iTrac VT1000 User manual

VT1000 USER MANUAL
1
GPS
Vehicle
Tracker
User Manual
V1.1
VT1000

VT1000 USER MANUAL
2
Preface
Thank you for purchasing our products. This deliberately edited manual is
to introduce the tracker with the complete technical data and the instructions
showing how to operate the device smoothly and correctly. Make sure to read
this manual carefully before using this product. Most problems could be solved
through the explanations and the troubleshooting tips. Once you finish reading
it, keep it handy for necessary reference. Please note that specification and
information are subject to changes without prior notice in this manual. Any
change will be integrated in the latest release. The manufacturer assumes no
responsibility for any errors or omissions in this document.
Content
Ⅰ. Preface…………………………………………... 2
Ⅱ. Attentions……………………………………….. 3
ⅢHardware description…..…………………….… 3
Ⅳ. Main function……………………………….….. 3
Ⅴ. Set up………………………………………...….. 4
Ⅵ. Installation diagram………………………...….. 7
Ⅶ. Installation……………………………….….…... 7
Ⅷ.Track by 900D web based tracking software………..…12
Ⅸ. Application…………………………………….… 15
Ⅹ. Specs………………………………....…………….15
Command set………………………………………16

VT1000 USER MANUAL
3
Attention
1. Make sure to read this manual carefully before using this product.
2. Please insert the SIM card before installing, and make sure the SIM card has no password, otherwise the
tracker will not work normally.
3. Please make sure that all the cables of the tracker has been connected rightly, and then connect the tracker to
host power. Must not install or take down the tracker when it is power on. If you found any troubles or
omissions about the connections of cables, please cut off power first, otherwise you will easily damage the
tracker.
4. The tracker works in wireless communications, so please cut off the host power before your vehicles entering
fuel depot and dangerous material place.
5. The tracker’s work voltage is 9V-30V. Please use the tracker in the scope of work voltage.
6. The host of GPS tracker is a low-power wireless transmitter and receiver. It receives and sends radio
frequency signal when it is working.
7. To avoid electromagnetic interference or uncompatible configuration, please stop using your tracker in the
noticed place.
GPS Vehicle Tracker
◆Hardware Description
1. Host Tracker
2. Start up
Put the SIM card in place and installed the tracker in the car, the red indicator is on. About 40 seconds, the
unit will begin to work and acquire the GSM signals as well as the GPS signals, and the red indicator will keep
flashing every 2 seconds when the GSM module is no communication. When the blue indicator is light, the unit
has been located.
◆Main functions
1. Positioning and Tracking: Through the on-line Positioning Platform or the cell phone to locates at times, and
get the working status. You can choose the Positioning Platform by yourself.
2. Triggering Emergency Alarm: When there is a emergency happened on the vehicle, you can put on the button
and the installed unit will send out alarm to the authorized numbers.
3. Remote controlling oil and circuit: you can control the oil and circuit via the unit by SMS in anywhere and
anytime.
4. Remote Monitoring: In anywhere and anytime, call the phone number in the unit, when it connects, you can
monitor the sound around 5 meter.

VT1000 USER MANUAL
4
5. Movement Alert: Send SMS to the unit to start the movement alert function. When the vehicle is moving, the
unit will send the movement alert to all authorized numbers.
6. Overspeed Alert: Send SMS to the unit to start the movement alert function. When the vehicle is overspeed,
the unit will send the overspeed alert to all authorized numbers.
7. Geo-fence: Set up a geo-fence for the unit to restrict its movements within a district. The unit will send the
message to all authorized numbers when it breaches the district.
8. Restart the unit: send SMS to resume the default of unit.
9. Auto Track: You can set up auto track by SMS or on-line positioning platform.
10. Mileage statistics; ACC checking; cutting off power and alarm.
11. Compatible with the original anti-theft alarm: It will send SMS alarm after the original anti-theft alarm
warning.
﹡Modify the IP and Port of Communication Protocol for different on-line positioning platform
◆Set up
2. Add authorized number (Can set 5 authorized number)
Send “admin+password+space+authorized number”
Example:Send SMS “admin123456 13612345678”."admin" is instruction, "123456" is password,
"13612345678" is authorized number. It will reply “admin ok!”. You can set 5 authorized phone number
Maximum.
3. Delete authorized number
Send “noadmin+password+space+authorized number”
Example:Send SMS “noadmin123456 13612345678”."noadmin" is instruction, "123456" is password,
"13612345678" is authorized number. It will reply “noadmin ok!”.
Send SMS “requestdeleteadmin” deleted all authorized number.
4. Change the Password
Send SMS: “password+old password+space+new password” to change the password.
Example: Send SMS “password123456 138138”. "password" is instruction, "123456"is old password,
"138138" is new password. Password must be six digits. Tracker’s initial password is 123456.
5. Resume the initial password
If you forget your password, you can resume the initial password 123456.
Send “resumepassword”to the tracker, the tracker will resume the initial password. If there is no authorized
numbers, all numbers can resume initial password. If there is already authorized numbers, only the authorized
numbers can resume initial password.
6. Control Oil
Send SMS “stopoil+password” to control oil. For example send SMS: stopoil123456
"stopoil" as instruction, "123456"as password.
To supply the oil again, send SMS “supplyoil+password” to the unit. For example, send

