Jenn-Air 27" (68.6 CM) User manual

INSTALLATION INSTRUCTIONS
27" (68.6 CM) AND 30" (76.2 CM) ELECTRIC BUILT-IN
MICROWAVE/OVEN COMBINATION
INSTRUCTIONS D’INSTALLATION
FOUR À MICRO-ONDES ET FOUR CONVENTIONNEL
ÉLECTRIQUES COMBINÉS ET ENCASTRÉS DE
27" (68,6 CM) ET 30" (76,2 CM)
Table of Contents / Table des matières
BUILT-IN MICROWAVE/OVEN COMBINATION SAFETY .................2
INSTALLATION REQUIREMENTS ......................................................2
Tools and Parts ..................................................................................2
Location Requirements......................................................................2
Electrical Requirements .....................................................................4
INSTALLATION INSTRUCTIONS ........................................................5
Prepare Built-In Microwave/Oven Combination................................5
Remove Oven Door............................................................................5
Make Electrical Connection ...............................................................5
Install Oven.........................................................................................7
Complete Installation ........................................................................ 8
SÉCURITÉ DU FOUR À MICRO-ONDES ET DU FOUR
CONVENTIONNEL COMBINÉS ET ENCASTRÉS.............................. 9
EXIGENCES D'INSTALLATION ........................................................... 9
Outillage et pièces ............................................................................. 9
Exigences d'emplacement ................................................................ 9
Spécifications électriques................................................................ 11
INSTRUCTIONS D'INSTALLATION .................................................. 12
Préparation de l'ensemble des fours encastrés
(micro-ondes/conventionnel)........................................................... 12
Dépose de la porte du four.............................................................. 12
Raccordement électrique ................................................................ 12
Installation du four ........................................................................... 14
Achever l'installation........................................................................ 16
IMPORTANT:
Save for local electrical inspector's use.
IMPORTANT :
À conserver pour consultation par l'inspecteur local des installations électriques.
W10221384C

2
BUILT-IN MICROWAVE/OVEN COMBINATION SAFETY
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
■Adjustable wrench or ⁵⁄₈" wrench
■Phillips screwdriver
■Flat-blade screwdriver
■Measuring tape
■Drill (for wall cabinet installations)
■1¹⁄₄" (3.4 cm) drill bit (for wall cabinet installations)
■Level
Parts needed
■UL listed or CSA approved conduit connector
■UL listed wire connectors
Parts supplied
■Six # 8–14 x ³⁄₄" screws
■Bottom vent
■Two # 8–18 x ³⁄₈" screws - bottom vent
Check local codes. Check existing electrical supply. See
“Electrical Requirements.”
It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
Location Requirements
Make sure you have everything needed for correct installation.
IMPORTANT: Observe all governing codes and ordinances.
■Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance with oven.
■Recessed installation area must provide complete enclosure
around the recessed portion of the oven.
■Grounded electrical supply is required. See “Electrical
Requirements” section.
■Electrical supply junction box should be located 3" (7.6 cm)
maximum below the support surface when the oven is
installed in a wall cabinet. A 1¹⁄₄" (3.4 cm) minimum diameter
hole should have been drilled only in the left rear corner of the
support surface to pass the appliance cable through to the
junction box.
■Oven support surface must be solid, level and flush with
bottom of cabinet cutout. Floor must be able to support a total
weight of (microwave and built-in oven) of 249 lbs (113 kg) for
30" (76.2 cm) oven and 236 lbs (107 kg) for 27" (68.6 cm)
oven.
IMPORTANT: To avoid damage to your cabinets, check with your
builder or cabinet supplier to make sure that the materials used
will not discolor, delaminate or sustain other damage. This oven
has been designed in accordance with the requirements of UL
and CSA International and complies with the maximum allowable
wood cabinet temperatures of 194° (90°C).
You can be killed or seriously injured if you don't immediately
You can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING

