iROCKER NAUTICAL KIDS User manual

INFLATING & DEFLATING ..........................................................
INSTALLING FINS .....................................................................
SAFETY GUIDELINES ..................................................................
FOLDING & STORAGE ...............................................................
THE ACTION MOUNT .................................................................
ADJUSTABLE KIDS PADDLE ..........................................................
TRANSPORTING YOUR BOARD .................................................
CARE & MAINTENANCE ............................................................
REPAIRING YOUR BOARD ..........................................................
WARRANTY INFORMATION .......................................................
RELEASE OF LIABILITY ................................................................
2
3
4
5
6
6
7
8
9
10
11
CONTENTS
1

INFLATING & DEFLATING
INFLATING YOUR BOARD
Generally, the air pump’s pressure gauge will start to register a reading
after about 150 pumps (approx. 7 PSI). It should take about 250 pumps
to achieve 15 PSI.
TO INFLATE:
Attach the hose to the air pump.
Locate the air valve on the tail section of the board and open the
air valve cap.
Before connecting the hose to the board, make sure the air valve
is in the CLOSED/UP position.
Connect the hose to the board by pressing down and twisting
clockwise. Once connected, set the pump to SETTING 1 and begin
inflating.
(NOTE: The pump’s pressure gauge will not register a
reading until the board reaches 7 PSI.)
Midway through inflation, when operating the air pump becomes
more difficult, set the pump to SETTING 2, then continue
inflating.
When nearing full inflation, set the air pump to SETTING 3 and
fill to 15 PSI.
Once the board is fully inflated, disconnect the hose from the air
valve by twisting it counterclockwise. It is normal to hear a small
amount of air escape when removing the hose.
AIR VALVE CAP CLOSED/UP POSITION OPEN/DOWN POSITION
2

TO INSTALL:
DEFLATING YOUR BOARD
IMPORTANT: The valve wrench is for repairing valve leaks and should
never be used for deflation.
OPEN/UP POSITION PROPERLY INSERTEDALIGNED WITH NOTCH CLOSED/DOWN POSITION
Make sure the air valve is DRY.
Press firmly on the pressure release pin for 2 seconds, then twist
clockwise to lock into the OPEN/DOWN position.
Be prepared for a loud rush of air when opening the air valve.
Allow air to escape from the board for a few minutes before
folding.
2 +1 FIN CONFIGURATION
Your NAUTICAL Kids board comes equipped
with three removeable flip-lock nylon fins for
added maneuverability and control.
Make sure the fin box lock is in the OPEN/UP position.
Insert the front of the fin into the notched section of the fin box.
Rock the fin back and down until it’s in place, then set the lock
lever to the CLOSED/DOWN position.
Confirm each fin is securely attached before paddling.
TO DEFLATE:
INSTALLING YOUR FINS
3

FOLLOW LOCAL BOATING LAWS
IMPORTANT: Remember to check local laws and regulations regarding
the safe and proper use of this product. Always paddle with a U.S. Coast
Guard approved personal flotation device (PFD).
Never go paddleboarding in severe weather or water conditions that
might inhibit your ability to steer the board or return to shore safely.
Don’t paddle before dawn, after sunset, or in any other poor lighting
conditions that might impair visiblity.
Minors should always use this product with adult supervision.
Never use this product beyond your own skills or ability.
SAFETY FIRST!
4

5
FOLDING YOUR BOARD
IMPORTANT: Dry the board completely before tightly folding for storage.
Excess moisture may cause mildew or mold damage.
When folding the board, always start at the nose, making sure the air
valve is in the OPEN/DOWN position. Once the board is completely
folded, set the air valve to the CLOSED/UP position, then wrap the strap
around the rolled board and place it in the bag.
TO FOLD:
Once the board is completely dry and fully deflated, lay it
deck-side up on a flat surface.
Begin folding the board tightly in sections, starting from
the nose.
Continue folding until the board is completely rolled up,
then set the air valve to the CLOSED/UP position.
IMPORTANT: Avoid standing the rolled board on its side on rough
surfaces such as concrete or rocks. This can cause damage to the first
layer of the rail.
FOLDING & STORING YOUR BOARD