VT1000 USER MANUAL
5
SMS “Supplyoil123456” to the tracker. "Supplyoil" as instruction, "123456" as the password.
7. Control Circuit
Send SMS “stopelec+password” to control circuit. For example send SMS: “stopelec123456”.
"stopoil" as instructions, "123456" as the password.
To supply the circuit again, send SMS “supplyelec+password” to the unit. For example, send
SMS “Supplyelec123456” to the tracker. "supplyelec" as instruction, "123456" as password.
8. Switch between “tracker” and “monitor”
Send SMS “tracker+password” to the unit, it will reply “tracker ok!”. For example send SMS “tracker123456”.
In this mode, you can get position SMS by call tracker. Default :tracker
Send SMS “monitor+password” to the unit, and it will reply “monitor ok!” and switch to “monitor” mode. For
example send SMS: “monitor123456”. In this mode, you can monitor tracker by call tracker card number.
9. “Monitor”
There are three modes for monitor.
1) All Monitor Mode: Send SMS “allmonitor”to the unit, the unit will return to this mode. In this mode, any
number can monitor this unit.
2) Restrict Monitor Mode: Send SMS “restrictmonitor”to the unit, the unit will return to this mode. In this
mode, authorized number can monitor this unit.
3) Close Monitor Mode: Send SMS “closemonitor”to the unit, the unit will return to this mode. In this mode, all
numbers can not monitor this unit.
10. Movement alert
Set up: The user can send SMS “move+password” to the unit, then the unit will reply “move ok!” .In case of
such a movement, it will send SMS “move+Geo-info” to the number.
For example, send SMS “move123456” to the unit. "move" as instructions, “123456”as password.
Cancel: Send SMS “nomove+password” to deactivate the movement alert.
Default radius is 200 meters, if GPS tracker moves out this radius, then it will send SMS alert.
11. Overspeed alert
Set up: Send SMS “speed+password+space+080” to the unit (support the speed is 80km/h).
Example, send SMS “speed123456 080”. "speed" as instruction, "080" as limit speed, “123456”as password.
Cancel: Send SMS “nospeed+password” to deactivate the overspeed alert.
12. Geo-fence
Set up a geo-fence for the unit to restrict its movements within a district. The unit will send the message to the
authorized numbers when it breaches the district.
Set up: The user can Send SMS “stockade+password+space+MinLatitude,MinLongitude;MaxLatitude,
MaxLongitude” to unit to set the restricted district. In case of breach, it will send SMS “stockade! + geo-info” to
the authorized numbers.
For example send SMS “stockade123456 22.548123,114.081234;22.549123,114.082234” to the unit.
Remark: The first latitude & longitude is coordinate of min of the Geo-fence, while the second latitude &
longitude is the coordinate of the max. It will alarm one time in each setting.
Cancel: Send SMS “nostockade+password” to deactivate this function.

VT1000 USER MANUAL
6
This function will be out of effect after the unit moves outside the district.
13 . Restart the tracker.
Send SMS “reboot+password” to the tracker. For example“reboot123456”.The tracker will be restarted. It will
reply “system will reboot...”.
14. Enquiry Positioning
Send SMS “position” to the unit, then the unit will send SMS with real-time longitude and latitude to the cell
phone.
If you have set authorized phone number, then GPS tracker will only send message to authorized phone number.
If you do not set authorized phone number, then it can reply to any number.
15. Modes switch between “telephone” and “web”
Set up: Send SMS “web+password” to device. For example, the password is 123456. Send SMS “web123456”
to the device, the device will reply SMS “set web ok”. After this, the tracker will report the GPS data to IP
address. Default :web
If you want to send GPS data to telephone, you can send SMS “telephone+password” to device, the device will
reply “set telephone ok”. And then, the device will send GPS data to your telephone by SMS.
Relations diagram:
16. Modify IP address and port
The IP address and port of the tracker can be modified and transferred data to other platform. Send SMS “ip+
ip address+port+port value” to the unit. If the platform’s IP address and port is 58.64.200.196 and 7000,
send SMS “ip58.64.200.196port7000” to the tracker. It will reply “set IP address and PORT ok.”. After this,
device will send GPS data to this IP and Port.Default ip:58.64.200.196 port:7000
17. Set APN
Case 1 (No apn user name and apn password)
In order to send GPS data to IP address, you still must set mobile network Access Point Name (APN). If you
don’t know the APN, you can consult local network service supplier. The format of set APN is “apn+password
+space+apn name”. For example you send SMS “apn123456 cmnet” to the device. The device will reply SMS
“Set APN ok.” Default APN:cmnet
Case 2 (Need apn user name and apn password)
1.Send SMS “apn+password +space+apn name”

