JessEm 05150 User manual

Steel Router Stand
User Manual
Model #05150
324 Desbrisay Avenue
Moncton, New Brunswick,
E1E 0G8, Canada
Toll Free: 800-436-6799
Local Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www. JessEm.com
Tools Required: 3/16” Hex Key (Provided)
Thank you for choosing this product from JessEm
Tool Company. We appreciate your support and
hope that our product serves you well. This product
is designed to provide many years of reliable service
provided it is used as intended and taken care of.
This user manual will assist you in assembly and
general operaon of this product. It is not our intent
to teach you about woodworking. It is assumed that
you are an experienced woodworker with the basic
skills and experience necessary to use this product
safely. If aer reading the following instrucons you
are unsure or uncomfortable about safely using this
product, we urge you to seek addional informaon
through widely available woodworking books or
classes.
As part of our Connuous Product Improvement
Policy, JessEm products are always advancing in
design and funcon. Therefore, there may be
dierences between what is shown in our catalogs,
website or at retail display and what is sold at me
of purchase. We reserve the right to make posive
changes to our products at our discreon.
Assembly Instrucons
1. Place two legs (part #5) on a at surface with the
castor holes facing out on either side (see Figure #3)
and the leveling feet closest to you. Take the front
lower brace (Part #8) and align it with the
corresponding holes as seen in gure #3, ensuring the
ange is oriented correctly. Using four ¼” Washers
and four ¼”-20 x 3/8” Stainless steel Cap Screws (parts
#2 and #4), loosely aach this brace to both legs. Do
not fully ghten the screws at this point. All screws
will be le loose unl the enre stand is built.
Repeat this procedure to mount an upper brace to
both legs (part #3), using the same mounng
hardware as before. At this point you should have one
side assembled, as seen in gure #3.
2. Take the two remaining legs and again lay them in
front of you as done in Step 1. Build the rear leg and
brace assembly the same way as done in Step 1, again
leaving the screws slightly loose.

3. Next, take out the front assembly from Step 1,
and the le and right top braces (Part #1). Using
four ¼” washers and four ¼”-20 x 3/8” Stainless
Steel Cap Screws, mount the upper side braces to
the front assembly. The anges on each brace
should be mounted facing up and inward.
Repeat this process for the le and right boom
braces (part #7), again using four of the 1/4”-20 x
3/8” stainless steel cap screws (part #4) and four
1/4” stainless steel washers (part #2).
All screws should sll be slightly loose at this point.
4. Take the rear leg and brace assembly from Step 2
and use the remaining eight 1/4”- 20 x 3/8”
stainless steel cap screws (part #4) and eight 1/4”
stainless steel washers (part #2) to enclose the
stand. Once this is complete all bolts on the stand
can be ghtened securely with a 3/16” hex key. Do
not over ghten the screws.
5. If mounng a table top to the stand, leave the
top screws loose unl the table top has been
mounted. Then ghten all screws.
Figure #1
Item #
Part #
Descripon
QTY.
1
S0090-1-C
Upper Side Brace
2
2
F0348
1/4” O.D. x 5/8” I.D. Stainless Steel Washer
32
3
S0090-1-C
Upper Front and Back Braces
2
4
F0559
¼”-20 x 3/8” Stainless Steel Cap Screws
32
5
S0090-1-C
Legs
4
6
S0090-1-C
Lower Back Brace
1
7
S0090-1-C
Lower Side Braces
2
8
S0090-1-C
Lower Front Brace (With JessEm Logo)
1

INDIVIDUAL LEG ASSEMBLY BREAK DOWN
Each Leg comes fully assembled with levellers
Figure #2
Item #
Part #
Descripon
QTY.
9
F0572
5/8”- 18 x 3/8” thick Hex Nut
4
10
S0087-2-C
Leveling Foot Threaded Insert
4
11
M0310
Leveling Foot Assembly
4
Figure #3

OPTIONAL ACCESSORIES (Sold Separately)
Castors
The 05150 Steel Router Stand was designed to be used with the 05151 Steel castor set.
Table Top
The 05150 Steel Router Stand will allow both the JessEm Mast-R Top (le) and Mast-R-Li Excel II (right)
to be mounted with factory predrilled holes (see circled holes below).
JESSEM TOOL LIMITED WARRANTY
All JessEm products are warranted to be free
from defects in material and workmanship. JessEm
will repair or replace any product which upon
inspecon proves to be defecve for a period of (1)
year from dated receipt and proof of purchase. All
warranty claims should be made direct to JessEm
Tool Company. Contact JessEm for a warranty claim
return authorizaon and instrucons to proceed.
The consumer is responsible for shipping costs to
return product to JessEm Tool Company. We will
repair or replace the product at our discreon and
JessEm Tool will return shipment to you at no
charge.
WARRANTY LIMITATIONS
This warranty does not cover:
• Repairs or alteraons made or aempted by anyone
other than JessEm Tool Company or an authorized
JessEm service professional.
• Normal wear and tear
• Abuse, misuse or neglect.
• Improper care or maintenance.
• Connued use aer paral failure.
• Products that have been modied in any way.
• Products used with improper accessories.