International comfort products Cpfiltrk007a00 User manual

COMMERCIAL PACKAGED PRODUCT (2 - 5 TONS)

FILTER RACK PACKAGE

Part Number:

CPFILTRK007A00, CPFILTRK008A00 & CPFILTRK009A00

Installation Instructions

WARNING

ELECTRICAL SHOCK HAZARD

Failure to follow this warning could cause personal injury or death.

Electrical shock can cause injury or death.

Disconnect power supply and install lockout tag before attempting to

install accessory.

CAUTION

CUT HAZARD

Failure to follow this caution may result in personal injury.

Sheet metal parts may have sharp edges or burrs. Use care and

wear appropriate protective clothing and gloves when handling parts.

SAFETY CONSIDERATIONS

Installation and servicing of this equipment can be hazardous due

to mechanical and electrical components. Only trained and qualied

personnel should install, repair, or service this equipment.

Untrained personnel can perform basic maintenance functions such

as cleaning and replacing air lters. All other operations must be per-

formed by trained service personnel. When working on this equipment,

observe precautions in the literature, on tags, and labels attached to or

shipped with the unit and other safety precautions that may apply.

Follow all safety codes. Installation must be in compliance with

local and national building codes. Wear safety glasses, protective cloth-

ing, and work gloves. Have re extinguisher available.

Read these instructions thoroughly and follow all warnings or cau-

tions included in literature and attached to the unit.

Recognize safety information. This is the safety alert symbol .

When you see this symbol on the unit and in instructions or manuals, be

alert to the potential for personal injury. Understand these signal words:

DANGER, WARNING, and CAUTION. These words are used with

the safety alert symbol. DANGER identies the most serious hazards

which will result in severe personal injury or death. WARNING signi-

es hazards which could result in personal injury or death. CAUTION

is used to identify unsafe practices which may result in minor personal

injury or product and property damage. NOTE is used to highlight

suggestions which will result in enhanced installation, reliability, or

operation.

General

These lter racks can be used in either a horizontal or vertical

discharge application, and are designed to accommodate either 1” or 2”

(25.4mm or 50.8mm) wide lters. Use caution not to damage indoor

coil during installation.

Installation

1. Remove the lter access panel on the HVAC unit. (See Fig. 1.)

2. Install the top lter rack in the HVAC unit next to the indoor coil.

Lift rack to the very top of the return chamber and screw rack into coil

frame on both the left and right side. Be careful not to insert screws

where coil damage could occur. If using 2” (50.8mm) lters remove

lter spacer. (See Figs. 2A, 3A, and 4A.)

Fig. 1 - Filter Access Panel for

Accessory Filter Rack

Filter Accessory Panel

for Accessory Filter Rack

TABLE 1 - PACKAGE CONTENTS

Part No. Qty Description

CPFILTRK007A00

1 Top Filter Rack

1 Bottom Filter Rack

2 12 x 20 x 1in. (308.8 x 508 x 25.4mm) Filters

1 Hardware Bag

1 Instructions

CPFILTRK008A00

1 Top Filter Rack

1 Bottom Filter Rack

1 14 x 24 x 1in. (355.6 x 609.6 x 25.4mm) Filter

1 16 x 24 x 1in. (406.4 x 609.6 x 25.4mm) Filter

1 Hardware Bag

1 Instructions

CPFILTRK009A00

1 Top Filter Rack

1 Bottom Filter Rack

1 16 x 24 x 1in. (406.4 x 609.6 x 25.4mm) Filter

1 18 x 24 x 1in. (457.2 x 609.6 x 25.4mm) Filter

1 Hardware Bag

1 Instructions

NOTE: On top lter rack for small cabinet, screw left side to coil

frame. On right side, bend tab on rack and screw to unit divider. Hold

height dimension shown in Fig. 2.

3. Install the bottom lter rack in the HVAC unit next to the indoor coil.

Filter rack will rest on the HVAC base and screw into the left and right

side of the coil frame. Be careful not to insert screws where coil dam-

age could occur. If using 2” (50.8mm) lters remove lter spacer. (See

Fig. 2A, 3A and 4A.)

4. Install lters in rack. See Table 2 for sizes.

5. Replace lter access door on HVAC unit.

Manufacturer reserves the right to discontinue, or change at any time, specications or designs without notice and without incurring obligations

Fig. 2 - CPFILTRK007A00

Fig. 3 - CPFILTRK008A00 Fig. 4 - CPFILTRK009A00

Top Filter

Rack

Top Filter

Rack

Evaporating

Coil

Evaporating

Coil

Bottom Filter

Rack

Bottom Filter

Rack

*Unscrew spacer brackets on the top lter rack to t 2-in (50.8mm) lters

† Place 14 x 24 x 2in. (254.0 x 609.6 x 50.8mm) lter at the right side of the coil and 10 x 24 x 2in

(254.0 x 609.6 x 50.8mm) lters at the left side in this order.

**2-in. lters not included.

PART NO.* 1-IN. FILTERS SIZE 2-IN. FILTER SIZE**

CPFILTRK007A00 (2) 12 X 20 (304.8 X 508mm) (1) 10 x 20 (254 x 508mm)

(1) 12 x 20 (304.8 x 508mm)

CPFILTRK008A00 (1) 14 X 24 (355.6 X 609.6mm)

(1) 16 X 24 (406.4 X 609.6mm)

(1) 14 x 24 (355.6 x 609.6mm)

(1) 16 x 24 (406.4 x 609.6mm)

CPFILTRK009A00† (1) 16 X 24 (406.4 X 609.6mm)

(1) 18 X 24 (457.2 X 609.6mm)

(2) 10 x 24 (254.0 x 609.6mm)

(1) 14 x 24 (355.6 x 609.6mm)

Fig. 2A

Fig. 3A

Table 2 - Filter Sizes

Filter spacer

remove for 2”

lters

Filter spacer

remove for 2”

lters

Top Filter

Rack

Screw

Fig. 4A

Filter spacer

remove for 2”

lters

Top Filter

Rack

Screw

This manual suits for next models

Table of contents

Other International comfort products Air Conditioner manuals