jetek pro jts-322dn User manual

1
Economic Intelligent
High Speed Dome
User’s Manual

2
CONTENTS
GENERALITRODUCTION..................................................................................................................3
IMPORTANTSAFETYINSTRUCTIONS...............................................................................................................5
CHAPTER1INTRODUCTION.......................................................................................................5
1.1INTRODUCTION...................................................................................................................................5
1.2PICTURES...........................................................................................................................................5
1.3FEATURES...........................................................................................................................................6
1.4TECHNICALDATA.................................................................................................................................7
CHAPTER2INSTALLATIONANDCONNECTION...............................................................................9
2.1OPTIONALPA RTS FORINSTALLATION........................................................................................................9
2.2WARNING........................................................................................................................................9
2.3PREPARATION...................................................................................................................................9
2.4INSTALLATION.................................................................................................................................10
2.5SETTING........................................................................................................................................13
CHAPTER3SETTINGS..................................................................................................................17
3.1KEYBOARDCONTROLLER.....................................................................................................................17
3.2SELF‐CHECKINGINFORMATION.............................................................................................................17
3.3OSDMENUTREE..............................................................................................................................17
3.4MOTION........................................................................................................................................19
3.5DOMESETTING.............................................................................................................................26
3.6CAMERA........................................................................................................................................30
3.7WORKINGSETUP...............................................................................................................................31
3.8RESTART........................................................................................................................................37
3.9FACTORYDEFAULTS.......................................................................................................................37
3.10HELPANDEXIT................................................................................................................................38
APPENDIX.....................................................................................................................................39
APPENDIX1：LIGHTNINGANDSURGEPROTECTION.......................................................................................39
APPENDIX2：RS485GENERALKNOWLEDGE..............................................................................................39

3
GENERALITRODUCTION
Notice
Do not dismantle the
machine to avoid
electric shock
Notice：To avoid electric shock, do not remove the dome cover. Users are not capable of fixing
any internal components.
Only qualified personnel are allowed to do the maintenance.
This label indicates risk of electric shock inside the dome.。
This label is to remind of important manual inside.
Warning
zTo prevent fire or damage caused by electric shock, do not put product on the water or
moisture.
zTo prevent personal injury, equipment must be installed on a solid wall or ceiling bracket.
Please refer to installation instructions.
Warning
1Please use adapters meeting the requirements. Other adapter could cause fire, electric shock
or product damage.
2Wrong power connection may cause fire, electric shock or product failure.
3Prohibition of simultaneous connections of multiple cameras to a single adapter, and capacity
overload of the adapter may cause abnormal heat and fire.
4Power cord should be firmly plugged into a power socket (unstrung connection may cause a
fire)
5The camera should be mounted firmly fixed on a wall or ceiling. Falling camera may cause
personal injury.
6Do not place the conductor (such as: screwdrivers, coins or metal objects) or a container full
of water on top of the camera。

4
7Do not install the unit in humid, dusty or smoky places may cause fire or electric shock. This
could avoid fire, electric shock or personal injury caused by falling objects.
8If the device has abnormal smell or smoke, please stop using the product. You should
immediately unplug the power and service center. If you continue to use at this time may
cause fire or electric shock
9If the product working improperly, please contact the dealer or the nearest service center. Do
not disassemble or in any way to change this product. (Due to an unauthorized user to
disassemble or repair the problems caused within the warranty does not cover
10 While cleaning, do not splash water droplets directly on the product components. (Doing so
may cause fire or electric shock)
11 Do not place the product opposite the air flow position. Otherwise, the temperature difference
between inside and outside will cause moisture condensation within the dome。
12 If you install the product in cold area (such as cold storage), it must be sealed with silicone
wire leads, prevent the outside air from dome. Otherwise, high humidity air outside may flow
into the machine case, and internal and external temperature differences cause the product to
moisture or water vapor inside.
Notice
1Do not drop objects on the product or the product gets affected. Keep it away from vibration
or magnetic interference.
2Do not install the product at high temperature (over 50 ° C), low temperature (below -50 ° C),
or high humidity, and if doing so would result in fire electric shock。
3If you move the product installed, before moving or reinstall, be sure to turn off the power。
4When a lightning storm, unplug the power plug from the socket, if negligence may result in
fire or damage to the product。
5Avoid direct sunlight or heat source, if negligence may bring the fire
6Installed in a well ventilated place.
7Avoid direct exposure to the camera in a sunny place, otherwise it will undermine the CCD
sensor.
8To prevent the machine from rain or splashing water, do not place vases, containers of liquid
on the machine.
9Due to frequent plugging and unplugging of the power cord, install the device in places easy
for removal. While users operate on the machine, please ensure the plug firmly in the power
outlet in order to ensure stable operation。
10 For storage in high humidity environments, shielding may be moisture inside the dome cover.
Dome cover is required to open, and clean with a soft, dry cloth before installation。
11 Please use the products according to working environment requirement:
Power supply AC24V/2.0A
Communication Interface RS-485
Ambient temperature －35℃～55℃
Environment Humidity <95％（no condesing）
Atmospheric pressure 86～106KPa

