Vivo STAND-V102F User manual

Dual Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v102f
SKU: STAND-V102F
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A (x2)
VESA Plate
B(x1)
Arm
C(x1)
Base
M-A (x8)
M4x12
M-D (x8)
M5x16
J (x1)
6mm Allen
Wrench
M-F (x8)
Spacer
M-E (x8)
D5 Washer
D(x1)
Pole
E(x1)
Cable Clip
F (x2)
Thumbscrew
G(x2)
Bolt
H (x3)
Bolt
I (x1)
4mm Allen
Wrench
M-C (x8)
M5x12
M-B (x8)
M4x16
K (x1)
Pole Cap
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD
OR BACKWARD.
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

3
ASSEMBLY STEPS
STEP 1
Insert pole cap (K) to top of pole (D).
TOOLS NEEDED
Phillips
Screwdriver
STEP 2
Assemble pole (D) to base (C) with bolts (H) using 4mm Allen wrench (I).
17.6lbs
Per Arm
(8 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
K
D
D
C
H
I

4
STEP 3
Install swivel arms (B) and cable clip (E) to pole (D). Fasten the bolt with the supplied 6mm Allen
wrench (J).
STEP 4
OPTION A: Flat Back Monitor
For flat back monitor, install VESA plate (A) to monitor using bolts (M-A) or (M-C) and washers (M-E).
OPTION B: Curved Back Monitor
For curved back monitor, install VESA plate (A) to monitor using bolts (M-B) or (M-D), washers (M-E),
and spacers (M-F).
E
D
B
J
M- A
M- C
M- E
A
M- B
M- D
M- E
M- F
A

5
STEP 5
Manage the cables using the installed cable clips.
STEP 6
Slide the monitors onto the heads of swivel arms (B). Install thumb screws (F) using bolts (G). Make
sure the screws are installed before you rotate the monitors. If needed, adjust the bolt on the side of
the hinge behind the VESA plate to tighten or loosen the tilt angle using 6mm Allen wrench (J).
J
G
F
12

6
STEP 7
Store the Allen wrench in cable clip (E) for future use.
I
J

7
STEP 9
Adjust monitor alignment using thumb screws (F). If needed, use 6mm Allen wrench (J) to turn screw.
STEP 8
Be careful not to extend the arms too far forward or backward.
360°
+45°
-45°
+45°
-45°
360°
J

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303