Keyprocessor Sirius i80 User manual

Card reader Sirius i80(P)
Installation manual
oProduct
oInstallation
oConnection
oTechnical data

Publication
January 2014,
Keyprocessor BV
Paasheuvelweg 20
1105BJ Amsterdam, The Netherlands
www.keyprocessor.com
Tel.: [phone]
This manual represents the knowledge at the above mentioned time. Keyprocessor works non-
stop to improve her products. For the most recent technical information please contact your
consultant or dealer.
Content overview
Publication.................................................................................................................... 2
Content overview .......................................................................................................... 2
1The product .................................................................................................... 3
1.1 Sticker i-serie ............................................................................................. 3
1.2 Spacers...................................................................................................... 3
1.3 Default reader configurations ........................................................................ 4
1.3.1 Polyx/Orbit Mifare- MifareDesfire ................................................................... 4
1.3.2 Chip Serie nummer (CSN) ............................................................................ 5
1.3.3 Sirius i-80 programmable using configuration cards ......................................... 5
1.3.4 Sirius i-80 programmable using PS application and configuration cards .............. 5
2Installation and use ......................................................................................... 6
2.1 Location ..................................................................................................... 6
2.2 Mounting instructions................................................................................... 6
2.3 Use of the i80/P .......................................................................................... 7
3Connection ..................................................................................................... 8
3.1 Sirius i80 connector lay-out .......................................................................... 8
3.2 If door controller Polyx™ .............................................................................. 8
3.2.1 Direct connection (RS485)............................................................................ 9
3.2.2 Connection using an Adapterboard ...............................................................10
3.3 If door controller Orbit ................................................................................11
3.3.1 Connecting with UTP cable...........................................................................11
3.3.2 Connection with CKY 3x2x0,14mm²..............................................................11
4Technical data................................................................................................12
4.1 Cable specifications ....................................................................................13
4.1.1 Data signal Clock/Data................................................................................13
4.1.2 Data signal Wiegand ...................................................................................13
4.1.3 Data signal RS485 ......................................................................................14
4.2 Certificates ................................................................................................15

1The product
The Sirius i-series card reader is a versatile card reader which supports multiple card
technologies and communication protocols. In addition, this card reader is able to support
different technologies simultaneously like Mifare classic and DESFire EV1.
The card reader is equipped with a function to automatically adjust the antenna on and off
when no activity takes place around the card reader. The detection is based on proximity.
The purpose of this functionality is to create a card reader as energy efficient as possible and
only activate the antenna when a person or card is detected near to the card reader.
This manual provides the necessary information concerning the installation instructions,
mounting and use of the card reader which is supplied as standard.
The Sirius i-series card reader:
Sirius i80 Sirius i80/P
1.1 Sticker i-serie
On the back of the card reader a sticker placed.
This sticker features a QR code.
After scanning this QR code, all necessary information
will be downloaded automatically.
1.2 Spacers
The spacer is designed for the following purpose. It can make the card reader more robust for
external influences but it can also be useful when installing the Sirius card reader on existing
plants.
801-6120 Sirius i80(p) Spacer
801-6121 Outside mounting spacer

1.3 Default reader configurations
When using a default Sirius i-series card reader, four configurations are possible
The configurations are described in the paragraphs below.
Remark: For more information about the additional options, please contact your contact at
Keyprocessor.
Remark: The Sirius-i80/P (Pincode) card reader will only work in combination with a Polyx
door controller.
1.3.1 Polyx/Orbit Mifare- MifareDesfire
Part number: 801-5101
Standard communication:
A Polyx based on RS485
An Orbit based on Clock/Data - MIFARE Classic & MIFARE DESFire EV1(coded)
Output length when using Clock/Data:
When using Mifare Classic, the output length is 8 digits
When using Mifare DESFire, the output length is 12 digits
Standard LED function:
When the reader is provided with power, the LED color is Red.
When the LED connection is switched to GND, the LED color is Green
Standard IO function:
When using Mifare Classic, the output length is 8 digits
A standard configured card reader does not use the extra IO functionality. When this
function is needed, you need to order another card reader. See chapter 1.3.3 & 1.3.4
Programmable:
The card reader is not programmable.

1.3.2 Chip Serie nummer (CSN)
Part number:
I80 801-5112
I80p 801-5122
Default Card reader protocol:
An Orbit based on Clock/Data.
Output length based on Clock/Data:
The length of the Chip Serial Number (CSN) is 4 byte swapped (10 digits decimal)
Attention! When using a 7 byte (random) CSN, the card reader must communicate with a
Polyx™. In this case you need to order another card reader. See chapter 1.2.3 &
1.2.4
Standard LED function:
When the reader is provided with power, the LED color is Red.
When the LED connection is switched to GND, the LED color is Green
Standard IO function:
A standard configured card reader does not use the extra IO functionality. When this
function is needed, you need to order another card reader. See chapter 1.2.3 & 1.2.4
Programmable:
The card reader is not programmable.
1.3.3 Sirius i-80 programmable using configuration
cards
Part number: 801-5113
After connecting the Power to the card reader, the LED turns blue / purple. A
configuration card is needed to turn the reader in operational mode.
You can order a configuration card via Keyprocessor. To create 'custom' configuration
cards extra costs will be calculated.
1.3.4 Sirius i-80 programmable using PS application
and configuration cards
Part number: 501-5114
After connecting the Power to the card reader, the LED turns blue / purple. A
configuration card is needed to turn the reader in operational mode.
The card reader is fully programmable using a PC application and you’re able to create
your own configuration cards.