3
Product Dimensions Cabinet Dimensions
27" (68.6 cm) models
A. 25¹⁄₄" (64.1 cm) max. recessed
width
B. 43¹⁄₁₆" (109.4 cm) max. overall
height
C. 26³⁄₄" (67.9 cm) max. overall
width
D. 23⁵⁄₈" (60.0 cm) max. recessed
depth
E. 41" (104.2 cm) max. recessed
height
30" (76.2 cm) models
A. 28" (71.1 cm) max. recessed
width
B. 43¹⁄₁₆" (109.4 cm) max. overall
height
C. 29³⁄₄" (75.6 cm) max. overall
width
D. 23⁵⁄₈" (60.0 cm) max. recessed
depth
E. 41" (104.2 cm) max. recessed
height
E
C
D
B
A
27" (68.6 cm) models
A. 27" (68.6 cm) min. cabinet width
B. 43⁵⁄₁₆" (110.0 cm) from bottom
of cutout to bottom of upper
cabinet door
C.19¹⁄₄" (48.9 cm) recommended
bottom of cutout to floor. 4"
(10.2 cm) to 19¹⁄₄" (48.9 cm)
bottom of cutout to floor is
acceptable.
D. 25¹⁄₂" (64.8 cm) cutout width
E. 1¹⁄₂" (3.8 cm) min. bottom of
cutout to top of cabinet door
F. 41¹⁄₄" (104.8 cm) cutout height
G. 24" (61.0 cm) minimum cutout
depth
30" (76.2 cm) models
A. 30" (76.2 cm) min. cabinet
width
B. 43⁵⁄₁₆" (110.0 cm) from bottom
of cutout to bottom of upper
cabinet door
C. 19¹⁄₄" (48.9 cm) recommended
bottom of cutout to floor. 4"
(10.2 cm) to 19¹⁄₄" (48.9 cm)
bottom of cutout to floor is
acceptable.
D. 28¹⁄₂" (72.4 cm) cutout width
E. 1¹⁄₂" (3.8 cm) min. bottom of
cutout to top of cabinet door
F. 41 ¹⁄₄" (104.8 cm) cutout height
G. 24" (61.0 cm) minimum cutout
depth
A
B
C
D
E
F
G

4
Electrical Requirements
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine that
the ground path and the wire gauge are in accordance with local
codes.
Check with a qualified electrical installer if you are not sure the
oven is properly grounded.
This oven must be connected to a grounded metal, permanent
wiring system.
Be sure that the electrical connection and wire size are adequate
and in conformance with the National Electrical Code, ANSI/NFPA
70-latest edition or CSA Standards C22.1-94, Canadian Electrical
Code, Part 1 and C22.2 No. O-M91-latest edition, and all local
codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
Electrical Connection
To properly install your oven, you must determine the type of
electrical connection you will be using and follow the instructions
provided for it here.
■Oven must be connected to the proper electrical voltage and
frequency as specified on the model/serial number rating
plate. The model/serial number rating plate is located near
center vent of the lower oven. See the following illustration.
■Models rated from 7.3 to 9 kW at 240 volts (5.4 to 7.4 kW at
208 volts) require a separate 40-amp circuit. Models rated at
4.8 kW and below at 240 volts (3.6 kW and below at 208 volts)
require a separate 20-amp circuit.
■A circuit breaker is recommended.
■Connect directly to the fused disconnect (or circuit breaker
box) through flexible, armored or nonmetallic sheathed,
copper cable (with grounding wire). See “Make Electrical
Connection” section.
■Flexible conduit from the oven should be connected directly to
the junction box.
■Do not cut the conduit. The length of conduit provided is for
serviceability of the oven.
■A UL listed or CSA approved conduit connector must be
provided.
■If the house has aluminum wiring follow the procedure below:
1. Connect a section of solid copper wire to the pigtail
leads.
2. Connect the aluminum wiring to the added section of
copper wire using special connectors and/or tools
designed and UL listed for joining copper to aluminum.
Follow the electrical connector manufacturer's recommended
procedure. Aluminum/copper connection must conform with
local codes and industry accepted wiring practices.
A. Model/serial number plate (located on
underside of center vent)
A

