InSinkErator HWT-00 User manual

Tank Replacement | Instruction Sheet
Steaming Hot Water Taps
12345
STEP 1
PREPARATION
Unplug tank.
Run water from tank until cool. Turn off water supply.
Hot
(red)
12345
STEP
REMOVE LINE/TANK
Remove inlet tube. Remove outlet and
vent tubes from fittings.
23
1
2
Lift old tank off mounting
bracket or screws.
Drain water into empty
sink or container.
Hang new tank on mounting
bracket or screws.
MOUNT TANK
12345
STEP 3
FILL TANK & CONNECT POWER
If no leaks, plug in tank.Check for leaks around fittings.
Activate HOT handle
and hold until water flows
from the spout (1-2 min.)
To flush lines, run the water
for at least 2 min. (both hot
and cold handles if applicable).
Turn on water supply.
A
C
B
D
Hot
(red)
12345
STEP 5
Note: Gurgling or hissing is normal during initial heating cycle. Allow
12-15 minutes for water to reach desired temperature.
Note: Snap connect fitting not included.
Note: A minimal amount of water might spill when removing it
from the cabinet. Have a towel available for clean-up.
CONNECT LINE
Attach inlet tube.
Attach outlet and
vent tubes to fittings.
3
12
Inlet
(blue)
Outlet
(white)
6.4mm 8mm
11mm
Vent
(clear)
12345
STEP 4
Note: DO NOT plug in yet.
This appliance must be grounded. This steaming hot water tap is
equipped with a cord that has a grounding conductor and a grounding
pin. The plug must be connected to an appropriate outlet that is properly
installed and grounded in accordance with all local codes and ordinances.
DO NOT modify the plug provided with the appliance – if it will not fit the
outlet, have a proper outlet installed by a qualified electrician. Check with
a qualified electrician or serviceman if you are in doubt as to whether the
steaming hot water tap is properly grounded.
A steaming hot water tap, like any water heater, has a limited life and will
eventually fail. To avoid possible property damage and personal injury,
this steaming hot water tap should be regularly examined for leakage and/
or corrosion and replaced when necessary. A drain pan, plumbed to an
appropriate drain or outfitted with a leak detector, should be used in those
applications where any leakage could cause property damage. To check
for corrosion, examine the appearance of the dispensed water in a clear glass
once every three (3) months. If there is any discoloration or rusty appearance
unplug and drain unit. If the water discoloration remains after draining and
refilling unit, discontinue use and contact an authorized
InSinkErator service agent.
Electric Shock Hazard: Using an ungrounded or improperly connected
appliance can result in serious injury or death from electrical shock.
Personal Injury/Property Damage: This tank is a non-pressurized
tank. DO NOT modify this system. DO NOT close vent tube
or connect other type taps or valves to the tank. Use only the
InSinkErator tap. Use only parts provided. Contact an authorized
InSinkErator Service agent for repairs or replacement components.
Fire Hazard: To minimize possibility of fire, DO NOT store flammable
items such as rags, paper or aerosol cans near the tank. DO NOT
store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
Leak Hazard: Regularly inspect dispenser and plumbing fittings for
leaks, which can cause property damage and could result in
personal injury
•
• For your satisfaction and safety, read all instructions, cautions and
warnings before installing or using this steaming hot water tap.
• Make sure that all electrical wiring and connections conform to
local codes.
• A standard, earth (grounded) electrical outlet is required under the sink for
the tap’s electrical power.
• The wall outlet powering your tap must have electrical power supplied to
it continuously.
• This outlet must be fused and should not be controlled by the same
wall switch that operates the food waste disposer. Fuse/circuit breaker
required is 10 amp for 230 volt (10 amp for 220-240 volt UK) and 15 amp
for 120 volt.
• To ensure proper operation, this unit is not intended to be flushed with
chlorine. If you suspect elevated levels of chlorine in your water, it is
recommended to use our water filtration system.
• In Australia, all plumbing and electrical work must be completed by a
qualified tradesperson.
• To prevent damage or unit not operating properly, the water pressure
must be between 172 kPa - 862 kPa (1.7 bar - 8.6 bar; 25 psi - 125 psi).
Ambient (room) temperature between 10ºC and 38ºC. In Australia, an
Australian water mark approved 350 kPa set pressure limiting valve and
dual check valve must be used.
• Moving parts inside the tank causing a rattling noise is normal.
• If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a hazard.
WHAT YOU SHOULD KNOW BEFORE YOU BEGIN
PARTS INCLUDED
19mm Screws (2)
• DO NOT alter or remove the ground pin from power cord.
