Johnson Controls Unitary Products EB Series User manual

Johnson Controls Unitary Products 5393776-BIM-B-0817
ELECTRIC FURNACE
MODELS: EB*/EU*
Downflow/Upflow
INSTALLATION MANUAL
®
For Installation In:
1. Manufactured (Mobile) Homes
2. Recreational Vehicles & Park Models
3. Modular Homes & Buildings
LIST OF SECTIONS
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
UNIT INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
ELECTRIC FURNACE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . .4
THERMOSTAT INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
OPTIONAL AIR CONDITIONING ACCESSORIES . . . . . . . . . . . . . . 9
WIRING DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
LIST OF FIGURES
Furnace Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Alcove & Closet Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Upflow Closet Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Duct Connector Depth (7990 Series) . . . . . . . . . . . . . . . . . . . . . . . . . .4
Duct Connector Dimensions (7990 Series) . . . . . . . . . . . . . . . . . . . . .4
Recommended Floor Cut-out (7990 Series) . . . . . . . . . . . . . . . . . . . .4
Duct Connector Screw Attachment (7990 Series) . . . . . . . . . . . . . . . .5
Duct Connector Tab Attachment (7990 Series) . . . . . . . . . . . . . . . . . .5
Installation of Furnace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Field Wiring Shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Control Box 7
Thermostat Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Thermostat Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
EB/EU10* Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
EB/EU12* Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
EB/EU15* Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
EB/EU17* Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
EB/EU20* Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
EB/EU23* Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
LIST OF TABLES
Duct Connector for Electric Furnaces . . . . . . . . . . . . . . . . . . . . . . . . .4
Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 EB/EU Series Blower Performance . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Physical and Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SECTION I: GENERAL
The following list includes important facts and information regarding the
EB/EU furnace and its packaging inclusions:
1. Furnace is rated at 240 volts, 60 Hz, single phase.
2. Filters are furnished with EB model, and are the same for all EB
models - 16 x 20 x 1 in top and 20 x 20 x 1 in the louvered door.
3. Furnace size is the same for all models. See Figure 1.
4. Four-wire thermostat operation for heating and cooling.
5. Coil cavity built into furnace (coil shelf accessory required for EB
model).
6. All furnaces are equipped with an air conditioner blower and isA/C
or Heat Pump ready (coil shelf accessory required for EB model).
7. Holding strap furnished on top rear of furnace.
8. The EB furnace is designed for downflow application, and the EU
furnace is designed for upflow application.
9. This furnace must not be operated without the front panel
installed. NOTICE
This furnace and its components listed on the A/C and Heat Pump
equipment sticker are listed in combination as a system by Under-
writer's Laboratories for the United States and Canada. FIGURE 1: Furnace Dimensions
´
´
237,21$/%27720),(/'
:,5,1*(175<
$
%
&
'
(
)
+
*
-
.
/
0
1
´
´
´
´
´
´
´
´
´
´
´
´
´
-
+
&%$'
()*
1
0
/
.
68%%$6(,)
86('$''6
´025(72
727$/+(,*+7
$1'´72
:,'7+
7+(50267$7
:,5,1*
(175<
),(/'
:,5,1*
(175<
$
´

5393776-BIM-B-0817
2 Johnson Controls Unitary Products
SECTION II: SAFETY
This is a safety alert symbol. When you see this symbol on
labels or in manuals, be alert to the potential for personal
injury.
Understand and pay particular attention to the signal words DANGER,
WARNING, or CAUTION.
DANGER indicates an imminently hazardous situation, which, if not
avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation, which, if not
avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation, which, if not
avoided may result in minor or moderate injury. It is also used to
alert against unsafe practices and hazards involving only property dam-
age.
1. Install this electric furnace only in a location and position as speci-
fied in SECTION III of these instructions.
2. Always install the electric furnace to operate within the electric fur-
nace’s intended maximum outlet air temperature. Only connect the
air handler to a duct system which has an external static pressure
within the allowable range, as specified on the EB/EU rating plate.
3. When an electric furnace is installed so that supply ducts carry air
circulated by the air handler to areas outside the space containing
the air handler, the return air shall also be handled by duct(s)
sealed to the air handler casing and terminating outside the space
containing the air handler.
4. The electric furnace is not to be used for temporary heating of
buildings or structures under construction.
5. The size of the unit should be based on an acceptable heat loss or
gain calculation for the structure. ACCA, Manual J or other
approved methods may be used.
SAFETY REQUIREMENTS
1. This electric furnace should be installed in accordance with all
national and local building/safety codes and requirements, local
plumbing or wastewater codes, and other applicable codes.
2. Refer to the unit rating plate for the EB/EU model number, and
then see the dimensions page of this instruction for supply air ple-
num dimensions in Figure 3. The plenum must be installed accord-
ing to the instructions.
3. Provide clearances from combustible materials as listed under
Clearances to Combustibles.
4. Provide clearances for servicing ensuring that service access is
allowed for electric furnace elements and blower.
5. Failure to carefully read and follow all instructions in this manual
can result in electric furnace malfunction, death, personal injury
and/or property damage.
6. Check the rating plate and power supply to be sure that the electri-
cal characteristics match.
7. Electric furnace shall be installed so the electrical components are
protected from water.
8. Installing and servicing heating/cooling equipment can be hazard-
ous due to the electrical components. Only trained and qualified
personnel should install, repair, or service heating/cooling equip-
ment. Untrained service personnel can perform basic maintenance
functions such as cleaning and replacing the air filters. When
working on heating/cooling equipment, observe precautions in the
manuals and on the labels attached to the unit and other safety
precautions that may apply.
9. These instructions cover minimum requirements and conform to
existing national standards and safety codes. In some instances
these instructions exceed certain local codes and ordinances,
especially those who have not kept up with changing residential
and non-HUD modular home construction practices. These
instructions are required as a minimum for a safe installation.
INSPECTION
As soon as a unit is received, it should be inspected for possible dam-
age during transit. If damage is evident, the extent of the damage
should be noted on the carrier’s freight bill. A separate request for
inspection by the carrier’s agent should be made in writing.Also, before
installation the unit should be checked for screws or bolts, which may
have loosened in transit. There are no shipping or spacer brackets
which need to be removed.
Also check to be sure all accessories such as heater kits, suspension
kits, and coils are available. Installation of these accessories or field
conversion of the unit should be accomplished before setting the unit in
place or connecting any wiring, electric heat, ducts or piping.
CODES
The electric furnace must be installed in accordance with the following
codes:
• Standard for the Installation of Air Conditioning and Ventilating
Systems (NFPA 90A)
• Standard for the Installation of Warm Air Heating and Air Condi-
tioning Systems (NFPA 90B)
• National Electric Code (NFPA 70)
• Canadian Electrical Code, Part I (CSA C22.1)
• All local codes (state/county/township).
WARNING
Improper installation may create a condition where the operation of
the product could cause personal injury or property damage.
Improper installation, adjustment, alteration, service or mainte-
nance can cause injury or property damage. Refer to this manual
for assistance or for additional information, consult a qualified con-
tractor, installer or service agency.
CAUTION
This product must be installed in strict compliance with the installa-
tion instructions and any applicable local, state, and national codes
including, but not limited to building, electrical, and mechanical
codes.
WARNING
FIRE OR ELECTRICAL HAZARD
Failure to follow the safety warnings exactly could result in serious
injury, death or property damage.
A fire or electrical hazard may result causing property damage, per-
sonal injury or loss of life.
!
!
!
NOTICE
All applicable codes take precedence over any recommendation
made in these instructions.