5
Important Safety Instructions
zPlease read before using these instructions and follow all instructions and pay attention to all
warnings。
zPlease do not run the machine near water。
zPlease clean the machine with a dry cloth。
zDo not block ventilation openings, and while installing, please note the manufacturer's
instructions。
zPlease do not install near any heat sources such as radiators, stoves or other heating device.
zDo not undermine the safety effect the polarized or grounding-type plug. Polarized plug has
two lugs, and one is wider than the other. Grounding type plug has two ground sheets and a
grounding pin. Wide line or grounding-type pin lugs are used to protect your personal safety.
If the provided plug does not fit into your outlet, contact your electrician replace the obsolete
outlet。
zDo not step on or squeeze the power cord, and please pay special attention to protect plugs,
convenience outlets and equipment contact position。
zPlease use the manufacturer's recommended additional equipment or accessories。
zUse only delivery vehicle, foot, tripod, bracket, or table specified by the manufacturer or sold
with the equipment. With carrying car, be careful not to overturn while moving the device。
zDuring lightning storms or unused for long periods, please unplug the device plug。
Chapter 1 Introduction
1.1 Introduction
This speed dome with all-in-one design，simultaneous conveyor belt and accurate stepper motor
enables accurate and steady working；All sorts of installation modes for different places；All
weather proof outdoor design, double deck optional，built-in heater with intelligent start；multiple
surveillance methods，such as scan、cruising、pattern tour；integrated with guard location function，
3D positioning function to make it more powerful.
1.2Pictures
Wall-mount Installation In-ceiling Mount Installation

6
1.3Features
OSD Menu
Support Chinese and English OSD menu, and can display the speed dome information and
status, also can setup speed dome functions and features.
Soft Address
Support soft address function. Soft address can be set in OSD menu, and speed dome can be
controlled by keyboard and PC software with different soft address.
Multi Protocol
Support Pelco_P and Pelco_D protocol
Focus/Rotation speed auto match
Support automatically adjusts PTZ’s horizontal and vertical speed according to the focus
close/far, which will make it easier for manual subject tracking.
Dome address setup
Support 255 camera address，and it only responds to the control instructions consistent with its
address. Use code switch on the dome decoder board to make address setup.
Set and call preset position
Preset position is to store the present PTZ’s horizontal angle, vertical angle and camera focus，
and when it is needed, camera can call these parameters to rotate the camera to this position.
Operator can use keyboard to call preset positions and 220 preset positions are supported.
Auto Scan
Operator can use the keyboard to set left/right boundary to let the dome rotate between left and
right boundary at the preset speed。This dome supports 4 auto scan.

7
Auto Cruising
By programming，dome can list some preset positions as to a certain sequence，and operator
can use a keyboard to control dome to carry on the cruising and rotate between preset positions。
Each cruising can store up to 32 preset positions.
Pattern Tour (PATTERN)
This dome can continuously record 60 seconds’ moving track, and when the pattern is
activated, dome will perform the surveillance according to the recorded tracking.
Guard Location Function
Dome can rotate to the preset position after a period of vacancy. Vacancy time is up to user’s
setup.
Password Protection Function
After start this function, it can set password,
Lens Control
Zoom control and focus control
1.4 Technical Data
1.4.1 Technical Parameters of the High-speed Dome
Model JTS-322DN High Speed Dome Camera
Power Supply AC24V/2.5A
Operating Temperature -35 °C—60°C
Operating moisture < 95%
Power Consumption 50W
Communication RS-485 bus,
Communication transmission speed 2400/4800/9600BPS
Protocols Pelco-D, Pelco-P Compatible
Pan Rotation 0.01°-180° /s
Tilt Rotation 0.01° -120° /s
Pan/Tilt Accuracy +/- 0.07°
Preset Speed 500° /s
Pan Angle 360° Continuously
Tilt Angle 90°
Size 364 x 350 x 202mm
Weight 5.6kg
Preset Positions 220
Auto Scan 8 Groups
Cruise Track 8 Groups
Cruise Points Qty per cruise group 32 Preset Positions
Pattern Tours 4 Groups
Alarm 6 alarm inputs and 2 outputs
Privacy Zone 8 zones

