Jaypro Sports BBFP-40SM User manual

Page 1of 9
-- BBFP-40SM --
-- SBFP-40SM --
(40’ PROFESSIONAL / SOFTBALL FOUL POLE)
Installation Instructions
Call Jaypro Sports Equipment at 1-800-243-0533
during regular business hours for technical support.
www.jaypro.com

Page 2of 9
40’ Professional / Soft Ball Foul Pole, BBFP-40SM / SBFP-40SM
QUANTITY IS FOR ONE COMPLETE FOUL POLE
ITEM
QTY
IMAGE
DESCRIPTION
1
1
TOP UPRIGHT POLE
P/N: BBFP-40TU
2
1
BOTTOM UPRIGHT POLE
P/N: BBFP-40SM-BU
3
6
MIDDLE PANEL
P/N: BBPS-B
4
20
3/8” FLAT WASHER
P/N: HW2047
5
10
3/8”-16 NYLON LOCK NUT
P/N: HN265
6
10
3/8”-16 x 1” LONG HEX HEAD
P/N: HS286
7
54
7/16” FLAT WASHER
P/N: HW5042
8
18
7/16”-14 NYLON LOCK NUT
P/N: HN5070
9
18
7/16”-14 x 8” LONG HEX HEAD
P/N: HS5386
10
2
1/2"-13 x 8” LONG HEX HEAD
P/N: HS5066
11
4
1/2" FLAT WASHER
P/N: HW2044
12
2
1/2”-13 NYLON LOCK NUT
P/N: HN2951
ITEM
QTY
IMAGE
DESCRIPTION
•Unpack all parts and check against parts list to ensure that all have been included.
•Inspect all parts for damage. Report any damages to the trucking company.

Page 3of 9
ITEM
QTY
IMAGE
DESCRIPTION
13
4
24” LONG L-HOOK
P/N: SR5401
14
1
LEVELING PLATE
P/N: SR5402
15
12
1”-8” HEX NUT
P/N: HN274
16
8
1” FLAT WASHER
P/N: HW5052
17
1
TOP CAP FOR 6-5/8" OD
P/N: EC0070
ITEM
QTY
IMAGE
DESCRIPTION
•Unpack all parts and check against parts list to ensure that all have been included.
•Inspect all parts for damage. Report any damages to the trucking company.

Page 4of 9
IMPORTANT NOTICE:
1) BEFORE EACH USE CHECK EQUIPMENT FOR PROPER CONNECTING
HARDWARE AND STRUCTURAL INTEGRITY. REPLACE DAMAGED OR
MISSING HARDWARE IMMEDIATELY.
2) USE OF THIS EQUIPMENT OTHER THAN INTENDED, MAY BE
HAZARDOUS.
3) ALTERATION OR MODIFICATION OF THIS EQUIPMENT MAY BE
HAZARDOUS AND RESULT IN INJURY. FOR REPAIR OR
REPLACEMENT, CONTACT YOUR DEALER OR JAYPRO SPORTS.
4) CONCRETE SHOULD BE A MINIMUM 4000-PSI MIX.
ASSEMBLY INSTRUCTIONS
TOOLS / MATERIALS REQUIRED:
(6) 3/4” x 66” Long Re-Bar (NOT INCLUDED - Consult with local building code)
(1) 1-1/2” , 9/16” , 5/8” Socket Wrench and Box Wrench
(1) Rubber Mallet
(1) Lifting Device (i.e. Crane)
(1) Concrete (4000 psi mix)
(1) Leveling Device
•Unpack all parts and check against parts list to ensure that all have been
included.
•Inspect all parts for damage. Report any damages to the trucking
company.
Site Prep:
1) Determine the proper location of foul poles as shown in figure 1 & 2 on the playing
field that is clear of debris or obstruction. Dig the footing holes to the dimensions as
shown on the illustration on the next page. These are suggested dimensions for
average soil conditions, consult local building codes. Dimensions may need to be
adjusted in areas subject to high wind loads.
2) Assemble L-Hook to leveling plate by installing 1”-8 hex nuts onto the threaded ends
6” apart. Install 1”-8 hex nut onto threaded ends and tighten down so that the leveling
plate is now held securely between the two nuts until the concrete done curing.
3) Pour the footing as shown in figure 2, using minimum 4,000 psi mix.
4) Place the assembled L-Hook & leveling plate in the concrete, level and square.
5) Let the foundation cure for a minimum of 96 hrs.
Important: The anchor bolts must be oriented to
position the foul pole in accordance with figure 1.

Page 5of 9
1”-8 HEX NUTS w/ WASHERS
Once foundation finished curing,
backoff the nuts and place a washer.
FIGURE: 2
Note: These are suggested dimensions for average soil conditions, consult local building codes.
*For Areas Subject To Higher Wind Loads Footing Dimensions May Need To Be Adjusted.
See wind loading spec sheet.
REBAR BASKET
(6) ¾” x 66” REBAR (BY OTHERS)
FIGURE: 1

Page 6of 9
Bottom Pole Section:
1. Lower the bottom pole over the L-Hook into the jellybean slots.
2. Adjust the bottom nuts up or down to plumb the bottom pole.
3. Rotate the upright as needed to align the panel mounting holes per the figure 1 (note
mounting holes for panels).
4. Secure the mounting plate with 1”-8 nuts & washers.
FIGURE: 3
BOTTOM POLE
P/N: BBFP-40SM-BU
1”-8 HEX NUTS
w/ WASHERS
MOUNTING HOLES
FOR PANELS

Page 7of 9
Top Pole Section:
1. Install the top cap by tapping it on with a rubber mallet.
2. Insert the top pole into the bottom pole as shown below.
3. Line up the holes for the wing panels in both the top and bottom poles.
FIGURE: 4
TOP UPRIGHT POLE
P/N: BBFP-40TU
BOTTOM UPRIGHT POLE
P/N: BBFP-40SM-BU
(apply light layer of grease if
needed)
TOP CAP
P/N: EC0070
TOP UPRIGHT POLE
P/N: BBFP-40TU

Page 8of 9
Wing Panels:
1. Attach all the wing panels per figure 5. Orient the panels so the front side is facing the
field. (Note image shown is from the back side of panels.)
FIGURE: 5
(Backside of Panels Shown)
7/16”-14 x 8” HEX BOLT
P/N: HS5386
7/16” FLAT WASHER
P/N: HW5042
7/16”-14 LOCK NUT
P/N: HN5070
3/8”-16 x 1” HEX BOLT
P/N: HS286
3/8” FLAT WASHER
P/N: HW5042
PANEL P/N: BBPS-B
PANEL P/N: BBPS-B
PANEL P/N: BBPS-B
PANEL P/N: BBPS-B
PANEL P/N: BBPS-B
PANEL P/N: BBPS-B

Page 9of 9
2. Rotate the pole to position the panels perpendicular to the foul line, as shown in figure 1.
If needed, rotate the top pole so the wing panels attaching to the bottom pole are in line
with the top. Install the bottom two panels as shown in figure 5.
3. Drill the two holes in the top upright pole to accommodate the hardware as shown
figure 6. This finalize the location. Note drill holes for 1/2” hardware.
4. Spray paint expose hardware if desired.
FIGURE: 6
1/2” FLAT WASHER
P/N: HW2044
1/2”-13 LOCK NUT
P/N: HN2951
1/2”-13 x 8” LONG HEX BOLT
P/N: HS5066
1/2” FLAT WASHER
P/N: HW2044
FIGURE: 1