Jegs 555-81449 User manual

Mobile Tool Chest Assembly Guide
555-81449
Black Powder Coated | 15-Drawer | 72 in.

Parts List
1
# # #
1
2
3
4
5
6
1
1
4
1
1
6
Cabinet Top
Handle
Bolt (1/4in. x 1/2in.)
Power Strip
Power Cord
Drawer (Medium 1/2)
DESCRIPTION DESCRIPTION DESCRIPTION
QTY QTY QTY
7
8
9
10
11
12
Drawer (Large 1/2)
Drawer (X-Large 1/2)
Drawer Sliders
Caster (Locking Swivel)
Bolts (3/8in x 1 in.)
Lock & Key
13
14
15
16
17
18
Drawer (Medium)
Drawer (Large)
Drawer (X-Large)
Drawer Liner (Narrow)
Drawer Liner (Wide)
Caster (Fixed)
2
2
36
2
16
1
3
1
1
10
5
2

2
Introduction
We would like to take this opportunity to thank you
for purchasing this JEGS Mobile Black Powder
Coated 15-drawer Tool Chest. We welcome any
comments or feedback you might have. If you
have any questions about this product or about
the installation procedure, please feel free to
contact us at 1.800.345.4545.
Black powder coated steel construction with
a 1 in. thick black MDF worktop. 100 lb.
capacity drawers with non- slip liners. Four
casters, two fixed and two swivel (which
include brakes). Comes with two heavy-duty
side handles for comfort and control
when maneuvering. Supplied with lock and
keys.
IMPORTANT
Please read these instructions carefully.
Note the safe operation requirements,
warnings, and cautions. Use this product for
the purpose for which it is intended. Failure to
do so may result in damage and/or personal
injury, and will void the warranty. Keep these
instructions in a safe place for future use.
Safety
•Locate in a suitable work area.
•Monitor children near the cabinet.
•Do not open more than one drawer at a time.
•Fill from the bottom drawer.
• If the tool cabinet is lled from the top drawer
down, it will be top heavy and may fall over.
•Do not attempt to lift by the side handles, use
chains, ropes or other lifting devices.
• Do not use the cabinet as a step or climb
on the drawers.
•Do not alter the product in any way.
• Do not weld on external lock bars or attach
electrical equipment.
• Doing so may damage the product and
cause personal injury.
•Keep on a level surface
• When moving the cabinet DO NOT pull it. Push
the cabinet to prevent injury.
• Close and lock the drawers before moving the
cabinet. If the drawers come open they could
make the cabinet unstable.
• Apply brake when the cabinet is in the desired
position.
• Do not mount on a truck bed or any other
moving object.
•Be aware of sharp edges.
Overall Size
Medium 1/2Drawer
Large 1/2Drawer
X-Large 1/2Drawer
Medium Drawer
Large Drawer
X-Large Drawer
78.000 x 18.500 x 35.500
14.750 x 15 x 2.560
14.750 x 15 x 5.510
14.750 x 15 x 8.660
33.750 x 15 x 2.560
33.750 x 15 x 5.510
33.750 x 15 x 8.660
6
2
2
3
1
1
COMPONENT DIMENSIONS (WxDxH) IN.
SPECIFICATIONS
QTY

Installation
HANDLE (Fig.01)
1. Attach with 1/4in. x 1/2in. bolts, lock washer
and at washers.
CASTERS (Fig.02)
1. WARNING. Two or more people are required
to lay down or stand up the cabinet. Lock
drawers before turning over.
2. Carefully lay the cabinet upside down on a soft
mat for protection
3. Fit the swivel/locking casters on the handle
side of the cabinet using 3/8in. x 1 in. bolts.
Insert the bolts through each caster and into
the bottom of the cabinet. Tighten securely.
4. Repeat for the two rigid casters on the other
side of the cabinet.
Figure 01
Figure 02
DRAWERS (Fig.03)
1. New drawer slides may be stiff and difcult
to open at rst. A gentle outward pull should
release the safety that prevents the drawer
from opening whilst the cabinet is being moved.
2. Remove drawers from their slides as below.
• Pull left slide tab down and pull right side
slide tab up.
Figure 03
3

Maintenance
Electronics
1. To clean use a soft cloth that will not scratch
the surface.
2. DO NOT use solvents of any kind they may
damage the surface.
3. Liquid spills should be removed immediately,
use a soft clean cloth to blot the spill gently -
avoid rubbing.
4. Grease the casters with good quality grease
once a year.
5. Lubricate the drawer slides twice a year with
light duty oil.
POWER STRIP (Fig.04)
This cabinet features a pre-installed power strip with
(4) 5-15 outlets and (2) USB ports, conveniently
located for easy access. The included power
strip has the following ratings:
Maximum Amperage Load.................12A
Maximum Voltage..............................125V
Cycle....................................................60 Hz
Maximum Wattage.........................1500W
USB Output......................5VDC, Max. 2.1A
Plug the provided power cord into the power strip
socket.
Figure 04
110V CIRCUIT REQUIREMENTS
This tool chest is pre-wired to connect to a power
supply circuit that has a veried ground and meets
the following requirements.
Nominal Voltage...........110V, 115V, 120V
Cycle......................................................60Hz
Phase.......................................Single-Phase
Power Supply Circuit....................15 Amps
A power supply circuit includes all electrical
equipment between the breaker box or fuse panel in
the building and the power strip. The power supply
circuit used for this power strip must be sized to
safely handle the full-load current drawn from
the power strip for an extended period of time.
(If this power strip is connected to a circuit
protected by fuses, use a “D” time delay fuse.
GROUNDING & PLUG REQUIREMENTS
This power strip MUST be grounded. In the event
of certain malfunctions or breakdowns, grounding
reduces the risk of electric shock by providing a
path of least resistance for electric current.
4
Socket
Power Strip
Power Cord
with Plug

Electronics
This power strip is equipped with a power cord
that has an equipment-grounding wire and a
grounding plug. Only insert plug into a matching
receptacle (outlet) that is properly installed and
grounded in accordance with all local codes and
ordinances. DO NOT modify the provided plug!
Grounded 5-15 Receptacle
Neutral Hot
WARNING
• Do not connect to plug receptacle via
extension cords or in series with other
power strips.
•
Keep electrical connections clear of am mable
materials.
• Keep electrical connections dry. Do not use
in damp or wet conditions.
•Do not connect devices to power strip that
draw more than listed power strip rating.
Equipment must be used in accordance with
the instructions.
• Power strips are designed for use with
low-powered loads, such as battery
chargers. Not designed for use with
high-powered loads, such as space heaters
or microwaves.
• Do not run cord under oor coverings or
where it may be tripped over.
•Not meant for outdoor use.
• Prevent unauthorized use by children or
untrained users.
WARNING
Electrocution, re, shock,
or equipment damage may
occur if power strip is not
properly grounded and
connected to power supply.
5


 


 

    
      





IMPORNT


  

LL

6