5393776-BIM-B-0817
Johnson Controls Unitary Products 3
SECTION III: UNIT INSTALLATION
LOCATION
Access for servicing is an important factor in the location of any furnace.
Provide a minimum of 24” (61 cm) in front of the furnace for access to
the heating elements and controls. This access may be provided by a
closet door or by locating the furnace 24” (61 cm) from a facing wall or
partition.
FURNACE CLEARANCE
This furnace is approved for zero (0) inch clearance to combustible
material on all or any part of the furnace exterior and the inlet or outlet
duct work except as stated below.
For furnaces installed in upflow application, there must be a minimum
of 1” (2.54 cm) clearance from the bare surface of the outlet duct work
for a distance of 3 feet (91.4 cm) from the supply air opening. This
requirement is met if the duct is wrapped with an insulating material at
least 1” thick and having an R-value of at least R-4.
RETURN AIR
In order for the furnace to work properly, a closet or alcove must have a
certain total free area opening for return air.
For Heating Only Furnace
Minimum 200 sq. in (1290 sq. cm) free area opening. Use any return
Grille with minimum 200 sq. in. free opening.
For up to 4 Ton AC and 3.5 Ton HP Applications (Standard
Blower)
Minimum 250 sq. in. (1613 sq. cm) free area opening. The standard
blower assembly supplied with the furnace is capable of handling up 4
Ton AC and 3.5 Ton HP applications. Use any return grille with mini-
mum 250 sq. in. (1613 sq. cm) free area opening.
For 5 Ton AC and 4 Ton HP Applications (Accessory
Blower)
Minimum 350 sq. in (2129 sq. cm) free area opening. Use 5 Ton AC/4
Ton HP blower accessory 3500-7901/A. Use accessory louvered door
3501-9311 or any return grille with a minimum 350 sq. in. (2129 sq. cm)
free area opening.
Location
The return air opening can be located in a closet front door or a side-
wall above the furnace casing, or in a louvered door on the furnace. If
opening for the return air is located in the floor, side walls or closet
door anywhere below furnace casing height, 6” (15.2 cm) minimum
clearance must be provided on the furnace side where return is
located to provide for proper air flow. See Figure 2. The 6” (15.2 cm)
minimum clearance is not required if there is a return grille installed
above the furnace height. This return grille cannot start more than
three feet above the furnace height. If the louvers in the closet door
have as much air flow area as the EB louvered furnace door, only 1”
clearance is required.
For Upflow installations, a closet 32” (81.3 cm) wide by 30” (76.2 cm)
deep with a 30” (76.2 cm) wide door is necessary. See Figure 3. This is
not required if there is a return grill installed below the furnace.
When installing furnace in a separate closet or room which is accessi-
ble only through an outside door, a minimum of 200 in2(1290 cm2) free
opening for return air must be provided. The supply and return air must
be ducted, securely attached and be sealed to the furnace casing if
there are grilles in the outside door to the closet. Openings where ducts
pass through walls, the floor or the ceiling must be sealed to prevent air
leakage into or from closet and the living area.
Provisions shall be made to permit the return of circulating air from all
rooms and living spaces, except the bathroom(s) to the circulating air
supply inlet of the furnace. Failure to comply may cause improper heat-
ing and may cause the furnace to cycle on the limit.
DUCT SYSTEM DESIGN
Electric furnace is designed to operate at a given static pressure.
In order to assure proper air flow through the furnace, the distribution
system must be designed so that the static pressure external to the fur-
nace does not exceed the static pressure rating shown on the furnace
rating plate.
The number, size and placement of registers should be such that even
distribution of heat is provided throughout the home.
FIGURE 2: Alcove & Closet Clearances
FIGURE 3: Upflow Closet Clearances
´0,1
´
´
´0,1
7KHUHPXVWEHDWOHDVW
IHHWRIVSDFHDYDLODEOH
LQIURQWRIIXUQDFHIRU
VHUYLFLQJWKHIXUQDFH
ZKHQQHFHVVDU\
$LQFKFOHDUDQFHLV
UHTXLUHGLIWKHVSDFH
EHWZHHQIXUQDFHDQG
HQFORVXUHLVXVHGIRU
UHWXUQDLU
$
´
´
´
:,'('225 &/26(7
´23(1,1*:,'7+
5HWXUQDLU
SDVVWKURXJK
IUDPHZLGWK
´0,10$;
$
127(
0LQLPXPUHTXLUHGVTXDUH
LQFKRSHQLQJGLFWDWHVWKH
KHLJKWRIWKHUHWXUQDLU
RSHQLQJDVGLVFXVVHG
HDUOLHULQWKHVHFWLRQ

5393776-BIM-B-0817
4 Johnson Controls Unitary Products
SECTION IV: ELECTRIC FURNACE
INSTALLATION
7900 SERIES DUCT CONNECTOR FOR EB DOWN-
FLOW
The duct connector is designed to eliminate a sub-base requirement.
Table 1 provides the part number of the duct connector needed.
Provide adequate clearance for servicing.
1. Locate furnace conveniently away from wall facing or partitions to
permit easy removal of components.
2. A six (6) inch space minimum should be maintained between the
furnace and closet door when door is used for return air.
3. Two (2) feet of space must be available in front of furnace for
future servicing (blower, element or furnace removal, etc.).
 - Indicates connector above or below could be used depending on tolerance
in floor to duct dimension.
 - Indicates connector above could be used depending on tolerance in floor
to duct dimension.
 - Indicates connector below could be used depending on tolerance in floor to
duct dimension.
DUCT CONNECTORS (7990 SERIES)
These duct connectors are for connecting the furnace to an under the
floor supply duct system. The furnace may be installed on combustible
flooring without a separate sub-base.
TABLE 1:
Duct Connector for Electric Furnaces
FLOOR TO
DUCT DIMENSIONS FINGERED STYLE SCREW TAB STYLE
1” (2.54 cm) 7990-6211 7990-6011
2” (5.1 cm) 7990-6221 7990-6021
3” (7.6 cm)  
4” (10.2 cm) 7990-6241 7990-6041
5” (12.7 cm)  
6” (15.2 cm) 7990-6261 7990-6061
7” (17.8 cm) 7990-6271 7990-6071
8” (20.3 cm) 7990-6281 7990-6081
9” (22.8 cm)  
10” (25.4 cm) 7990-6301 7990-6101
11” (282 cm)  
12” (30.5 cm) 7990-6321 7990-6121
13” (33 cm)  
FIGURE 4: Duct Connector Depth (7990 Series)