VT1000 USER MANUAL
7
Example:apn123456 cmnet
2.Send SMS “user+space+apn user name+space+apn password”
Example: user telecom abc1234
“user” is command, “telecom” is APN user name, “abc1234” is APN password. After send SMS, tracker will
reply “Set GPRS User and Password ok . ” .
18. Set country time zone
In the default, tracker reply position SMS time is UTC time. After you can set zone time, tracker will reply the
time of your country. The format is “zone+password+space+time zone value”. For example, “zone123456 8” is
set east 8 time zone. Time zone value ranges from -12 to 12. One time zone stands for one hour. “zone123456
-8” is set west 8 time zone. After send SMS, tracker will reply “Set Time Zone OK.”.Default time zone: 0
19. Set ACC open and close send data interval
You can set the interval of send data when ACC open and close. The format of set ACC open interval is
“accon+time interval”. For example “accon 007” stand for when ACC open send data for every 7 seconds.
Default : 30 seconds
The format of set ACC close interval is “accoff+time interval”. For example “accoff 180” stand for when
ACC close send data for every 180 seconds. Default : 60 seconds.
20. Set ACC open and close send SMS notify
You can set the SMS notify of when ACC on and off. The format of set is “accnotify+1 or 0”. For example
“accnotify1” stand for when ACC on and off send SMS to authorized numbers. “accnotify0” stand for close send
SMS notify. In order to use this function, you must set authorized numbers.
21. Get GPS Info with Google Format
You can get latitude and longitude with Google website format. So you can open map directly by mobile. The
format of SMS is “google”. After you send SMS, tracker will reply GPS info with google website format.
22. Set call reply SMS format
You can set reply SMS format after you call tracker. The format of SMS is “geosms+1 or 2”.
Example:“geosms1” set reply SMS format as “position”. “geosms2” set reply SMS format as “google”.
◆Installation diagram of The Tracker

VT1000 USER MANUAL
8
◆GPS Vehicle Tracker Installation
GPS tracker should be installed by technical professional of local service centre. Without permission, the user
cann’t repair and move the tracker randomly. If users do, any unfortunated damage should be compensated by
himself.
Installation steps (caution: the following installation should under no power, otherwise will be dangerous)
1.Power supply line: The red wire connects 12V“+”;Black wire connects to GND“-”
2.Connection shock sensor.(Orange Wire)
3. Wire for cutting off oil of the tracker(Yellow Wire)
Yellow wire connects the relay pin 86; 85 pin connect to 12 V DC , 87a pin and 30 pin in series power supply
circuits. Caution: Wrong connection of yellow wire will damage the tracker.
4. Wire for cutting off circuit of the tracker(White Wire)
White wire connects relay pin 86; 85 pin to 12 V DC, 87a pin and 30 pin are in series power supply circuits.
Caution: Wrong connection of yellow wire will damage the tracker.
5. Emergency triggering (SOS) alarm (Blue Wire)
The blue wire connects the positive of the alarm button, and the black wire connects the negative of the alarm
button.
6. Vehicle door detect, low level trigger (Gray Wire)
The Gray wire connects with Door sensor.

VT1000 USER MANUAL
9
b. --
Picture b. Door sensor Connect and state diagram (Door closed/Open)
7.Purple Wire (Temperature)
Connection temperature sensor
8.Brown Wire/Black Gray Wire
Connection fuel sensor.
Fuel sensor Installation Guide：
Connect Fuel sensor with GPS Tracker. Connect External Power DC12V Or 24V .Turn on GPS Tracker.
Wait till the GSM signal is ok. （The red LED Flash Slow）
(1) Inquiry the current R_MAX value：
Move the black float to the position a (refer to image 1).
Send SMS: readr****** to the GPS Tracker,(****** is password, default 123456).
Example: readr123456
The GPS Tracker will reply: The current_R_value :XXX (XXX is 3 digits).
Example: The current_R_value : 160
(2) Inquiry the current R_MIN value.
Move the black float to the position b (refer to image 2).
Send SMS: readr****** to the GPS Tracker,(****** is password, default 123456).
Example: readr123456
The GPS Tracker will reply: The current_R_value :XXX (XXX is 3 digits).
Example: The current_R_value : 003
(3) Set R Value.
Send SMS:setr+space+ R_MIN+space+R_MAX to the GPS Tracker,
Example:setr 003 160

VT1000 USER MANUAL
10
The GPS Tracker will reply:Set R value ok.
Reference Picture
A
B
C
D