8
Protection IP66 water proof/3000V lightning proof
Fan, Heater Fan and heater auto-starts 24VAC
1.4.2 Camera Parameter for High-speed Dome
Sub Model JTS-322DN
Sensor 1/4’’ Sony Super HAD CCD
Horizontal Resolution 540TVL
Focus Length F=4mm-88mm
Optical Zoom 22X
Digital Zoom 10X
Minimum Illumination 0.11Lux/0.011Lux
Video Output 1Vp-p75ohms
Focus Auto/Manual
Iris Auto/Manual
S/N Ratio ≥50dB
Electric Shutter 1/50~1/10000s

9
Chapter 2 Installation and Connection
2.1 Optional parts for installation
Pedant mount bracket for pedant mounting
Pedant mount bracket（TC-DF12）for ceiling mounting
2.2 Warning
1Select place which can afford four times weight more that speed dome.
2Prevent others closely to avoid causing injuries while installation.
3Move other precious away before installation.
4Power supply is AC220V, please do not charged operation.
2.3 Preparation
(1) 1、Bore 4 holes by using templates included on the wall. Mount 4 expansion screws into the
holes.
2、Please prepare the necessary tools according to specific situations

10
2.4 Installation
1. Get the foam out of the carton
Note：Please protect camera and dome base, make sure the foam is removed from
the carton vertically and slowly, otherwise may lead to damage on camera.
2、Please refer to chapter 2.5<Initial Settings> for Dip Switch Settings
3、Point the gap at the waist-hole, and then use a cross screwdriver to install two
stainless steel screws M4 × 6. Note avoid anything touch the transparent cover,
please protect the transparent cover.

11
4、As is shown by the picture, thread the power cable, video cable,RS-485data cable
through the bracket, push speed dome into bracket connection, and tighten 3 internal
hexagon screws
5、Cable connection
6. Put the cables (including power, video cable, RS 485 and ground line) through the bracket.
Then fix the dome base and the bracket with 4 screws and lock with ￠8 plain cushion and
nut.
Note: Put the bracket away from line and make sure fixed of nut. If dome
installed in outside, please pay more attention on waterproof.

12
Size of wall mount：
Size of in-ceiling mount：
Note: The thickness of ceiling should be between 4.2cm to 0.8cm.And the ceiling
should support 20kg within 225mm diameter.

13
2.5 Setting
Dome Address
Use SW1 to set dome address. Dome setting adopts binary system, the 8th bit is the highest, the
1st bit is the lowest. Total 255 dome addresses could be set.
Note：
1、 Put the dial to “ON”, and “1” means “on” status and “0” means “off” status.
2、 Dip switch for protocol PELCO-P and TIANDY supports maximum 255 dome addresses;
protocol PELCO-D supports maximum 254 dome addresses.
3、 Protocol setting
This product supports three protocols: TIANDY、PELCO-P、PELCO-D, and three baud rate:
9600BPS, 4800BPS, 2400BPS. Protocol dip switch is bit 1~3 of SW2.
1 2 3 4 5 7 8
ON
OFF
Agreement 1 bit 2 bit 3 bit
TIANDY 0 0 0
PELCO-P 1 0 0
PELCO-D 0 1 0
Reserved …… …… ……
*Notice: The factory default protocol is PELCO_P
Baud Rate Setting
Baud rate setting dip switch is bit 4~5 of SW2, and factory default is 9600bps.
1 2 3 4 5 7 8
ON
OFF