'8&7&211(&725
'(37+
)/225
)/225
-2,67
6833/<'8&7
$
FIGURE 5: Duct Connector Dimensions (7990 Series)
FIGURE 6: Recommended Floor Cut-out (7990 Series)



 6HH
&KDUW





'8&7&211(&7256)25
6&5(:$77$&+0(17

$



 6HH
&KDUW

'8&7
&87287
',0(16,216
'8&7&211(&7256)25
7$%$77$&+0(17





$

 0,1




 







5($5:$//
2)(1&/2685(
&(,/,1*&87287
)25522)-$&.
)/225&87287
)25'8&7
&211(&725
)851$&(
287/,1(
237,21$/
(/(&75,&
(175$1&(
)/225
)8785(
5()5,*(5$17
/,1((175$1&( $

5393776-BIM-B-0817
Johnson Controls Unitary Products 5
INSTALLATION OF SCREW ATTACHMENT DUCT
CONNECTOR (7990 SERIES)
1. Make floor cut out as shown in Figure 6.
2. Determine the depth of the floor cavity from the surface of the floor
to the top of the supply air duct and select the appropriate duct
connector from the chart.
3. Place locating bracket (supplied with the duct connector) to the
back edge of the floor opening. See Figure 7.
4. Apply a water based duct sealant to the 1/2” supply duct attach-
ment flange of the duct connector.
5. Determine which of the four positions the duct connector best cen-
ters over the supply duct and insert it through the floor cutout.
6. When properly aligned with the supply duct, secure the duct con-
nector to the floor with nails, flat head screws or staples.
7. Use screws as required to secure duct connector to supply duct.
8. Cut out the opening to the supply duct. If sealant was not used, the
installer should tape the mating flanges to provide a good air seal.
INSTALLATION OF TAB ATTACHMENT DUCT
CONNECTOR (7990 SERIES)
1. Make floor cut out as shown in Figure 6.
2. Determine the depth of the floor cavity from the surface of the floor
to the top of the supply air duct and select the appropriate duct
connector from the chart.
3. Place locating bracket (supplied with the duct connector) to the
rear of the floor area for the furnace. See Figure 8.
4. Determine which of the four positions the duct connector best cen-
ters over the supply duct and insert it through the floor cutout.
5. Mark cut-out location on the supply duct and remove the duct con-
nector.
6. Cut out the opening to the supply duct.
7. Bend tabs down through and back up under the supply duct.
8. Secure the duct connector to the floor with nails, flat head screws
or staples.
The duct connector is designed for use on ducts down to 12" in width.
When using the connector on smaller width ducts, there is not sufficient
clearance to bend the tabs on two sides of the duct connector.
In such cases the tabs may be attached to the sides of the duct by
using sheet metal screws or other suitable fasteners. Holes for sheet
metal screws are provided in three (3) tabs on each side of the duct
connector. If more than 3 tabs need to be used to provide a more
secure and air tight connection, the remaining tabs can also be fas-
tened to the duct with screws after drilling the required screw holes.
INSTALLATION OF THE FURNACE
1. Remove the front panels and set the furnace onto the duct con-
nector. Slide it back until the rear of the unit engages the locator
bracket.
2. Secure the front of the furnace with two screws at the provided
mounting holes. See Figure 10.
3. Secure the top of the furnace to a structural member using screw
through the strap at the top of the furnace. Strap may be moved to
any of the holes located along the top back of the furnace. Installer
may provide an equivalent method, such as screws through the
casing side.
FIGURE 7: Duct Connector Screw Attachment (7990 Series)
NOTICE
Duct sealant and tape must be classified as meeting HUD Standard
3280.715, U.L. Standard 181A.
FIGURE 8: Duct Connector Tab Attachment (7990 Series)
/2&$725%5$&.(7
1$,/6)/$7+($'6&5(:6
2567$3/(6
6&5(:6
)/225
6833/<'8&7
$
/2&$725%5$&.(7
1$,/6)/$7+($'6&5(:6
2567$3/(6
%HQGWDEVXQGHUGXFW
RSHQLQJWRVHFXUHWRWKH
VXSSO\GXFW
)/225
6833/<'8&7 $
FIGURE 9: Installation of Furnace
)XUQDFH6HDWHG
$JDLQVWWKH
/RFDWRU%UDFNHW
6HFXUH)XUQDFH
WR)ORRUZLWK7ZR
1DLOVRU6FUHZV
1RW3URYLGHG
$