5
INSTALLATION INSTRUCTIONS
Prepare Built-In Microwave/Oven
Combination
1. Decide on the final location for the oven. Avoid drilling into or
severing wiring during installation.
2. To avoid floor damage, set the oven onto cardboard prior to
installation. Do not use handle or any portion of the front
frame for lifting.
3. Remove the shipping materials and tape from the oven.
4. Remove the hardware package from inside the bag containing
literature.
5. Remove and set aside racks and other parts from inside the
oven.
6. Move oven and cardboard close to the oven’s final location.
Remove Oven Door
IMPORTANT: Use both hands to remove oven door(s).
1. Open the oven door to the full open position.
2. Locate the oven door latches in both corners of the oven door,
and rotate the latches forward to the unlocked position.
3. Grasp the edges of the oven door with both hands and close
the oven door until it will no longer close. Lift and pull oven
door toward you and remove. Set the oven door(s) aside on a
covered work surface.
Make Electrical Connection
This oven is manufactured with a neutral (white) power supply
wire and a cabinet-connected green (or bare) ground wire twisted
together.
1. Disconnect power.
2. Feed the flexible conduit from the oven through the opening in
the cabinet.
3. Remove junction box cover, if it is present.
A. Oven door latch in locked
position B. Oven door latch in unlocked
position
WARNING
Excessive Weight Hazard
Use two or more people to move and install oven.
Failure to do so can result in back or other injury.
A
B
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Use 8 gauge solid copper wire.
Electrically ground oven.
Failure to follow these instructions can result in death,
fire, or electrical shock.

6
4. Install a UL listed or CSA approved conduit connector to the
junction box.
5. Route the flexible conduit from the oven to the junction box
through a UL listed or CSA approved conduit connector.
6. Tighten screws on conduit connector.
7. See “Electrical Connection Options Chart” to complete
installation for your type of electrical connection.
Electrical Connection Options Chart
4-Wire Cable from Home Power Supply
IMPORTANT: Use the 4-wire cable from home power supply in
the U.S. where local codes do not allow grounding through
neutral, New Branch circuit installations (1996 NEC), mobile
homes and recreational vehicles, new construction and in
Canada.
1. Connect the 2 black wires (B) together using a UL listed wire
connector.
2. Connect the 2 red wires (C) together using a UL listed wire
connector.
3. Untwist white wire from green (or bare) ground wire coming
from the oven.
4. Connect the 2 white wires (F) together using a UL listed wire
connector.
5. Connect the green (or bare) ground wire (H) from the oven
cable to the green (or bare) ground wire (in the junction box)
using a UL listed wire connector.
6. Install junction box cover.
3-Wire Cable from Home Power Supply - U.S. Only
IMPORTANT: Use the 3-wire cable from home power supply
where local codes permit a 3-wire connection.
1. Connect the 2 black wires (C) together using a UL listed wire
connector.
2. Connect the 2 white wires (D) and the green (or bare) ground
wire (of the oven cable) using a UL listed wire connector.
3. Connect the 2 red wires (G) together using a UL listed wire
connector.
4. Install junction box cover.
A. UL listed or CSA approved conduit connector
If your home has: Go to section:
4-wire 4-wire Cable from Home
Power Supply
3-wire 3-wire Cable from Home
Power Supply
A. Cable from home power supply
B. Black wires
C. Red wires
D. 4-wire flexible conduit from
oven
E. Junction box
F. W h i t e w i r e s
G. UL listed wire connectors
H. Green (or bare) ground wires
I. UL listed or CSA approved
conduit connector
A
½"
(1.3 cm)
½"
(1.3 cm)
A
B
C
D
E
F
G
H
I
A. Cable from home power supply
B. Junction box
C. Black wires
D. White wires
E. Green (or bare) ground wire
(from oven)
F. 4-wire flexible conduit from
oven
G. Red wires
H. UL listed wire connectors
I. UL listed or CSA approved
conduit connector
B
C
D
E
F
H
G
A
I

7
Install Oven
1. Using 2 or more people, lift oven partially into cabinet cutout.
Use the oven opening as an area to grip.
NOTE: Push against seal area of oven front frame when
pushing oven into cabinet. Do not push against outside
edges.
2. Push oven completely into cabinet and center oven into
cabinet cutout.
3. Securely fasten oven to cabinet using the # 8–14 x ³⁄₄" screws
provided. Insert the screws through holes in decorative trim.
Do not overtighten screws.
4. The bottom vent is taped to the top of the oven chassis
enclosure. See the following instructions to install.
■Align mounting hole in bottom vent to holes in the oven
frame.
■With one #8–18 x ³⁄₈" screw for each side of the vent,
fasten vent securely to the oven frame.
IMPORTANT: Do not block air intake along bottom of oven.
5. Replace oven racks.
6. Grasp door at each side.
7. Replace oven door by aligning and inserting ends of hinges
into hinge slots in the oven frame.
8. Push hinges in as far as they will go and open the oven door
to the fully open position. You should feel the oven door drop
into place.
9. Move the latches back to the locked position.
10. Check that door is free to open and close. If it is not, repeat
the removal and installation procedures. See “Remove Oven
Door” section.
11. Reconnect power.
12. Display panel will light briefly, and the clock should appear in
the display.
13. If display panel does not light, please reference the
“Assistance or Service” section of the Use and Care Guide or
contact the dealer from whom you purchased your oven.
A. Decorative trim
B. Insert screw.
A
B

