IPOX OF01-AS20KM User manual

Please follow below the installation steps
Check the following items before installation(in pair), if any missing, please contact the dealer .
Optical Fiber Transmitter 1 pcs
Optical Fiber Receiver 1 pcs
Power Adaptor 2 pcs
Hangers 4 pcs
User Manual 1 pcs
1)P
power on will damage the device;
2) Please check if the network cable and other transmission cables are occupied by other device;
3) Use a network cable to connect with optical fiber transceiver's LAN port and NVR or computer,
etc.;
4) Use one single mode single optical fiber to connect with two optical ports of the optical fiber
transceiver. One end of the fiber should connect with optical transceiver's TX port, the other end
should connect with the RX port;
5) Check if the installation is correct and device is good, make sure all the connection is reliable
and power for the system;
6) Make sure the network is normal.
lease turn off the signal power and the device's power before installation, installation with
Optical Fiber Transceiver is a fast Ethernet optical fiber transmission equipment, which can
achieve different transmission mediums transformation over network cable and fiber and
support 10/100Mbps network bandwidth. The product can be used in pairs, including
transmitter and receiver. It is widely used in security surveillance system and Ethernet fiber-
to-the-home occasion, etc.
Feature
Provide 100Mbps 1 optical fiber port and1 Ethernet port, which can achieve the data
transformation between optical fiber and Ethernet;
Support 1X9 optical module and SC port, use single mode single fiber that the transmission
distance can up to 20km;
Compatible with IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX/FX Ethernet standards;
Support 10/100Mbps full/half Duplex automatic adaptation, support automatic MDI/MDIX;
Power adaptor uses aerial socket, improves the performance and stability;
Dynamic LED indicator light achieve real-time display of the equipment current working
condition, provides simple working condition indicator and troubleshooting;
Compact aluminum shell design, easy for desktop and wall-mounted installation.
effectively
Optical Fiber Transceiver
User Manual
Notice
12
Please note that 2 optical fibers should cross connect with two optical fiber ports of the
transceiver.
VerB 1.1
Board Diagram
Optical Fiber Transceiver
1) Power is power indicator; FED, SD, LINK is optical fiber port indicator, they mean:
Link: indicate optical port connection status, On: connection ok; Off: connection failed;
Flash: connection ok and has data switch.
SD: optical port signal detection, On: optical fiber connection right; Off: without optical
fiber connection.
FED: remote failure mode receive, On: 80ms Off: 20ms Always off: no receive.
2) LED failure indication function, please refer to the below table:
Description:
Right Board
Ethernet LED
Optical Port
Link
Optical Port
SD
Optical Port
FED
Status
On
On
On
Off
Connection ok
Flash
Flash
On
Off
Connection ok and has data switch
Off
Off
On
Off
Remote Ethernet port can not connect
Off
Off
Off
Off
Fiber RX off line, fiber TX/RX offline
TX/RXdropped
Off
Off
On
Flash
Fiber TX off line
Optical
port
Power and optical
indicator light
POWER
Power input
5V DC
Fiber
SD
FED
Lin k
Pow er
SD
FED
Lin k
Ethernet port
Left Board
Application
IP Camera
Optical Fiber Transceiver
Ethernet Switch
Network Cable
Optical Fiber Transceiver
Fiber
Network Cable
Installation steps

连接接 口
Specification
连接接 口
Item
Description
Power
Power Supply
Power Adapter
Voltage Range
DC5V
Power Consumption
＜5W
Ethernet Port
Ethernet Port
LAN Port:10/100Mbps
TransmissionDistance
LAN Port: 0～100m
Optical Port
Optical Port
Single Fiber SC Port
Wave Length
Transmitter:1310nm/1550nm
Receiver:1550nm/1310nm
Bandwidth
155Mbps
Ttransmission Distance
Single Mode Fiber:20km; Mutil-mode Fiber:2km
Network Switch
Ethernet Standard
IEEE802.3 10BASE-T, IEEE802.3u 100BASE-TX/FX
Status Indicator
Power Light
1 (Green)
Ethernet Indicator Light
RJ 45 Port 1(Green)
Optical Indicator Light
FED, SD, LINK 3 (Green)
Protection
ESD
1a Contact Discharge 3 level 6KV
1b Air Discharge 3 level 8KV
Per:IEC61000-4-2
Working
Environment
Working Temperature
0 ~55℃℃
Storage Temperature
-40 ~75℃℃
Humidity(Non-condensing)
0~95%
Mechanical
Dimension(L*W*H)
83mm×90mm×25mm
Material
Aluminium
Color
Black
Weight
100g
连接接 口
Trouble Shooting
Please follow the steps if the equipment has trouble.
Make sure the equipment is installed according to the manufactures installation guide;
Please confirm if the RJ45 cable order is in accordance with EIA/TIA568A or 568B
standards;
The maximum transmission distance depends on the quality of signal source and
transmission cable, Please do not exceed the device's maximum transmission distance;
Replace the equipment that can not work with a proper functioning optical fiber
transceiver to check if the equipment is damaged;
Please contact your vendor if trouble still exists.
Optical Fiber Transceiver
34
Optical Fiber Transceiver
Instruments to be used: wire crimper, network tester, Wire sequence of RJ45 plug should
conform with EIA/TIA568A or 568B standards.
1) Please remove 2cm long the insulating layer and bare the 4 pairs UTP cable;
2) Separate the 4 pairs UTP cable and straighten them;
3) Line up the 8 pieces of cables per EIA/TIA 568A or 568B;
4) Cut off the cables to leave 1.5cm bare wire;
5) Plug 8 cables into RJ45 plug, make sure each cable is in each pin;
6) Use the wire crimper to crimp it;
7) Repeat above 5 steps to make the another end;
8) Use network tester to test the cable whether it works.
RJ45 Making Method
Pin Color
White/Green
Green
Blue
White/Orange
White/Blue
White/Brown
Orange
Brown
1
2
3
4
5
6
7
8
Pin Color
1
2
3
4
5
6
7
8
White/Green
Green
Blue
White/Orange
White/Blue
White/Brown
Orange
Brown
EIA/TIA 568A EIA/TIA 568B
Notice
When choose RJ45 make sure if one end is EIA/TIA568A,the other end should also be EIA/TIA568A.
When choose RJ45 make sure if one end is EIA/TIA568B,the other end should also be EIA/TIA568B.
Specification change will not be noticed