5393776-BIM-B-0817
6 Johnson Controls Unitary Products
WIRING
Furnace wiring is complete except for the power supply and the thermo-
stat wires. See wiring diagrams (Figures 15-20) for wire and fuse size.
See Table 2 for ground wire sizes. Thermostat wires connect through
side of furnace and should also be no smaller than 22 gauge. Power
wires can enter through the side of the unit or through the auxiliary
entrance, located in the bottom of the unit. (See Figure 1). When bring-
ing wiring through the bottom of the furnace, cable connectors must be
installed to hold wiring in place and to relieve any strain on the wiring.
These connectors also serve as a seal between the furnace and the
floor. Thus, additional sealing is not required.
Refer to the National Electrical Code, Canadian Electrical Code and
local codes for wiring material requirements.
Models for EB/EU15*, EB/EU17*, EB/EU20*, and EB/EU23* may be
connected to a single or dual branch circuit.
These units are shipped from the factory set up for dual power supply
connections. For single power supply connections, jumper bars (P/N
3500-378P*) are required and are available from the factory. See Fig-
ures 11 and 12.
NOTICE
The furnaces are equipped with either one or two 60 amp circuit
breakers. These circuit breakers protect the wiring inside of the fur-
nace in the event of a short circuit. Additionally, these breakers pro-
vide a means of disconnecting the power to the unit. The circuit
breakers in the furnace are not meant to protect the branch circuit
wiring between the furnace and the home's breaker panel. General
wire and breaker sizes are shown in Table 2. If sheathed cable is
used, refer to National Electrical Code, Canadian Electrical Code
and local codes for additional requirements concerning supply cir-
cuit wiring. Electrical Data can be found in Table 4.
IMPORTANT
All installation on field wiring must be rated at 60ºC or higher.
TABLE 2: Wiring Requirements
MODELS 1EB10F
EU10A
2EB12F
EU12A
3EB15F
EU15A
3EB17F
EU17A
3EB20F
EU20A
3EB23F
EU23A
Single Branch Circuit Service 2 Leads + 1 Ground CKT #1
Nominal Circuit Load - Amps 44.0 50.7 64.0 70.7 84.0 94.0
Minimum Wire Size (90ºC) #8 #6 #4 #4 #3 #2
Minimum Wire Size (75ºC) #6 #6 #4 #3 #2 #1
Minimum Wire Size (60ºC) #6 #4 #3 #2 #1 #0
Ground Wire Size + #10 #8 #8 #8 #6 #6
Max. Fuse (or C.B.) - Amps 60 70 80 90 110 125
Dual Branch Circuit Service
NOT
APPROVED
CKT #1 CKT #2 CKT #1 CKT #2 CKT #1 CKT #2 CKT #1 CKT #2
Branch Circuit Load - Amps 44.0 20.1 47.3 23.4 44.0 40.0 47.3 46.7
Branch Circuit Min. - Amps 55.0 25.2 59.2 29.3 55.0 50.0 59.2 58.4
Minimum Wire Size (90ºC) #8 #10 #6 #10 #8 #8 #6 #6
Minimum Wire Size (75ºC) #6 #10 #6 #10 #6 #8 #6 #6
Minimum Wire Size (60ºC) #6 #10 #4 #10 #6 #6 #4 #4
Ground Wire Size 4#10 #10 #10 #10 #10 #10 #10 #10
Max. Fuse (or C.B.) - Amps 60 30 60 30 60 50 60 60
NOTES:
1. Does Not require a Jumper.
2. Jumper provided for Single Branch Circuit Only.
3. Requires Jumper Bars (P/N 3500-378P).
4. Refer to National Electrical Code (NEC). Table 250-122 for Non-Sheathed Conductor Ground Wire.
TABLE 3: EB/EU Series Blower Performance
Static Pressure (inches of w.c.) 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
Low Speed - Heating Speed
Models EB10, 12, 15 CFM (STD. Air) 945 936 936 924 915 889 870 813 705
Medium Speed - Heating Speed
Models EB17, 20, 23 CFM (STD. Air) 1160 1145 1145 1140 1129 1109 1073 1027 935
Medium High - with A-Coil in place CFM (STD. Air) 1340 1317 1290 1252 1208 1158 1095 1021 876
High - with A-Coil in place CFM (STD. Air) 1573 1534 1490 1435 1369 1309 1237 1135 1019

5393776-BIM-B-0817
Johnson Controls Unitary Products 7
TABLE 4: Physical and Electrical Data
1MODEL NUMBER 2,3EB10F
EU10A
3,4EB12F
EU12A
5EB15F
EU15A
5EB17F
EU17A
5EB20F
EU20A
5EB23F
EU23A
D.O.E.
Output 240 VAC 60 Hz.,1 Phase BTU 34,000 39,000 51,000 56,000 67,000 77,000
kW 10.0 11.4 15.0 16.4 19.6 22.6
OUTPUT
CAPACITY
230 VAC
60 Hz.,1 Phase BTU 31,000 36,000 47,000 52,000 61,000 71,000
kW 9.1 10.6 13.8 15.2 17.9 20.8
220 VAC
60 Hz.,1 Phase BTU 29,000 33,000 43,000 48,000 57,000 65,000
kW 8.5 9.7 12.6 14.1 16.7 19.1
Element Capacity
@ 240 VAC kW 9.6 11.2 14.4 16.0 19.2 21.6
Amps 40.0 46.7 60.0 66.7 80.0 90.0
Motor Amps @ 240 V. 4.0 Maximum
Circuit Load Amps
@ 240 V. CKT 1 44.0 50.7544.0 47.3 44.0 47.3
CKT 2 NA NA 20.0 23.4 40.0 46.7
Filter Size 16 x 20 x 1
Shipping Weights 83 84 85 86 84 86
NOTES:
1. Casing or Cabinet must be permanently grounded in accordance with N.E.C. or other applicable codes.
2. Does Not require a Jumper.
3. Approved for Single Branch Circuit Service Only.
4. Jumper provided fro Single Branch Circuit Only.
5. Requires Jumper Bars (P/N 3500-378P).
WARNING
For personal safety be sure to turn the electrical power OFF at the
household service box and at the furnace circuit breakers before
attempting any service or maintenance operations. Homeowners
should never perform any maintenance which requires opening
electric box door.
Furnace is equipped with a protective shield over field wiring con-
nection. When field wiring is completed, shield must be replaced to
prevent hazard of electrical shock when using furnace disconnect.
(See Figure 11.)
!
FIGURE 10: Field Wiring Shield
&,5&8,7
%5($.(56
(/(&75,&
3$1(/
),(/':,5,1*
3527(&7,9(
6+,(/'
%/2:(5
$
FIGURE 11: Control Box
TRANSFORMER
LIMIT
SWITCHES
GROUND
LUGS
3500-378P* JUMPER
BARS (FOR SINGLE
BRANCH CIRCUIT
SERVICE)
THERMOSTAT
WIRES
CIRCUIT
BREAKERS
SEQUENCERS
NOTE:
As Shipped, the jumper bar assembly
is set up for bottom entry. For side
entry, the top lug can be removed and
re-positioned, as shown, to provide
proper wire bending clearances.
A0345-001
0
6
FFO
NO
N
O
F
FO
06

