Invue S3100v User manual

For technical assistance call

NA / LATAM // 704.752.6513 •888.55.INVUE

EMEA // +31.23.8900150

APAC // +852.3127.6811

S3100V Sensors & Stand

1Enrolling Sensors:

Locate the code on the sensor.

2Within the InVue LIVE app, use the

camera on your device to scan the

code and enroll the sensor. Fill out

the information for the sensor and

the device that will be displayed.

3Sensor Installation:

Place the adapter appropriate for

your xture onto the sensor. The

Product Availability hangbar

adapter is shown below.

4Plug the power connector on the

sensor into the device.

IMPORTANT! Do NOT remove

the red tab at this time!

5Ensure that the sensor sits

squarely on the device. 6While holding the sensor in place

with one hand, pull the red tab to

expose the adhesives.

7Peel the clear lm from the

adhesive. 8Stand Installation:

To install the stand, begin by using

the provided alcohol wipe to clean

the area where the stand will be

placed. Allow it to dry completely.

For technical assistance call

NA / LATAM // 704.752.6513 •888.55.INVUE

EMEA // +31.23.8900150

APAC // +852.3127.6811

S3100V Sensors & Stand

9Peel the clear lm from the 2

adhesives on the bottom of the

stand.

10 Place the stand where desired,

with the logo facing away from

the customer position, and apply

pressure for at lest 10 seconds.

11 Plug the power cable into a PS515

power supply. Plug the power

supply into a power outlet.

12 Place the sensor and device into

the stand. The gold LED on the

sensor will illuminate to indicate

that it is receiving power.

For technical assistance call

NA / LATAM // 704.752.6513 •888.55.INVUE

EMEA // +31.23.8900150

APAC // +852.3127.6811

S3100V Sensors & Stand

LIVE Vertical Wireless

Model: VRTWRLSS

Hereby, InVue Security Products, Inc. declares that the radio equipment type VRTWRLSS is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:

https://invue.com/product-compliance/

EU Importer:

INVUE SECURITY PRODUCTS B.V.

Saturnusstraat 17 D

2132 HB Hoofddorp

The Netherlands

+31 23.8900150

Manufacturer:

InVue Security Products, Inc.

9201 Baybrook Lane

Charlotte, NC 28277, USA

Maximum output power is 5.2V. Operation is limited to the following channels/bands as supported in the country of use: 863-870MHz, 902-927MHz

Accessories and Software to operate as intended:

Zone Manager 30 (DBD702) and Zone Manager 52 (DBD701) establish wireless display security and has two alarm settings that are activated when a sensor enters an Alarm Zone, or when it exits a Secure Zone. Software version: FW0219_2021-01-05_810_0_x.

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

operation.

Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

ISED Regulatory Compliance

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions

suivantes :

(1) L’appareil ne doit pas produire de brouillage;