14
Baud Rate 4bit 5bit
9600bps 0 0
4800bps 1 0
2400bps 0 1
Preset 1 1
4、 Dome address code table under protocol TIANDY/PELCO-P:
Address PIN1 PIN2 PIN3 PIN4 PIN5 PIN6 PIN7 PIN8
1 0 0 0 0 0 0 0 0
2 1 0 0 0 0 0 0 0
3 0 1 0 0 0 0 0 0
4 1 1 0 0 0 0 0 0
5 0 0 1 0 0 0 0 0
6 1 0 1 0 0 0 0 0
7 0 1 1 0 0 0 0 0
8 1 1 1 0 0 0 0 0
9 0 0 0 1 0 0 0 0
10 1 0 0 1 0 0 0 0
11 0 1 0 1 0 0 0 0
12 1 1 0 1 0 0 0 0
13 0 0 1 1 0 0 0 0
14 1 0 1 1 0 0 0 0
15 0 1 1 1 0 0 0 0
16 1 1 1 1 0 0 0 0
17 0 0 0 0 1 0 0 0
18 1 0 0 0 1 0 0 0
19 0 1 0 0 1 0 0 0
20 1 1 0 0 1 0 0 0
21 0 0 1 0 1 0 0 0
22 1 0 1 0 1 0 0 0
23 0 1 1 0 1 0 0 0
24 1 1 1 0 1 0 0 0
25 0 0 0 1 1 0 0 0
26 1 0 0 1 1 0 0 0
27 0 1 0 1 1 0 0 0
28 1 1 0 1 1 0 0 0
29 0 0 1 1 1 0 0 0
30 1 0 1 1 1 0 0 0

15
31 0 1 1 1 1 0 0 0
32 1 1 1 1 1 0 0 0
… … … … … … … … …
254 1 0 1 1 1 1 1 1
255 0 1 1 1 1 1 1 1
Comparison chart of the PELCO-D protocol address.
Address PIN1 PIN2 PIN3 PIN4 PIN5 PIN6 PIN7 PIN8
1 1 0 0 0 0 0 0 0
2 0 1 0 0 0 0 0 0
3 1 1 0 0 0 0 0 0
4 0 0 1 0 0 0 0 0
5 1 0 1 0 0 0 0 0
6 0 1 1 0 0 0 0 0
7 1 1 1 0 0 0 0 0
8 0 0 0 1 0 0 0 0
9 1 0 0 1 0 0 0 0
10 0 1 0 1 0 0 0 0
11 1 1 0 1 0 0 0 0
12 0 0 1 1 0 0 0 0
13 1 0 1 1 0 0 0 0
14 0 1 1 1 0 0 0 0
15 1 1 1 1 0 0 0 0
16 0 0 0 0 1 0 0 0
17 1 0 0 0 1 0 0 0
18 0 1 0 0 1 0 0 0
19 1 1 0 0 1 0 0 0
20 0 0 1 0 1 0 0 0
21 1 0 1 0 1 0 0 0
22 0 1 1 0 1 0 0 0
23 1 1 1 0 1 0 0 0
24 0 0 0 1 1 0 0 0
25 1 0 0 1 1 0 0 0
26 0 1 0 1 1 0 0 0
27 1 1 0 1 1 0 0 0
28 0 0 1 1 1 0 0 0
29 1 0 1 1 1 0 0 0

16
30 0 1 1 1 1 0 0 0
31 1 1 1 1 1 0 0 0
32 0 0 0 0 0 1 0 0
… … … … … … … … …
253 1 0 1 1 1 1 1 1
254 0 1 1 1 1 1 1 1

17
Chapter3 Settings
Connect the camera to the control device or control software. control device,
including controlling keyboards and hard disk recorders, and control software, which
designed for the clients, can be used to change camera settings. See also the user
manual to grasp the specific operations.
3.1 Keyboard Controller
Follow the following steps to use the controller setting the camera menu.
1Call the preset position No.95, open the camera setting screen.
2Use the stick to browse the menu.
3Press the “Iris on” button to open the menu; One can also use the stick to open this menu.
4Use the stick to change chosen parameters.
5Press the button “Iris on” to apply the change.
3.2 Self-Checking Information
The dome camera operates self-checking moves after being set up a electric circuit. First
horizontally, then vertically, at last the camera-moves. The starting up image would be shown on
the screen after the self-checking moves are done, which vanishes 30 seconds after the start-up.
Horizontal Moves: The dome camera moves downwards to the vertical direction, then upwards to
the preset position before it was set up to the electric circuit.
Vertical Moves: The dome camera moves downwards to the vertical direction, then upwards to the
position before it was set up to the electric circuit.
Camera-moves: Limit-zoom-out the camera lens, then returns and stays at the zoom multiple
before it was set up to the electric circuit.
3.3 OSD Menu Tree