• Using an ungrounded appliance can result in serious injury or death
from electric shock.
• This appliance must be grounded – the power cord is equipped
with an equipment grounding conductor and a grounding pin. The
plug must be connected to an appropriate outlet, properly installed
and grounded in accordance with all local electrical codes and
ordinances.
Water must flow from faucet prior to plugging unit into electrical
outlet. DO NOT plug in yet.
NOTICE
Snap connect fitting not included. Required when
replacing tank manufactured prior to January 2006. Call
the AnswerLine® 1-800-558-5700 to order.
STOP
STOP
WARNING
WARNING
WARNING
WARNING
WARNING

PREPARATION
Turn off water supply.
TANK MUST BE MOUNTED LEVEL
TO ENSURE PROPER OPERATION.
Mount tank vertically within
400mm or less of faucet water
lines and within 760mm or less of
a standard grounded outlet.
Use a pencil to mark locations
for two hanging screws.
12345
STEP 1
CONNECT LINE
Attach inlet tube.
Attach outlet and
vent tubes to fittings.
3
12
Inlet
(blue)
Outet
(white)
Vent
(clear)
12345
STEP 3
6.4mm 8mm
11mm
Leave 6.4mm for
hanging tank
MOUNT TANK
Screws provided are for use in
wood only. Use wall anchors
(not supplied) for installation
into drywall.
Pre-drill 3mm pilot holes.
Install screws leaving
6.4mm exposed.
Hang tank on screws.
Tighten screws 1/2 turn
clockwise.
DO NOT overtighten screws.
12345
STEP 2
Hot
(red)
FILL TANK
Turn on water supply.
Activate the HOT handle
and hold it until water flows
from the spout
(approximately 1 to 2 minutes).
Run the water for at least
2 minutes to flush lines
(both the hot and cold handles
independently if applicable).
12345
STEP 4
HWTF (tank used with filter): 2-year warranty
HWTank (tank used without filter): 1-year warranty
HWT-1H: 1-year warranty
This warranty is provided by InSinkErator, a business unit of Emerson Electric
Co., (“InSinkErator” or “Manufacturer” or “we” or “our” or “us”) to the original
consumer owner of the InSinkErator product with which this warranty is provided (the
“InSinkErator Product”), and any subsequent owner of the residence in which the
Product was originally installed (“Customer” or “you” or “your”).
InSinkErator warrants to Customer that your InSinkErator Product will be free from
defects in materials and workmanship, subject to the exclusions described below, for
the “Warranty Period”, commencing on the later of: (a) the date your InSinkErator
Product is originally installed, (b) the date of purchase, or (c) the date of manufacture
as identified by your InSinkErator Product serial number. You will be required to show
written documentation supporting (a) or (b). If you are unable to provide documentation
supporting either (a) or (b), the Warranty Period commencement date will be determined
by Manufacturer, in its sole and absolute discretion, based upon your InSinkErator
Product serial number.
What is Covered
This warranty covers defects in materials or workmanship, subject to the exclusions
below, in InSinkErator Products used by a consumer Customer for residential use only,
and includes all replacement parts and labor costs. YOUR SOLE AND EXCLUSIVE
REMEDY UNDER THIS LIMITED WARRANTY SHALL BE LIMITED TO REPAIR OR
REPLACEMENT OF THE INSINKERATOR PRODUCT.
What is not Covered
This limited warranty does not extend to and expressly excludes:
• Losses or damages or the inability to operate your InSinkErator Product resulting
from conditions beyond the Manufacturer’s control including, without limitation,
accident, alteration, misuse, abuse, neglect, negligence (other than
Manufacturer’s), failure to install, maintain, assemble, or mount the InSinkErator
Product in accordance with Manufacturer’s instructions or local electrical and
plumbing codes.
• Wear and tear expected to occur during the normal course of use, including
without limitation, cosmetic rust, scratches, dents or comparable and reasonably
expected losses or damages.
In addition to the above exclusions, this warranty does not apply to InSinkErator
Products installed in a commercial or industrial application.
No Other Express Warranty Applies
This warranty is the sole and exclusive warranty provided to the Customer identified
above. No other express warranty, written or verbal, applies. No employee, agent,
dealer, or other person is authorized to alter this limited warranty or make any other
warranty on behalf of Manufacturer. The terms of this warranty shall not be modified by
the Manufacturer, the original owner, or their respective successors or assigns.
