Intergraph ErgoAct OEM Monitor User manual

ErgoAct OEM Monitor
Installation Guide
February 1997
DHAF00720

Warranties and Liabilities
The information and the software discussed in this document are subject to change without notice and should not
be considered commitments by Intergraph Corporation. Intergraph Corporation assumes no responsibility for any
errors in this document.
The software discussed in this document is furnished under a license and may be used or copied only in accordance
with the terms of the license. No responsibility is assumed by Intergraph for the use or reliability of software on
equipment that is not supplied by Intergraph or its affiliated companies.
All warranties given by Intergraph Corporation about equipment or software are set forth in your purchase
contract, and nothing stated in, or implied by, this document or its contents shall be considered or deemed a
modification or amendment of such warranties.
Copyright
1997, Intergraph Corporation including this documentation, and any software and its file formats and audio-
visual displays described herein; all rights reserved; may only be used pursuant to the applicable software license
agreement; contains confidential and proprietary information of Intergraph and/or other third parties which is
protected by copyright, trade secret and trademark law and may not be provided or otherwise made available
without prior written authorization.
Restricted Rights Legend
Use, duplication, or disclosure by the United States Government is subject to restrictions as set forth in subdivision
(c)(1)(ii) of the rights in technical data and computer software clause at DFARS 252.227-7013.
Unpublished rights reserved under the copyright laws of the United States.
Intergraph Corporation
Huntsville AL 35894-0001
Trademarks
Intergraphand the Intergraph logo are registered trademarks of Intergraph Corporation. ErgoAct is a trademark
of Intergraph Corporation. Other brands and product names are trademarks of their respective owners.

Contents
Installing an OEM Monitor.........................................................................................1
Remove the Existing Monitor and Separator Plate.........................................................1
Set Up the Panasonic OEM Monitor..............................................................................1
Preparing the Monitor for Installation..............................................................2
Attaching the Separator Plate...........................................................................5
Set Up the Hitachi OEM Monitor ..................................................................................9
Removing the Swivel Base...............................................................................9
Attaching the Adapter Bracket.........................................................................9
Attaching the Separator Plate.........................................................................10
Install the OEM Monitor.............................................................................................13

1
Installing an OEM Monitor
This document explains how to remove existing monitors from the ErgoAct workstation stand, and to
install a Panasonic or Hitachi OEM monitor onto the workstation stand. Read the instructions in this
document before proceeding with the installation. To perform the installation, you will need the
following tools:
u No. 1 Phillips screwdriver
u No. 2 Phillips screwdriver
u No. 2 single slot screwdriver
u 3/16-inch Allen wrench
Remove the Existing Monitor and Separator Plate
The existing monitor on the workstation stand uses a separator plate to secure the monitor to the
stand. The separator plate (CFAB532E) must be removed from the existing monitor and installed
onto the new OEM monitor.
1. Turn off the power and disconnect the power cord from the existing monitor.
2. Remove and retain the screws that secure the monitor to the workstation stand. The screws are
located underneath the monitor at the back of the stand.
3. Slide the monitor off the stand and set it on its side.
WARNING Do not set the monitor on its display screen. Damage may result.
4. Remove and retain the shoulder screws that secure the separator plate to the monitor.
5. To install the new OEM monitor, refer to “Install the Panasonic OEM Monitor” or “Install the
Hitachi OEM Monitor.”
Set Up the Panasonic OEM Monitor
The hardware kit used to install the Panasonic monitor onto an ErgoAct stand contains the following
items:
u One monitor adapter bracket (MMSA408)
u Four shoulder screws (CFAB507)
u Two M6x12mm Phillips screws (CPHM044) (optional)
Before the monitor can be installed, it must be prepared for installation by removing the monitor
cover and swivel base, and attaching the adapter bracket included with the kit. Finally, the separator
plate from the previous monitor must be attached to the adapter bracket.

2
Preparing the Monitor for Installation
WARNING The monitor is heavy and could cause serious personal injury if dropped. Two persons are
required to lift and carry the monitor.
1. Unpack the monitor from its shipping carton.
2. Verify that the monitor power cord is supplied.
3. Remove the five screws from the back of the monitor cover as shown in the following figure.
Then, remove the monitor cover.
Screws (5)
Monitor
Cover
4. To access the swivel base, turn the monitor onto its side.
WARNING Do not set the monitor on its display screen. Damage may result.

3
5. Firmly press down and pull out the press tabs on the swivel base as shown in the following
figure.
Press Tabs
Swivel Base
6. Remove the swivel base from the monitor by sliding it to the back of the monitor.

4
7. Place the adapter bracket onto the bottom of monitor. Ensure the holding latches are secured
inside the slots in the monitor frame. Refer to the following figure.
Adapter
Bracket
Slot
8. Slide the bracket toward the front of the monitor to secure it in place. The bracket snaps in
without using screws.
9. Re-attach the monitor cover to the monitor and secure it with the screws removed in step 3.
Repeat these steps for the second monitor, if applicable.

5
Attaching the Separator Plate
The adapter plate is designed with mounting holes so that it can be used in single-monitor and dual-
monitor configurations. These holes are used to properly align the separator plate (CFAB532E) to
the adapter bracket. After the separator plate is installed, the monitor is set onto the workstation
stand. If the separator plate is not properly installed, the monitor cannot be secured to the stand.
Shoulder screws (included with the OEM monitor kit) attach the separator plate to the adapter
bracket. The separator plate is included with the workstation stand.
The following figure shows the mounting hole pattern for the adapter bracket, viewed as looking at
the bottom of the monitor.
R R
L L
R designates holes for the
monitor on the right side
of the stand, when facing
the front of the stand.
L designates holes for the
monitor on the left side of
the stand, when facing the
front of the stand.
R R
L L
Single Monitor
See the following instructions for single-monitor and dual-monitor configurations.

6
Single-Monitor Configuration
1. Install the four shoulder screws through the separator plate into the adapter bracket according to
the locations shown in the following figure.
Adapter
Bracket
Separator
Plate
2. Go to “Install the OEM Monitor” to complete the monitor installation. Use the screws removed
in “Remove the Existing Monitor and Separator Plate” when attaching the monitor to the
workstation stand.