5393776-BIM-B-0817
8 Johnson Controls Unitary Products
SECTION V: THERMOSTAT
INSTALLATION
The adjustable heat anticipator in the thermostat is pre-set at 0.4 amps.
This setting should be checked at the time of installation.
In some cases the thermostat may be a “self-setting” type in which case
no amp setting is on the thermostat, eliminating the need for any field
adjustment.
Thermostat should be located on an inside wall in an open area to more
closely regulate average room air, preferably, where there is air move-
ment back to furnace. Care should be used to locate thermostat away
from hot air discharge openings, lights, etc. Locating height of thermo-
stat is important. Thermostat should be located 52” to 66” (132 - 167.6
cm) above the floor. This is sometimes called the comfort zone.
If a condenser with its own Transformer shares a Heat/Cool Thermostat
with this furnace, use a thermostat with isolating contacts to prevent
interconnection of Class II 24 Volt Systems.
Cycle furnace using the thermostat to make sure it operates correctly.
Maintenance and operating instructions are in the customer envelope
accompanying the furnace. Give the customer envelope to the home
owner.
CAUTION
When using separate thermostats, a thermostat interlock system
must be provided to prevent simultaneous operation of the furnace
and air conditioner. Simultaneous operation can result in coach
overheating, equipment damage and energy waste. (See Figures
13 and 14.)
Do not connect Yellow wire to thermostat until an outdoor unit is
installed.
FIGURE 12: Thermostat Wiring
!
&22/,1*
7+(50267$7
+($7,1*
7+(50267$7
72
$,5&21',7,21(5
72
)851$&(
'28%/(32/(
'28%/(7+52:6:,7&+
$
FIGURE 13: Thermostat Wiring
'(/8;( %/(1' $,5 ,,
)5(6+
$,5
2))
$872
$/$50
5('
5('
:+,7( :+,7(
*5((1
*5((1
%/$&.
%/$&.
%/$&.
5('
:+,7(
*5((1
<(//2:
:,5(6)520)851$&(
127)$&725<
,167$//('
67$1'$5'25'(/8;(
%/(1'$,5&21752/%2;
7+(50267$7:,5,1*6&+(0$7,&)25%/(1'$,5$1')851$&(
7KH(%(8)XUQDFHVDUH$&UHDG\
$OOIXUQDFHVLQVWDOODWLRQVVKRXOGLQFOXGHDPLQLPXPRIIRXUFRQGXFWRUWKHUPRVWDW
ZLULQJWRDFFRPPRGDWHIXWXUHDLUFRQGLWLRQLQJLQVWDOODWLRQV
)RXUFRQGXFWRUZLUHLVUHTXLUHGIRUWKHUPRVWDWFRQQHFWLRQ
$WWDFKWKHORZYROWDJHZLUHVH[WHQGLQJIURPWKHFRQWURO
ER[DVIROORZV
5('ZLUHIURP)XUQDFHWRWKHUPRVWDW5('ZLUH
:+,7(ZLUHIURP)XUQDFHWRWKHUPRVWDW:+,7(ZLUH
*5((1ZLUHIURP)XUQDFHWRWKHUPRVWDW*5((1ZLUH
%/$&.ZLUHIURP)XUQDFHWRFRQGHQVLQJXQLWFRQWDFWRU
$

5393776-BIM-B-0817
Johnson Controls Unitary Products 9
SECTION VI: OPTIONAL AIR
CONDITIONING ACCESSORIES
EB Furnace Models
The EB furnace is already equipped with a blower and control system
for add-on air conditioning and heat pump. The coil shelf kit (3500-
8981 for downflow coils up to 5 ton or any coil with drain pan longer
than 19-1/2” and 3500-8602 extension cabinet for any coils taller than
19-1/2”) must be installed when adding on remote air conditioning
systems. With the 3500-8981 coil shelf installed in the EB model, the
coil cavity accepts coils no taller than 19-1/2”, no wider than 18-1/4”
and no deeper than 20-1/2”.
EU Furnace Models
No extension cabinet and coil shelf are needed for the EU upflow
furnace. The coil shelf is already installed in the EU models. Like the
above furnace models, the coil cavity accepts coils no taller than 19-1/2”,
no wider than 18-1/4” and no deeper than 20-1/2”.
HIGH PERFORMANCE BLOWER
ACCESSORY PACKAGE
All electric furnaces are equipped with a blower and control system to
add-on air conditioning and heat pumps to specified sizes. If the
requirement is to achieve more air flow or cooling than specified, then
the blower inside the furnace has to be replaced with an accessory
blower package 3500-7901/*. This accessory blower package would
deliver air conditioning up to 5-tons, and heat pump up to 4-tons.
WARNING
Failure to install this insulation and coil shelf kit could result in dam-
age to equipment and/or personal injury. Liability and warranty from
the manufacturer could also be void.
NOTICE
If the controls are located at the top of the unit, the furnace is an
upflow furnace and the airflow is forced up through the furnace and
into the airways.
!CAUTION
All areas around the line sets, drain hoses and other openings in
the coil shelf should be sealed air tight. Use some moldable com-
pound or caulking to seal the area. Failure to do so may result in
loss of performance and premature compressor failure.
!

5393776-BIM-B-0817
10 Johnson Controls Unitary Products
SECTION VII: WIRING DIAGRAMS
FIGURE 14: EB/EU10* Wiring Diagram
IF ANY OF THE ORIGINAL WIRE
SUPPLIED WITH THIS UNIT MUST BE
REPLACED. IT MUST BE REPLACED
WITH TYPE 105 C THERMOPLASTIC
WIRING MUST CONFORM TO LOCAL CODES
BLK
RED
WHT
GRN
BLEND AIR
CONTROL BOX
BLU-MED. HIGH SP.
MOTOR
YEL-MED. LOW SP.
BLK-COOLING SP.
RED-HEATING SP.
2 SPADE (INSUL.)
TERMINALS USED
WHEN
CHANGING
SPEEDS LINE
LOAD
ORG
BRN
CAPACITOR
ORG-COMMON.
TRANSFORMER
BLK
3A
FUSE
RED
RED
BLK
G
W
RH
Y
HEAT/COOL
T'STAT
BLOWER
RELAY
2
4
6
5
1
3
YEL
BLK
M3 M1
M2
H2
SEQUENCER
BLU
YEL
R
R
ELEMENTS
SWITCHES
LIMIT
60 AMP
CIRCUIT #1
BREAKER
ORG
ORG
YEL
ORG
MODEL: EB10F / EU10A
COND. UNIT
CONTACTOR
REPLACE
FILTER
WITH SAME
SIZE
240 VAC - 60 Hz - 1 PHASE
NOTE:
4-SPEED BLOWER
EB / EU SERIES FURNACES
GRN
WHT
M4
H1
YEL
L
L
YEL
YEL
SINGLE BRANCH
CIRCUIT SERVICE
240 VAC.
60Hz
1 PHASE
GND. LUG
DO NOT OPEN THIS PANEL UNTIL ELECTRICAL POWER IS SHUT
OFF AT HOUSEHOLD SERVICE BOX. CHECK WITH A VOLTMETER
OR OTHER PROPER INSTRUMENT.
-HAZARD OF ELECTRICAL SHOCK-
SERVICE CONNECTION COVER MUST BE INSTALLED.
IF FILTERS ARE USED, CLEAN/REPLACE EACH SEASON OR
MORE OFTEN IF NEEDED. 5166485-UWD-B-0617
IMPORTANT -
HIGH VOLTAGE
SHOCK HAZARD
THIS FURNACE MAY BE CONNECTED TO MORE THAN ONE POWER SUPPLY.
TURN OFF ALL POWER TO THE FURNACE AT THE WALL BOX, AND LOCK IT OUT.
6
2
48
1
0
RELAY
BRN
ORG
ORG
ORG
BRN
WARNING
CAUTION
D.O.E. OUTPUT CAPACITY - BTU 34,000
MAX. MOTOR-FLA 4.0
SINGLE BRANCH
CIRCUIT SERVICE
2 LEADS +
1 GROUND
NOMINAL CIRCUIT LOAD-AMPS 44.0
WIRE SIZE (75 C) COPPER #6
WIRE SIZE (60 C) COPPER #6
MAX. FUSE SIZE (OR CB) - AMPS 60