What we will do to Correct Problems
If your InSinkErator Product does not operate in accordance with the documentation
provided to you, or you have questions concerning your InSinkErator Product or how to
determine when service is needed, please see attached Service Agency List.
The following information must be provided as part of your warranty claim: your name,
address, phone number, your InSinkErator Product model and serial number, and if
necessary, upon request, written confirmation of either: (a) the date shown on your
installation receipt, or (b) the date shown on your purchase receipt.
Manufacturer or its authorized service representative will determine, in its sole and
absolute discretion, if your InSinkErator Product is covered under this warranty. You will
be given the contact information for your closest authorized InSinkErator Service Center.
Please contact your InSinkErator Service Center directly to receive in home warranty
repair or replacement service. Only an authorized InSinkErator service representative
may provide warranty service. InSinkErator is not responsible for warranty claims arising
from work performed on your InSinkErator Product by anyone other than an authorized
InSinkErator service representative.
If a covered claim is made during the Warranty Period, Manufacturer will, through its
authorized service representative, either repair or replace your InSinkErator Product.
Cost of replacement parts or a new InSinkErator Product, and cost of labor for repair
or installation of the replacement InSinkErator Product are provided at no cost to you.
Repair or replacement shall be determined by Manufacturer or its authorized service
representative in their sole discretion. All repair and replacement services will be
provided to you at your home. If Manufacturer determines that your InSinkErator Product
must be replaced rather than repaired, the warranty on the replacement InSinkErator
Product will be limited to the unexpired term remaining in the original Warranty Period.
Limitation of Liability
TO THE EXTENT PERMITTED BY LAW, IN NO EVENT SHALL MANUFACTURER OR
ITS AUTHORIZED SERVICE REPRESENTATIVES BE LIABLE FOR ANY INCIDENTAL,
SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, INCLUDING ANY ECONOMIC
LOSS, WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE OR
INABILITY TO USE THE INSINKERATOR PRODUCT OR THE MANUFACTURER’S OR
ITS AUTHORIZED SERVICE REPRESENTATIVE’S NEGLIGENCE. MANUFACTURER
SHALL NOT BE LIABLE FOR DAMAGES CAUSED BY DELAY IN PERFORMANCE AND
IN NO EVENT, REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF ACTION
(WHETHER BASED IN CONTRACT, INFRINGEMENT, NEGLIGENCE, STRICT LIABILITY,
OTHER SORT OR OTHERWISE), SHALL MANUFACTURER’S LIABILITY TO YOU
EXCEED THE PRICE PAID BY THE ORIGINAL OWNER FOR THE
INSINKERATOR PRODUCT.
The term “consequential damages” shall include, but not be limited to, loss of
anticipated profits, business interruption, loss of use or revenue, cost of capital or loss or
damage to property or equipment.
WARRANTY
CONNECT POWER
If no leaks, plug in tank.
Check for leaks around fittings.
12345
STEP 5
Note: Gurgling or hissing is normal during initial heating cycle. Allow
12-15 minutes for water to reach desired temperature.
Note: For tap installation, refer to “Installation” section in the Use and
Care manual included with the tap.
NEW Tank Installation | Instruction Sheet
Steaming Hot Water Taps
44666C Rev C
PARTS INCLUDED
19mm Screws (2)
• DO NOT alter or remove the ground pin from power cord.
• Using an ungrounded appliance can result in serious injury or death
from electric shock.
• This appliance must be grounded – the power cord is equipped
with an equipment grounding conductor and a grounding pin. The
plug must be connected to an appropriate outlet, properly installed
and grounded in accordance with all local electrical codes and
ordinances.
Water must flow from faucet prior to plugging unit into electrical
outlet. DO NOT plug in yet.
NOTICE
Personal Injurt/Property Damage: Tank must be located within
400mm of faucet and within 760mm or less of a standard grounded
outlet. DO NOT extend plumbing lines or use an extension cord set
with this unit.
Snap connect fitting not included. Required when
replacing tank manufactured prior to January 2006. Call
the AnswerLine® 1-800-558-5700 to order.
STOP
STOP
Note: Snap connect fitting not included.
WARNING
WARNING

Check out our full range of Kitchen Products
Kitchen Sinks
Stainless Steel Kitchen Sinks
Granite Composite Kitchen Sinks
Glass Kitchen Sinks
Ceramic Kitchen Sinks
Franke Kitchen Sinks
Kitchen Taps
Contemporary Kitchen Taps
Traditional Kitchen Taps
Franke Kitchen Taps
Pull out Rinser Kitchen Taps
Instant Boiling Water Taps
Insinkerator Waste Disposal Units