8
Complete Installation
1. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
2. Check that you have all of your tools.
3. Dispose of/recycle all packaging materials.
4. For oven use and cleaning, read the Use and Care Guide.
Check Operation of Lower Oven
1. Turn power on.
2. At first use, set up the language, regional settings, clock, date
and screen appearance. For more details, read the Use and
Care Guide.
3. Press OVEN.
4. Touch BROIL.
5. Set the temperature.
6. Touch START.
If oven(s) does not operate, check the following:
■Household fuse is intact and tight; or circuit breaker has
not tripped.
■Electrical supply is connected.
■See “Troubleshooting” section in the Use and Care Guide.
7. When oven has been on for 5 minutes, feel for heat.
If you do not feel heat or if an error message appears in the
display, turn off the oven and contact qualified technician.
8. Touch CANCEL OVEN.
Check Operation of Microwave Oven
1. Fill a microwave-safe container with 1 cup (250 mL) of water
and place container inside microwave oven. Close door firmly.
2. From the main menu press microwave or open microwave
oven door.
3. Touch COOK.
4. Set power level, temperature and cook time to “2:00” minutes.
5. Touch START.
If microwave oven does not operate, check the following:
■Household fuse is intact and tight; or circuit breaker has
not tripped.
■Electrical supply is connected.
■See “Troubleshooting” section in the Use and Care Guide.
When display reads “1:00” minute, open microwave oven
door. The microwave oven should stop cooking. Close door
firmly. The interior microwave oven light should turn off.
6. Touch START to resume a preset cycle. The microwave oven
should begin cooking, and the microwave oven interior light
should be on. Let microwave oven complete cooking time.
Tones will sound at the end of the cooking time, and the
microwave oven will shut off.
7. Open microwave oven door and slowly remove container.
Water in container should be hot. To set the clock and other
oven functions, refer to the Use and Care Guide.
If you need Assistance or Service:
Please reference the “Assistance or Service” section of the Use
and Care Guide or contact the dealer from whom you purchased
your built-in and microwave ovens.

9
SÉCURITÉ DU FOUR À MICRO-ONDES ET DU FOUR
CONVENTIONNEL COMBINÉS ET ENCASTRÉS
EXIGENCES D'INSTALLATION
Outillage et pièces
Rassembler les outils et pièces nécessaires avant de commencer
l’installation. Lire et suivre les instructions fournies avec les outils
indiqués ici.
Outillage nécessaire
■Clé à molette ou clé de 5/8"
■Tournevis Phillips
■Tournevis à lame plate
■Mètre ruban
■Perceuse (pour l'installation dans un placard mural)
■Foret de 1¹⁄₄" (3,4 cm) (pour l'installation dans un placard
mural)
■Niveau
Pièces nécessaires
■Connecteur de conduit (homologation UL ou CSA)
■Connecteurs de fils (homologation UL)
Pièces fournies
■Vis n° 8–14 x ³⁄₄"
■Évent du fond
■Deux vis n° 8–18 x ³⁄₈" - évent du fond
Consulter les codes locaux. Vérifier l'alimentation électrique
existante. Voir “Spécifications électriques”.
Il est recommandé de faire réaliser tous les raccordements
électriques par un électricien qualifié agréé.
Exigences d'emplacement
S’assurer d’avoir tout le nécessaire pour une installation
convenable.
IMPORTANT : Observer les dispositions de tous les codes et
règlements en vigueur.
■Respecter les dimensions indiquées pour les ouvertures à
découper dans les placards. Ces dimensions tiennent compte
des dégagements de séparation minimaux nécessaires pour
le four.
■L’espace d’installation doit permettre la formation d’une
enceinte complète autour de la partie encastrée du four.
■Une source d'électricité avec liaison à la terre est nécessaire.
Voir la section “Spécifications électriques”.
■Le boîtier de connexion doit être situé à 3" (7,6 cm) maximum
au-dessous de la surface de support lorsque le four est
installé dans un placard mural. Un trou de diamètre minimal
de 1¹⁄₄" (3,4 cm) doit avoir été percé uniquement dans l’angle
arrière gauche de la surface de support pour le passage du
câble d’alimentation de l’appareil jusqu'au boîtier de
connexion.
■La surface de support du four doit être robuste, horizontale et
en affleurement avec le bas de l’ouverture découpée dans le
placard. Le plancher doit être capable de supporter un poids
total (four à micro-ondes et four encastré) de 249 lb (113 kg)
pour le four de 30" (76,2 cm) et de 236 lb (107 kg) pour le four
de 27" (68,6 cm).
Risque possible de décès ou de blessure grave si vous ne
suivez pas immédiatement les instructions.
Risque possible de décès ou de blessure grave si vous
ne suivez pas les instructions.
Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
Votre sécurité et celle des autres est très importante.
Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de
toujours lire tous les messages de sécurité et de vous y conformer.
AVERTISSEMENT
DANGER
Voici le symbole d’alerte de sécurité.
Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous
et à d’autres.
Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou
“AVERTISSEMENT”. Ces mots signifient :