5393776-BIM-B-0817
Johnson Controls Unitary Products 11
FIGURE 15: EB/EU12* Wiring Diagram
IF ANY OF THE ORIGINAL WIRE
SUPPLIED WITH THIS UNIT MUST BE
REPLACED. IT MUST BE REPLACED
WITH TYPE 105 C THERMOPLASTIC
WIRING MUST CONFORM TO LOCAL CODES
BLK
RED
WHT
GRN
BLEND AIR
CONTROL BOX
BLU-MED. HIGH SP.
MOTOR
YEL-MED. LOW SP.
BLK-COOLING SP.
RED-HEATING SP.
2 SPADE (INSUL.)
TERMINALS USED
WHEN
CHANGING
SPEEDS LINE
LOAD
ORG
BRN
CAPACITOR
ORG-COMMON.
TRANSFORMER
BLK
3A
FUSE
RED
RED
BLK
G
W
RH
Y
HEAT/COOL
T'STAT
BLOWER
RELAY
2
4
6
5
1
3
RED
BLK
M3 M1
M2
H2
SEQUENCER
BLU
RED
R
R
ELEMENTS SWITCHES
LIMIT
60 AMP
CIRCUIT #1
BREAKER
60 AMP
CIRCUIT #2
BREAKER
BLK
ORG
YEL
ORG
MODEL: EB12F / EU12A
COND. UNIT
CONTACTOR
REPLACE
FILTER
WITH SAME
SIZE
240 VAC - 60 Hz - 1 PHASE
NOTE:
4-SPEED BLOWER
EB / EU SERIES FURNACES
GRN
WHT
M4
H1
YEL
L
L
YEL
YEL
SINGLE BRANCH
CIRCUIT SERVICE
240 VAC.
60Hz
1 PHASE
GND. LUG
THIS FURNACE MAY BE CONNECTED TO MORE THAN ONE POWER SUPPLY.
TURN OFF ALL POWER TO THE FURNACE AT THE WALL BOX, AND LOCK IT OUT.
DO NOT OPEN THIS PANEL UNTIL ELECTRICAL POWER IS SHUT
OFF AT HOUSEHOLD SERVICE BOX. CHECK WITH A VOLTMETER
OR OTHER PROPER INSTRUMENT.
-HAZARD OF ELECTRICAL SHOCK-
SERVICE CONNECTION COVER MUST BE INSTALLED.
IF FILTERS ARE USED, CLEAN/REPLACE EACH SEASON OR
MORE OFTEN IF NEEDED.
CAUTION
5166512-UWD-B-0617
IMPORTANT -
HIGH VOLTAGE
SHOCK HAZARD
WARNING
6
2
48
1
0
RELAY
BRN
BRN
BLK
ORG
D.O.E. OUTPUT CAPACITY - BTU 39,000
MAX. MOTOR-FLA 4.0
SINGLE BRANCH
CIRCUIT SERVICE
2 LEADS +
1 GROUND
NOMINAL CIRCUIT LOAD-AMPS 50.7
WIRE SIZE (75 C) COPPER #6
WIRE SIZE (60 C) COPPER #4
MAX. FUSE SIZE (OR CB) - AMPS 70

5393776-BIM-B-0817
12 Johnson Controls Unitary Products
FIGURE 16: EB/EU15* Wiring Diagram
BLK
RED
WHT
GRN
BLEND AIR
CONTROL BOX
BLU-MED. HIGH SP.
MOTOR
RE-HEATING SP.
BLK-COOLING SP.
YEL-MED SP.
2 SPADE (INSUL.)
TERMINALS USED
WHEN
CHANGING
SPEEDS LINE
LOAD
ORG
BRN
CAPACITOR
ORG-COMMON.
TRANSFORMER
BLK
3A
FUSE
RED
RED
BLK
G
W
RH
Y
HEAT/COOL
T'STAT
BLOWER
RELAY
2
4
6
5
1
3
BLK
M3 M1
M2
H2
M5
M6
H4
H3
WHT
BLK
SEQUENCER
BLU
60 AMP
CIRCUIT 1
240 VAC.
60Hz
1 PHASE
CIRCUIT #1
BREAKER
GND. LUG
60 AMP
CIRCUIT 2
240 VAC.
60Hz
1 PHASE
CIRCUIT #2
BREAKER
DUAL BRANCH
CIRCUIT SERVICE
YEL
YEL
60 AMP
CIRCUIT #1
BREAKER
60 AMP
240 VAC.
60Hz
1 PHASE
CIRCUIT #2
BREAKER GND. LUG
SINGLE BRANCH
CIRCUIT SERVICE
GND. LUG
MODEL:
EB15F / EU15A
COND. UNIT
CONTACTOR
240 VAC - 60 Hz - 1 PHASE
REQUIRES JUMPER BARS (P/N S1-3500-378P)
4-SPEED BLOWER
EB / EU SERIES FURNACES
GRN
WHT
M4
H1
RED
SHOCK HAZARD
THIS FURNACE MAY BE CONNECTED TO MORE THAN ONE POWER SUPPLY.
TURN OFF ALL POWER TO THE FURNACE AT THE WALL BOX, AND LOCK IT OUT.
DO NOT OPEN THIS PANEL UNTIL ELECTRICAL POWER IS SHUT
OFF AT HOUSEHOLD SERVICE BOX. CHECK WITH A VOLTMETER
OR OTHER PROPER INSTRUMENT.
-HAZARD OF ELECTRICAL SHOCK-
SERVICE CONNECTION COVER MUST BE INSTALLED.
IF FILTERS ARE USED, CLEAN/REPLACE EACH SEASON.
OR MORE OFTEN IF NEEDED.
CAUTION
IMPORTANT -
HIGH VOLTAGE
WARNING
IF ANY OF THE ORIGINAL WIRE
SUPPLIED WITH THIS UNIT MUST BE
REPLACED. IT MUST BE REPLACED
WITH TYPE 105 C THERMOPLASTIC
WIRING MUST CONFORM TO LOCAL CODES
R
R
R
L
L
L
ELEMENTS LIMIT
SWITCHES
NOTE:
RED
YEL
YEL
ORG
ORG
BLK
REPLACE
FILTER
WITH SAME
SIZE
WHT
BLK
ORG
ORG
BLK
5166513-UWD-B-0617
6
2
48
1
0
RELAY
6
2
48
1
0
RELAY
BRN
BLK
BLK
ORG
YEL
ORG
D.O.E. OUTPUT CAPACITY - BTU 51,000
MAX. MOTOR-FLA 4.0
SINGLE BRANCH
CIRCUIT SERVICE
2 LEADS +
1 GROUND
NOMINAL CIRCUIT LOAD-AMPS 64.0
WIRE SIZE (75 C) COPPER #4
WIRE SIZE (60 C) COPPER #3
MAX. FUSE SIZE
(OR CB) - AMPS 80
DUAL BRANCH
CIRCUIT SERVICE
4 LEADS +
2 GROUNDS
CKT #1-CKT #2
BRANCH CKT. LOAD-AMPS 44 20.1
BRANCH CKT. MIN. AMPACITY 55 25.2
WIRE SIZE (75 C) COPPER #6 #10
WIRE SIZE (60 C) COPPER #6 #10
MAX. FUSE SIZE
(OR CB) - AMPS
60 30

