IWILL DK8S2 User manual

I
IW WI IL LL L®
®
D DK K8 8S S2 2™
™
H
Hi ig gh h P Pe er rf fo or rm ma an nc ce e S Se er rv ve er r B Bo oa ar rd d
U
Us se er r’ ’s s G Gu ui id de e

FCC Compliance Statement
This equipment has been tested and found to comply with limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in residential installations. This
equipment generates, uses, and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause interference to radio or
television equipment reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
1. Reorient or relocate the receiving antenna
2. Move the equipment away from the receiver
3. Plug the equipment into an outlet on a circuit different from that to which the
receiver is connected
4. Consult the dealer or an experienced radio/television technician for additional
suggestions
You are cautioned that any change or modifications to the equipment not expressly
approve by the party responsible for compliance could void Your authority to operate
such equipment.
This device complies with Part 15 of the FCC Rules. Operation is subjected to the
following two conditions
1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that
may cause undesired operation.
The information in this document is subject to change without notice.
IWILL Corp. makes no warranty of any kind with regard to this material, including, but
not limited to, the implied warranties of merchantability and fitness for a particular
purpose.
IWILL Corp. shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this
material.
IWILL Corp. assumes no responsibility for the use or reliability of its software on
equipment that is not furnished by IWILL Corp.
This document contains proprietary information that is protected by copyright. All rights
are reserved. No part of this publication may be reproduced, transcribed, stored in a
retrieval system, translated into any language or computer language, or transmitted in
any form whatsoever without the prior written consent of IWILL Corp.
Copyright©2003 by IWILL Corp. All rights reserved.
Other products and companies referred to herein the trademarks or registered
trademarks of their respective companies or mark holders.
Printed in Taiwan
Revision Version: 1.10
Release Date: May 2003

Contents
Chapter 1 1-1
OVERVIEW……………………………………………………..1-1
1.1. Unpacking……………………………………………...1-2
1.2. Features Highlight……………………………………..1-2
1.3. About This User Guide………………………………..1-4
1.4. Getting Help……………………………………………1-5
1.5. DK8S2 Motherboard Layout…………………………1-6
1.6. Motherboard Layout………………………………….1-7
Chapter 2 2-8
HARDWARE INSTALLATION…………………………………...2-8
2.1. Jumper Settings………………………………………..2-9
2.1.1. Clear CMOS Header…………………………………2-10
2.1.2. Enable Onboard VGA Header………………………..2-11
2.1.3. PCI-X Slot Speed Select Header……………………..2-11
2.1.4. PCI-64 Slot Speed Select Header…………………….2-12
2.2. Install Memory……………………………………….2-13
2.2.1. Memory Installation Procedures……………………..2-14
2.3. Install CPU……………………………………………2-16
2.3.1. CPU Installation Procedures…………………………2-16
2.4. Attach Cable to Connectors………………………….2-18
2.4.1. ATX Power Supply…………………………………..2-19
2.4.2. Floppy Disk Drive Connector………………………..2-20
2.4.3. Primary IDE connectors……………………………...2-20
2.4.4. Front Panel Switches…………………………………2-21
2.4.5. Front/Back/CPU/Aux Fan Connectors……………….2-23
2.4.6. Rear Panel I/O Ports………………………………….2-24
2.5. Install Expansion Cards……………………………...2-25
2.5.1. Expansion Card Installation Procedure .......................2-25
2.5.2. Assigning IRQs for PCI Expansion Cards...................2-26
2.6. Powering on Your Computer ..................................... 2-27
Chapter 3 3-28
BIOS SETUP………………………………………………….3-28
3.1. Starting BIOS Setup.................................................... 3-29
3.2. Using Setup……………………………………………3-30
3.3. Main Menu……………………………………………3-32

3.4. Advanced Menu........................................................... 3-33
3.4.1. IDE Configuration.......................................................3-34
3.4.2. Super I/O Configuration..............................................3-35
3.4.3. Onboard Device Configuration…………………..…...3-36
3.4.4. The Rest Advanced Setting.........................................3-37
3.5. PCI PnP Menu............................................................. 3-38
3.6. Boot Menu.................................................................... 3-40
3.6.1. Boot Settings Configuration........................................3-41
3.7. Security Menu.............................................................. 3-43
3.8. Chipset Menu............................................................... 3-44
3.8.1. NorthBridge Configuration .........................................3-45
3.8.2. ECC Configuration......................................................3-46
3.8.3. SouthBridge Configuration .........................................3-47
3.8.4. PCI-X Configuration...................................................3-48
3.9. Power Menu................................................................. 3-50
3.10.Exit Menu.................................................................... 3-51

1-1
C
Ch ha ap pt te er r 1 1
O
Ov ve er rv vi ie ew w
Thank you for choosing the DK8S2 high performance Server
motherboard. The DK8S2 is a dual AMD® Opteron micro-Socket
940 motherboard (M/B) based on the SSI form factor and is
configured with the AMD® HyperTransport I/O Hub 8111 and PCI-
X Tunnel 8131 chipsets. The board features a Hyper Transport
speed of 1600 MT (Mega Transfer per second).
For memory support, the DK8S2 provides eight sockets (four + four
configuration) accommodating up to 16 GB of memory using
registered PC3200/2700/2100 ECC DDR memory modules.
Flexibility and expandability are provided by two 64-bit/133MHz
PCI-X slots, two PCI 64-bit/66MHz PCI slots, and two 32-bit/33Mhz
PCI slots. This array of PCI slots enables numerous add-on cards
and provides Peer PCI transaction support to increase system
performance.
Other optional features such as onboard Silicon Image Serial ATA
RAID interfaces (available in DK8S2-SATA), dual INTEL® Gigabit
Ethernet controllers, and onboard ATI® RageXL video controller
with 8MB memory provide high system capabilities that meet a
wide range of demanding server applications.