ATTACHING ACCESSORIES
Your board has a built-in ACTION MOUNT with M8 size thread, allowing
you to customize your board with a variety of accessories. Be sure to
ATTACH YOUR ACCESSORY AFTER INFLATING and remember to
REMOVE IT BEFORE DEFLATING.
TO OPEN: Grab the notched sides of the C-clamp,
firmly pulling it towards you.
TO CLOSE: Once the paddle is at the desired length,
apply gentle thumb pressure, pressing the
C-clamp shut. Be careful not to pinch your
fingers when adjusting paddle length!
IMPORTANT: DO NOT REMOVE SHAFT STYROFOAM
Your board comes with a 3-piece paddle designed specifically for
shorter riders. DO NOT REMOVE any styrofoam from the paddle shaft,
as it provides buoyancy and allows the paddle to float.
Always disassemble and rinse your paddle with fresh water after each
use and allow it to dry before reassembling.
THE ACTION MOUNT
KIDS SUP PADDLE
6
ACCESSORY MOUNT

7
IMPORTANT: Do not transport your board while inflated. Your board
is designed to be compact for convenient storage and travel. Never
transport an inflated paddle board on top of a vehicle. Due to lack
of weight when inflated, the board will travel poorly if strapped to the
roof of a moving vehicle. Damages or warping incurred by improper
transport are not covered by warranty.
When transporting the board, be sure to avoid sharp objects.
Punctures are not covered by warranty.
Keep the board clear of any heat-producing items such as camp
stoves, gas lamps, etc. Damages resulting from heat are not covered
by warranty.
TRANSPORTING YOUR BOARD

RECOMMENDED BOARD PRESSURE: 15 PSI
Your board can hold up to 25 PSI. However, the recommendation is
15 PSI as the board will remain rigid at 15 PSI and no benefit is gained
by inflating further.
If the board is inflated cold to 25 PSI and then placed in direct sunlight,
the heat will increase the pressure, causing potential overinflation and
damage to the board’s seams. This damage is not covered by warranty.
AIR PUMP MAINTENANCE
Regularly clean the air filter located under the pressure gauge. (The
gauge unscrews from the top by hand.) Over time, the pump may
naturally lose lubrication and you may need to reapply more lubricant.
We recommend using white lithium grease. To lubricate:
Never leave your paddleboard exposed to direct sunlight when out
of the water. Always store your paddleboard in the shade when
not in use. If you must expose your board to direct sunlight during
transport or temporary storage, it is safest to keep the bottom facing
up. Prolonged exposure to the sun, even while paddleboarding, may
impact the integrity of the board materials. Damage resulting from
heat is not covered by the manufacturer’s warranty.
Open the top cap of the pump and pull out the plunger.
Spread a thin layer of lubricant on the black gasket on the bottom
of the plunger, then reassemble the pump.
TO LUBRICATE:
CARE & MAINTENANCE
8
IMPORTANT: PROLONGED HEAT EXPOSURE

9
EMERGENCY REPAIR KIT
This board comes with an emergency repair kit that includes a
valve wrench and repair patches for small leaks and/or tears.
Repair glue is not included for shipping reasons but can be found
on our website.
For best results, use the PVC adhesive found on our website. This
waterproof adhesive is recommended over other commercial glues.
BOARD MAINTENANCE
Sun, sand, and saltwater will degrade any manmade material over
time. Rinse off sand and saltwater deposits from your paddleboard
with fresh water, then wash with soap and water and store in a cool,
dry environment after each use. Allow carry handles to dry completely
prior to storing for a prolonged period.
TO REPAIR:
Completely deflate the paddleboard.
Thoroughly clean the surface around the leak and the matte-finish
side of the repair patch with rubbing alcohol. Both surfaces must be
free of moisture, oil, and debris.
Apply repair glue (not included) carefully and evenly to both the
paddleboard surface and the entire matte-finish side of the repair
patch.
Best practice is to seal the patch to the board using a clamp, leaving
the clamp in place for 12-24 hours.
Allow repair glue to dry for at least 24 hours before using your
paddleboard.
Always test your board in shallow water after any repair.
REPAIRING YOUR BOARD