10
IMPORTANT : Pour éviter tout dommage aux placards, consulter
le constructeur ou le fabricant du placard pour déterminer si les
matériaux utilisés ne subiront pas un changement de couleur, une
déstratification ou d'autres dommages. Ce four a été conçu
conformément aux exigences UL et aux normes de la CSA
International; il respecte la température maximale autorisée pour
les placards en bois : 194°F (90°C).
Dimensions du produit
Dimensions du placard
Modèles de 27" (68,6 cm)
A. 25¹⁄₄" (64,1 cm) de largeur
d'encastrement max.
B. 43¹⁄₁₆" (109,4 cm) de hauteur
totale max.
C. 26³⁄₄" (67,9 cm) de largeur
totale max.
D. 23⁵⁄₈" (60,0 cm) de profondeur
totale max.
E. Hauteur de l'encastrement de
41" (104,2 cm) max.
Modèles de 30" (76,2 cm)
A. 28" (71,1 cm) de largeur
d'encastrement max.
B. 43¹⁄₁₆" (109,4 cm) de hauteur
totale max.
C. 29³⁄₄" (75,6 cm) de largeur
totale max.
D. 23⁵⁄₈" (60,0 cm) de profondeur
totale max.
E. Hauteur de l'encastrement de
41" (104,2 cm) max.
E
C
D
B
A
Modèles de 27" (68,6 cm)
A. 27" (68,6 cm) min. de largeur
de placard
B. 43⁵⁄₁₆" (110,0 cm) du fond de
l'encastrement au-dessous de
la porte du placard supérieur
C. Distance recommandée de
19¹⁄₄" (48,9 cm) entre le bas
de l'ouverture et le plancher.
Une distance de 4" (10,2 cm)
à 19¹⁄₄" (48,9 cm) entre le bas
de l'ouverture et le plancher
est acceptable.
D. 25¹⁄₂" (64,8 cm) Largeur de
l'encastrement
E. 1¹⁄₂" (3,8 cm) min. du fond de
l'encastrement au-dessus de
la porte du placard
F. 41¹⁄₄" (104,8 cm) Hauteur
d'encastrement
G. 24" (61.0 cm) profondeur
d'encastrement minimale
Modèles de 30" (76,2 cm)
A. 30" (76,2 cm) min. de largeur de
placard
B. 43⁵⁄₁₆" (110,0 cm) du fond de
l'encastrement au-dessous de
la porte du placard supérieur
C. Distance recommandée de
19¹⁄₄" (48,9 cm) entre le bas de
l'ouverture et le plancher. Une
distance de 4" (10,2 cm) à 19¹⁄₄"
(48,9 cm) entre le bas de
l'ouverture et le plancher est
acceptable.
D. 28¹⁄₂" [72,4 cm] Largeur de
l'encastrement
E. 1¹⁄₂" (3,8 cm) min. du fond de
l'encastrement au-dessus de la
porte du placard
F. 41¹⁄₄" (104,8 cm) Hauteur
d'encastrement
G. 24" (61.0 cm) profondeur
d'encastrement minimale
A
B
C
D
E
F
G