1-2
1
1. .1 1. . U Un np pa ac ck ki in ng g
Remove all items from the box and make sure you have these
following items:
1. One DK8S2 motherboard
2. Two ATA 100 IDE ribbon cable (one piece in DK8S2-SATA)
3. One floppy ribbon cable
4. One bag of spare jumpers
5. One CD containing drivers and utilities
6. One DK8S2 User Guide
7. Four Serial ATA ribbon cable (available in DK8S2-SATA)
8. Two Serial ATA power cable (available in DK8S2-SATA)
If you discover damaged or missing items, please contact your
retailer.
1
1. .2 2. . F Fe ea at tu ur re es s H Hi ig gh hl li ig gh ht t
CPU 1. Supports dual AMD® Opteron
Socket 940 CPUs at 1600 MT per
second.
2. Built-in Memory Controller Hub
(MCH)
Chipset 1. Uses the latest AMD® 8111 Hyper
Transport I/O hub and 8131 PCI-X
Tunnel
2. DK8S2 supports the newest
technologies: 32bit/33MHz PCI
slots, 64bit/66MHz and 64
bit/133MHz PCI-X slots, USB
interface, Peer PCI Transaction
and I2C Bus support and more.
System
Memory
Support
1. DK8S2 provides 4+4 DIMM
sockets and supports total system
memory size up to 16GB.
2. Select from PC3200/2700/2100
ECC DDR registered DIMM
Expansion Slots 1. Provides two PCI-32-bit/33MHz,
two PCI 64-bit/66MHz, and two
PCI-X-64bit/133Mhz expansion
slots

1-3
2. 64-bit/66MHz PCI technology
enables bandwidth up to 528MB/s.
Onboard VGA
Chip
ATI® RageXL video controller with 8MB
memory
Onboard Dual
LAN
Dual Onboard Intel® 82541EI Gigabit
Ethernet controllers.
Super
Multi-I/O
1. Winbond super I/O W83627HF-
AW
2. One UART 16550 serial port
3. One external serial port
4. Dual onboard USB 1.1 connectors
5. Four extendable USB 1.1
connectors by headers
6. PS/2 mouse and keyboard
connectors with Wake-up function
Floppy Drive Supports 3.5” (1.44MB or 2.88MB) floppy
drive and Japanese standard “Floppy 3
mode” (3.5” disk drive: 1.44MB, 1.2MB,
720KB) and LS-120 floppy disk drives
(3.5” disk drive: 120 MB). BIOS supports
IDE CD-ROM boot-up.
Serial ATA RAID
(available in
DK8S2-SATA)
1. Four Integrated Silicon Image
Sil3114 Serial ATA ports
2. Support RAID 0, 1, 0+1
System
Management
1. AMC connector for IWILL Server
Remote Management Controller
card (ISRM) (optional)
2. IPMI 1.5 (optional with ISRM)
3. Prevent from abnormal system
down/data loss
4. Alert on LAN ready
5. Remote system controller ready
PC99
Compliant
The DK8S2 is fully compliant with the
Microsoft PC99 specification at both the
hardware and BIOS levels.
Dimension Extended SSI form factor-12”x13”

1-4
1
1. .3 3. . A Ab bo ou ut t T Th hi is s U Us se er r G Gu ui id de e
This manual explains how to build your system with DK8S2 in
detail. Please follow the procedures of this User Manual carefully
and pay special attention to these icons.
IMPORTANT
This icon informs you for particularly
important details regarding the setup or
maintenance of your system. While we
point out the most vital paragraphs in a
chapter, you should always read every
word carefully. Failing to do so can cause
exasperation.
WARNING
This icon alerted you for potential dangers
during setting up your system with DK8S2.
These warnings should not be regarded as
the whole of your safety regimen. Never
forget that computer are electronic devices
and are capable of delivering a shock.
Prevent damage to yourself and to your
board: always ensure that your system is
turned off and unplugged the power cords
whenever you are working with it, and that
you are equipped
NOTE
This icon alerted you for notice during
setting up your system. It provides you can
useful alert during setting up a new system.
TIP
This icon will show you how to configure
your system with DK8S2 in an easy and
simple ways. This icon always provides
some useful description to help you
configure your system.

1-5
1
1. .4 4. . G Ge et tt ti in ng g H He el lp p
If a problem arises with yours system during Installation or OS
operating, you should ask your dealer for help first as your system
has most likely be configured by them. They always have the best
idea and quick response for your symptoms. If your dealer is near
to your locations, you should bring your system to them to have it
quickly serviced instead of attempting to solve the problem by
yourself.
1. Go to IWILL website at www.iwill.net and navigate to this
product page which contain links to product updates such as
Jumper settings or BIOS updates.
2. FAQ sections on IWILL Website are often helpful since other
user's questions are often your own.
3. Email us at: [email protected] and we will try to answer your
questions within 24 hours.

1-6
1
1. .5 5. . D DK K8 8S S2 2 M Mo ot th he er rb bo oa ar rd d L La ay yo ou ut t
Figure 1-1: Motherboard features
Keyboard
Mouse
USBCOM 1VGALAN1
LAN2ATI Rage XL
CPU 1
Memory
DIMM
2,3,0,1
Power
CPU 0
Memory
DIMM
1,0,3,2
Silicon Image S-ATA Chip
(Available in DK8S2-SATA)
S-ATA Port
4,2,1,3
PCI-X 133/100
AMD 8111
AMD 8131
Slim Floppy
Floppy
IDE1,IDE0
PCI 64
PCI 32
COM 2
IPMI Connector