5393776-BIM-B-0817
Johnson Controls Unitary Products 13
FIGURE 17: EB/EU17* Wiring Diagram
BLK
RED
WHT
GRN
BLEND AIR
CONTROL BOX
BLU-MED. HIGH SP.
MOTOR
RE-HEATING SP.
BLK-COOLING SP.
YEL-MED SP.
2 SPADE (INSUL.)
TERMINALS USED
WHEN
CHANGING
SPEEDS LINE
LOAD
ORG
BRN
CAPACITOR
ORG-COMMON.
TRANSFORMER
BLK
3A
FUSE
RED
RED
BLK
G
W
RH
Y
HEAT/COOL
T'STAT
BLOWER
RELAY
2
4
6
5
1
3
RED
BLK
M3 M1
M2
H2
M5
M6
H4
H3
WHT
BLK
SEQUENCER
BLU
60 AMP
CIRCUIT 1
240 VAC.
60Hz
1 PHASE
CIRCUIT #1
BREAKER
GND. LUG
60 AMP
CIRCUIT 2
240 VAC.
60Hz
1 PHASE
CIRCUIT #2
BREAKER
DUAL BRANCH
CIRCUIT SERVICE
YEL
YEL
60 AMP
CIRCUIT #1
BREAKER
60 AMP
240 VAC.
60Hz
1 PHASE
CIRCUIT #2
BREAKER GND. LUG
SINGLE BRANCH
CIRCUIT SERVICE
GND. LUG
MODEL:
EB17F / EU17A
COND. UNIT
CONTACTOR
240 VAC - 60 Hz - 1 PHASE
REQUIRES JUMPER BARS (P/N S1-3500-378P)
4-SPEED BLOWER
EB / EU SERIES FURNACES
GRN
WHT
M4
H1
RED
SHOCK HAZARD
THIS FURNACE MAY BE CONNECTED TO MORE THAN ONE POWER SUPPLY.
TURN OFF ALL POWER TO THE FURNACE AT THE WALL BOX, AND LOCK IT OUT.
DO NOT OPEN THIS PANEL UNTIL ELECTRICAL POWER IS SHUT
OFF AT HOUSEHOLD SERVICE BOX. CHECK WITH A VOLTMETER
OR OTHER PROPER INSTRUMENT.
-HAZARD OF ELECTRICAL SHOCK-
SERVICE CONNECTION COVER MUST BE INSTALLED.
IF FILTERS ARE USED, CLEAN/REPLACE EACH SEASON
OR MORE OFTEN IF NEEDED.
CAUTION
IMPORTANT -
HIGH VOLTAGE
WARNING
IF ANY OF THE ORIGINAL WIRE
SUPPLIED WITH THIS UNIT MUST BE
REPLACED. IT MUST BE REPLACED
WITH TYPE 105 C THERMOPLASTIC
WIRING MUST CONFORM TO LOCAL CODES
R
R
R
L
L
L
ELEMENTS LIMIT
SWITCHES
NOTE:
RED
YEL
YEL
ORG
ORG
BLK
REPLACE
FILTER
WITH SAME
SIZE
WHT
BLK
ORG
ORG
BLK
5166514-UWD-B-0617
6
2
48
1
0
RELAY
6
2
48
1
0
RELAY
BRN
BLK
BLK
ORG
YEL
ORG
D.O.E. OUTPUT CAPACITY - BTU 56,000
MAX. MOTOR-FLA 4.0
SINGLE BRANCH
CIRCUIT SERVICE
2 LEADS +
1 GROUND
NOMINAL CIRCUIT LOAD-AMPS 70.7
WIRE SIZE (75 C) COPPER #3
WIRE SIZE (60 C) COPPER #2
MAX. FUSE SIZE
(OR CB) - AMPS 90
DUAL BRANCH
CIRCUIT SERVICE
4 LEADS +
2 GROUNDS
CKT #1-CKT #2
BRANCH CKT. LOAD-AMPS 47.3 23.4
BRANCH CKT. MIN. AMPACITY 59.2 29.3
WIRE SIZE (75 C) COPPER #6 #10
WIRE SIZE (60 C) COPPER #4 #10
MAX. FUSE SIZE
(OR CB) - AMPS
60 30