UPON RECEIVING YOUR NEW BOARD, PLEASE INSPECT IT THOROUGHLY
AND REPORT ANY MANUFACTURING DEFECTS.
When purchased new, all NAUTICAL boards come with a 2-YEAR limited warranty. In order to receive
warranty service, you must be able to provide proof of purchase. The 2-year warranty period begins at
the date of shipment. All warranty claims must be submitted via email to [e-mail] with
your order number. See below for warranty submission steps.
The buyer is responsible for return shipping for any warranty claim. After inspection of any product
found to be defective, iROCKER will either repair or replace the defective part or item as deemed
necessary by iROCKER.
Never use this product in a way that modifies the structure of the product or contradicts the information
found in your owner’s manual.
For a copy of our full warranty policy, and for important warranty and liability information, please refer
to our website:
www.irockersup.com
HOW TO SUBMIT A WARRANTY CLAIM:
Please allow 5-7 business days for our Customer Experience Team to respond. Make sure to make a note
of your TICKET NUMBER for easy reference. Please discontinue using your NAUTICAL Kids board until our
Customer Experience Team has resolved your warranty issue.
Review the warranty policy above to ensure you have a qualifying claim.
Take a picture and/or video documenting the issue.
Take a picture of the serial number located near the fin boxes.
E-mail [e-mail] with subject line “For Warranty Evaluation” and include
your pictures and/or video, serial number, order number, and proof of purchase in the
body of your e-mail.
10

11
RELEASE OF LIABILITY
By assembling and using this product (“Product”), you agree that you have read and understand the entire
Product owner’s manual and the on-product warnings and labels, including all instructions and warnings
contained in these materials, prior to using the Product, and that copies of such warnings, labels and
instructions have been made available to you. By assembling and using this product, you are also agreeing
to the terms of this Release of Liability (this “Release”). You agree to wear all recommended protective
apparel and to use the Product only according to the instructions provided in the instruction manual and the
on-product warnings and labels. You agree not to use the Product under the influence of alcohol, drugs, or
anything that could impair your faculties and/or judgment and that you do not have any physical or mental
disabilities that may interfere with your use of the Product. You additionally agree that you will ensure any
additional or subsequent users of the Product will read and understand the entire instruction manual, the
on-product warnings and labels, and this Release. Misuse or improper use of the Product could result in
risks, dangers, and hazards which may result in serious injury or death.
BY USING THE PRODUCT, YOU ACKNOWLEDGE AND UNDERSTAND THAT THE ACTIVITY FOR WHICH
THE PRODUCT IS DESIGNED IS A POTENTIALLY DANGEROUS ACTIVITY AND INVOLVES THE RISK OF
SERIOUS INJURY, DISABILITY, AND EVEN DEATH. BY USING THE PRODUCT, YOU ACKNOWLEDGE THAT
YOU ARE VOLUNTARILY PARTICIPATING IN THE ACTIVITY FOR WHICH THE PRODUCT IS INTENDED
AND AGREE TO ACCEPT AND ASSUME ANY AND ALL KNOWN AND UNKNOWN RISKS OF INJURY,
DISABILITY AND EVEN DEATH ARISING FROM YOUR PARTICIPATION, INCLUDING THOSE RISKS
CAUSED BY ACTIONS OR NEGLIGENCE OF RELEASEES AND/OR ANY DESIGN, MANUFACTURING OR
ASSEMBLY DEFECTS IN THE PRODUCT.
To read the full Release of Liability, visit:
www.irockersup.com/release-of-liability