/4" drill bit

1/2" drill bit

3/16" Allen wrench

Tools Needed

Installation Instructions

Step 1: Using a laser level or level as a guide, draw a horizontal line on the selected wall or area at the desired installation height

taking into account the thickness of the shelf top. The line must be as long as the shelf that's being installed.

Step 2 [Steel Stud Only]: Use a stud finder to find wall studs to mount your brackets on within the length of the horizontal line. Use

a pencil to draw a vertical line in the center of each stud up 1" from the horizontal line.

Step 3: Place the provided adhesive mounting template on the wall where the shelf bracket will be fastened. The top edge of the

template should be on the horizontal line. For steel studs, the vertical center line should match the vertical line on the wall.

Step 4: Pre-drill the top hole using a drill and a 1/4" bit, drilling through the center of the top dot on the mounting template. Finish

the hole with a 1/2" bit. For steel stud installations, use a 1/2" bit to drill the bottom hole to, but not through, the stud.

Step 5: Insert the snaptoggle into the top hole, and turn it to orient the wings vertically with the cap up. Tighten the center retainer

and snap off the plastic legs.

Step 6 [Drywall]: Align the hole on the drywall plate with the top hole on the base plate, then slide the 2.5" bolt through both holes

and thread it into the snaptoggle. Hand-tighten with a screwdriver. Thread the 1/2" grub screw into the base plate.

(The 1" grub screw is not used for drywall applications)

Step 6 [Steel Stud]: Slide the 2.5" bolt through the top hole of the base plate and thread it into the snaptoggle. Hand-tighten with a

screwdriver. Thread the 1" grub screw into the base plate.

(The 1/2" grub screw and drywall plate are not used for steel stud applications)

Step 7: Lock the shelf bracket arm into the base plate.

Step 8: To level the bracket, place a level on top of the bracket arm and, using a 3/16" Allen wrench, rotate the grub screw

clockwise or counter-clockwise. Make sure to level the brackets with each other.

Repeat steps 3-8 for each shelf bracket.

Step 9: Slide the shelf onto the shelf brackets and push it firmly against the wall. Measure 2" out from the lines drawn in step 2

and use a drill with the 5/32" bit to drill to, but not through, the bracket. Use an impact with a #1 square drive bit to drive a 1"

self-tapping screw (for shelves with 1/2" top thickness) or a 1.5" self-tapping screw (for shelves with more than 1/2" top

thickness) through each hole and into the brackets to secure the shelf to the wall.

Parts Included