5393776-BIM-B-0817
14 Johnson Controls Unitary Products
FIGURE 18: EB/EU20* Wiring Diagram
BLK
RED
WHT
GRN
BLEND AIR
CONTROL BOX
BLU-MED. HIGH SP.
MOTOR
RE-HEATING SP.
BLK-COOLING SP.
YEL-MED SP.
2 SPADE (INSUL.)
TERMINALS USED
WHEN
CHANGING
SPEEDS LINE
LOAD
ORG
BRN
CAPACITOR
ORG-COMMON.
TRANSFORMER
BLK
3A
FUSE
RED
RED
BLK
G
W
RH
Y
HEAT/COOL
T'STAT
BLOWER
RELAY
2
4
6
5
1
3
RED
BLK
M3 M1
M2
H2
M5
M6
H4
H3
WHT
BLK
SEQUENCER
BLU
60 AMP
CIRCUIT 1
240 VAC.
60Hz
1 PHASE
CIRCUIT #1
BREAKER
GND. LUG
60 AMP
CIRCUIT 2
240 VAC.
60Hz
1 PHASE
CIRCUIT #2
BREAKER
DUAL BRANCH
CIRCUIT SERVICE
YEL
YEL
60 AMP
CIRCUIT #1
BREAKER
60 AMP
240 VAC.
60Hz
1 PHASE
CIRCUIT #2
BREAKER GND. LUG
SINGLE BRANCH
CIRCUIT SERVICE
GND. LUG
MODEL:
EB20F / EU20A
COND. UNIT
CONTACTOR
240 VAC - 60 Hz - 1 PHASE
REQUIRES JUMPER BARS (P/N S1-3500-378P)
4-SPEED BLOWER
EB / EU SERIES FURNACES
GRN
WHT
M4
H1
M7
M8
RED
SHOCK HAZARD
THIS FURNACE MAY BE CONNECTED TO MORE THAN ONE POWER SUPPLY.
TURN OFF ALL POWER TO THE FURNACE AT THE WALL BOX, AND LOCK IT OUT.
DO NOT OPEN THIS PANEL UNTIL ELECTRICAL POWER IS SHUT
OFF AT HOUSEHOLD SERVICE BOX. CHECK WITH A VOLTMETER
OR OTHER PROPER INSTRUMENT.
-HAZARD OF ELECTRICAL SHOCK-
SERVICE CONNECTION COVER MUST BE INSTALLED.
IF FILTERS ARE USED, CLEAN/REPLACE EACH SEASON
OR MORE OFTEN IF NEEDED.
CAUTION
IMPORTANT -
HIGH VOLTAGE
WARNING
IF ANY OF THE ORIGINAL WIRE
SUPPLIED WITH THIS UNIT MUST BE
REPLACED. IT MUST BE REPLACED
WITH TYPE 105 C THERMOPLASTIC
WIRING MUST CONFORM TO LOCAL CODES
R
R
R
L
L
L
ELEMENTS LIMIT
SWITCHES
NOTE:
R
L
RED
RED
YEL
YEL
ORG
ORG
BLK
BLK
REPLACE
FILTER
WITH SAME
SIZE
WHT
BLK
ORG
ORG
BLK
5166515-UWD-B-0617
6
2
48
1
0
RELAY
6
2
48
1
0
RELAY
BRN
BLK
BLK
ORG
YEL
ORG
D.O.E. OUTPUT CAPACITY - BTU 67,000
MAX. MOTOR-FLA 4.0
SINGLE BRANCH
CIRCUIT SERVICE
2 LEADS +
1 GROUND
NOMINAL CIRCUIT LOAD-AMPS 84.0
WIRE SIZE (75 C) COPPER #2
WIRE SIZE (60 C) COPPER #1
MAX. FUSE SIZE
(OR CB) - AMPS 110
DUAL BRANCH
CIRCUIT SERVICE
4 LEADS +
2 GROUNDS
CKT #1-CKT #2
BRANCH CKT. LOAD-AMPS 44 40
BRANCH CKT. MIN. AMPACITY 55 50
WIRE SIZE (75 C) COPPER #6 #8
WIRE SIZE (60 C) COPPER #6 #6
MAX. FUSE SIZE
(OR CB) - AMPS
60 50

5393776-BIM-B-0817
Johnson Controls Unitary Products 15
FIGURE 19: EB/EU23* Wiring Diagram
IF ANY OF THE ORIGINAL WIRE
SUPPLIED WITH THIS UNIT MUST BE
REPLACED. IT MUST BE REPLACED
WITH TYPE 105 C THERMOPLASTIC
WIRING MUST CONFORM TO LOCAL CODES
BLK
RED
WHT
GRN
BLEND AIR
CONTROL BOX
BLU-MED. HIGH SP.
MOTOR
RE-HEATING SP.
BLK-COOLING SP.
YEL-MED SP.
2 SPADE (INSUL.)
TERMINALS USED
WHEN
CHANGING
SPEEDS LINE
LOAD
ORG
BRN
CAPACITOR
ORG-COMMON.
TRANSFORMER
BLK
3A
FUSE
RED
RED
BLK
G
W
RH
Y
HEAT/COOL
T'STAT
BLOWER
RELAY
2
4
6
5
1
3
RED
BLK
M3 M1
M2
H2
M5
M6
H4
H3
WHT
BLK
SEQUENCER
BLU
YEL
R
R
R
L
L
L
ELEMENTS LIMIT
SWITCHES
60 AMP
CIRCUIT 1
240 VAC.
60Hz
1 PHASE
CIRCUIT #1
BREAKER
GND. LUG
DUAL BRANCH
CIRCUIT SERVICE
YEL
YEL
ORG
60 AMP
CIRCUIT #1
BREAKER
60 AMP
240 VAC.
60Hz
1 PHASE
CIRCUIT #2
BREAKER GND. LUG
SINGLE BRANCH
CIRCUIT SERVICE
MODEL:
EB23F / EU23A
COND. UNIT
CONTACTOR
REPLACE
FILTER
WITH SAME
SIZE
240 VAC - 60 Hz - 1 PHASE
REQUIRES JUMPER BARS (P/N S1-3500-378P)
NOTE:
4-SPEED BLOWER
EB / EU SERIES FURNACES
GRN
WHT
M4
H1
M7
M8
RED
R
L
SHOCK HAZARD
THIS FURNACE MAY BE CONNECTED TO MORE THAN ONE POWER SUPPLY.
TURN OFF ALL POWER TO THE FURNACE AT THE WALL BOX, AND LOCK IT OUT.
DO NOT OPEN THIS PANEL UNTIL ELECTRICAL POWER IS SHUT
OFF AT HOUSEHOLD SERVICE BOX. CHECK WITH A VOLTMETER
OR OTHER PROPER INSTRUMENT.
-HAZARD OF ELECTRICAL SHOCK-
SERVICE CONNECTION COVER MUST BE INSTALLED.
IF FILTERS ARE USED, CLEAN/REPLACE EACH SEASON
OR MORE OFTEN IF NEEDED.
CAUTION
IMPORTANT -
HIGH VOLTAGE
WARNING
YEL
WHT
RED
RED
YEL
YEL
BLK
5166516-UWD-B-0617
60 AMP
CIRCUIT 2
240 VAC.
60Hz
1 PHASE
CIRCUIT #2
BREAKER GND. LUG
ORG
ORG
BLK
BLK
ORG
ORG
BLK
6
2
48
1
0
RELAY
6
2
48
1
0
RELAY
BRN
BLK
BLK
ORG
D.O.E. OUTPUT CAPACITY - BTU 77,000
MAX. MOTOR-FLA 4.0
SINGLE BRANCH
CIRCUIT SERVICE
2 LEADS +
1 GROUND
NOMINAL CIRCUIT LOAD-AMPS 94.0
WIRE SIZE (75 C) COPPER #1
WIRE SIZE (60 C) COPPER #0
MAX. FUSE SIZE
(OR CB) - AMPS 120
DUAL BRANCH
CIRCUIT SERVICE
4 LEADS +
2 GROUNDS
CKT #1-CKT #2
BRANCH CKT. LOAD-AMPS 47.3 46.7
BRANCH CKT. MIN. AMPACITY 59.2 58.4
WIRE SIZE (75 C) COPPER #6 #6
WIRE SIZE (60 C) COPPER #4 #4
MAX. FUSE SIZE
(OR CB) - AMPS
60 60

Subject to change without notice. Published in U.S.A. 5393776-BIM-B-0817
Copyright © 2017 by Johnson Controls, Inc. All rights reserved. Supersedes: 5393776-BIM-A-0717
York International Corp.
5005 York Drive
Norman, OK 73069
NOTES