18
LANGUAGE: ENGLISH
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
<CAMERA>
<MOTION>
RESTART
FACTORY DEFAULTS
HELP
EXIT
MAIN MENU
――――――――――――――
SYSTEM INFORMATION
――――――――――――――
DOME ID : 0 1 2 3 4 5 6 7 8 9
ADDRESS : 0 0 1
BAUDRATE : 9600,N,8,1
PROTOCOL : TIANDY
TEMP : 31℃
ALARM : 000000 00
<OTHER>
BACK
EXIT
DISPLAY
DOME :OFF
PRESET :OFF
MOTION :OFF
ZONES :OFF
DATE/TIME :OFF
PAN/TILT :OFF/2SEC/5SEC/10SEC
ALARM :OFF
<DISPLAY POSITION>
BACK
EXIT
――――――――――――――
DOME SETTINGS
<IDLE>
<ALARM>
<AUX>
<PRIVACY MASK>
<CLOCK>
<PASSWORD>
<DOME TITLE>
<OTHERS>
BACK
EXIT
――――――――――――――
CAMERA SETTING
AUTO FOCUS : OFF
DIGITAL ZOOM : OFF
BACKLIGHT : OFF
IMAGE FREEZE : OFF
ZOOM SPEED : LOW/ NORMAL/HIGH
DAY NIGHT : AUTO/BW/COCLOR
<ADVANCED>
BACK
EXIT
――――――――――――――
MOTION
<PRESET>
<SCAN>
<SEQUENCE>
<PATTERN>
<ZONES>
<TIMING ACTION>
<AUTO TRACKING>
BACK
EXIT
――――――――――――――

19
3.4 MOTION
A
B
C
D
E
F
G
LANGUAGE: ENGLISH
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
<CAMERA>
<MOTION>
RESTART
FACTORY DEFAULTS
HELP
EXIT
MAIN MENU
――――――――――――――
MOTION
<PRESET>
<SEQUENCE>
<PATTERN>
<ZONES>
<TIMING ACTION>
<AUTO TRACKING>
BACK
EXIT
――――――――――――――
<SCAN>
A. PRESET
A1
B1
C1
D1
E1
MOTION
<SEQUENCE>
<PATTERN>
<ZONES>
<TIMING ACTION>
<AUTO TRACKING>
BACK
EXIT
――――――――――――――
<SCAN>
<PRESET>
PRESET
TITLE : PRESET 01
CALL
<SET>
DELETE
BACK
EXIT
――――――――――――――
PRESET NO. : 001
――――――――――――――
A1. PRESET NO.
Move the cursor to PRESET NO.，press the key IRIS ON(key on control keyboard) to enter the
edition mode of preset No., move the joystick upward and downward to select number. Then press
IRIS ON to confirm.

20
B1. TITLE
Move the cursor to TITLE and press IRIS ON to enter the edition mode of preset title.
C1.CALL
MOVE the cursor to CALL and press IRIS ON to call upon the current preset position.
D1.SET
Move the cursor to SET and press IRIS ON the enter preset setting mode. Then the sentence
“PRESS IRIS ON TO CONFIRM”will appear on the screen. Move the joystick to do PTZ move
and press IRIS ON to confirm the preset you want.
E1.DELETE
Move the cursor to DELETE and press IRIS ON to delete the current preset position.
B.SCAN
A1
B1
C1
D1
E1
MOTION
<SEQUENCE>
<PATTERN>
<ZONES>
<TIMING ACTION>
<AUTO TRACKING>
BACK
EXIT
――――――――――――――
<SCAN>
<PRESET>
SCAN
TITLE : SCAN 1
<LEFT LIMIT>
<RIGHT LIMIT>
SCAN SPEED : 20
BACK
EXIT
――――――――――――――
SCAN NO. : 01
――――――――――――――
START
F1
A1.SCAN NO.
Move the cursor to SCAN NO. and press the key IRIS ON(key on control keyboard) to enter the
edition mode of scan No., move the joystick upward and downward to select number. Then press
IRIS ON to confirm.
B1. TITLE
Move the cursor to TITLE and press IRIS ON to enter the edition mode of scan title.