2Installation and use
By the use of ferrite, the card reader is insensitive to be installed on a metal surface.
2.1 Location
Determine the location where the Sirius card reader should be installed. There is a
maximum cable length between the reader and door controller.
Exception: using an external power supply, you can increase the achievable distance
between the door controller and card reader.
Install the reader with a minimum lateral distance of 20 cm from each other.
2.2 Mounting instructions
Mount the card reader preferably on an outlet
Picture 1: Sirius i80 measurements
Pull the cable through the mounting plate of the Sirius reader.
The screw hole of the card reader should be placed on the underside.
Mount the back plate of the card reader to the outlet, using the existing screws.
When not removed, remove the orange colored film of the Buzzer
Click the front of the card reader at the top of the mounting plate
Attach the front of the card reader to the mounting plate with the supplied 'special
mounting bolts.

2.3 Use of the i80/P
When entering the PIN code, the finger must be released at least 1 cm from the panel before
the next digit is entered.

3Connection
Remark! Depending on the configuration of the card reader, the inputs and outputs of the
card reader can be used.
3.1 Sirius i80 connector lay-out
Connect the cable as shown in this chapter
The reader accepts a supply voltage of 5.0 - 16.0 VDC.
A higher input voltage results in a lower power consumption and provide cost-effective wiring
with a smaller diameter of the conductor.
When using an external power supply, it must comply with the SELV guidelines.
3.2 If door controller Polyx™
The Sirius card reader can be connected in two ways with the Polyx ™: directly or by using an
Adapterboard
For optimal communication, it is recommended to have the latest version of one of the
following operating system
2.6 JFSS2
3.3 UbiFS
Pin number
Clock/Data
Wiegand
RS485
7
Vcc (+)
Vcc (+)
Vcc (+)
6
GND (-)
GND (-)
GND (-)
5
Ext. Input 1(LED)
Ext. Input 1(LED)
Ext. Input 1
4
Clock
D1
Ext. Output 2
3
Data
D0
Ext. Output 1
2
Ext. Input 2
Ext. Input 2
B
1
Ext. Output 1
Ext. Output 1
A

Remark! Browse to the polyx to see the version information. For more information about
the versions, see the KP_Install_update_Polyx manual.
3.2.1 Direct connection (RS485)
Recommended cable type between a Polyx and the Sirius card reader is: (see chapter 4.1 for
more information)
CAT5 UTP four twisted pairs of 24AWG copper conductors
CAT6 UTP four twisted pairs of 24AWG copper conductors
A direct connection (without using an Adapterboard) between the Sirius card reader and a
Polyx™ is NOT possible when:
Sirius and Polyx™ are installed in different buildings and thus the connection
leaves the building or
the wiring is no UTP cable (CAT5 or CAT6) or
an existing (non UTP) cable is reused or
overvoltage protection for the card reader is required or
An external power supply is required for the card reader.
If any of the above conditions applies, see section 3.2.2.
Polyx, directly connected to a Sirius card reader:
Picture T-568B
Pin number RJ-
45 Plug
Polyx™ PRT 2/3
TIA/EIA-568-B
Cable color
Signal
Connection
Sirius i30 card
reader
1
White/orange
B
2
2
Orange
A
1
3
White/green
B
2
4
Blue
Vcc (+)
7
5
White/blue
6
Green
A
1
7
White/brown
8
Brown
GND (-)
6

3.2.2 Connection using an Adapterboard
Recommended cable type between a Polyx and the Sirius card reader, using an Adapterboard
is:
Shielded cable with twisted pairs
If a direct connection is not possible, an Adapterboard must be placed between Polyx and the
Sirius card reader.
Adapterboard and Polyx are connected with a default UTP cat5 cable (or higher) (plug
connection).
Connecting wires as shown in the diagrams below.
Or screw connection
on Adapterboard
Or RJ45
connection
on
Adapterboard
TIA/EIA-568-B
Cable color
Signal
Connection
Sirius i80 Sirius
i80(/P) card
reader
A (or 1)
1
White/orange
B
2
B (or 2)
2
Orange
A
1
Y (or 3)
3
White/green
B
2
“+”
4
Blue
Vcc (+)
7
5
White/blue
Z (or 6)
6
Green
A
1
7
White/brown
“—”
8
Brown
GND (-)
6
Connect GND of the Adapterboard to the local Earth.
Connect the shield of the ground cable to the GND connection of the Adapterboard.
Do not place any jumpers! For more information see the Adapterboard manual.
Possible connections of the card reader Sirius on the Adapterboard

3.3 If door controller Orbit
Recommended cable type between the Orbit and Sirius card reader:
CKY 3x2x0,14mm²
CKY 4x2x0,14mm²
CAT5 UTP four twisted pairs of 24AWG copper conductors
CAT6 UTP four twisted pairs of 24AWG copper conductors
3.3.1 Connecting with UTP cable
TIA/EIA-568-B
Cable color
Connection
on the Orbit
Connection
Sirius i80 card reader
White/orange
Data/D0
3
Orange
-
-
White/green
Clock/D1
4
Blue
+5V
7
White/blue
LED
5
Green
-
-
White/brown
GND
6
Brown
GND
6
3.3.2 Connection with CKY 3x2x0,14mm²
Cable color
Connection
on the Orbit
Connection
Sirius i80 card reader
Green
Data/D0
3
Yellow
Clock/D1
4
Pink
+5V
7
Grey
LED
5
White
GND
6
Brown
GND
6

4Technical data
Model
Sirius i80 card reader
Interface
Sirius Clock/Data, Wiegand
Sirius - Polyx™ (RS485)
Data type
Read
Read/write
Readable cards
Mifare 1K, Mifare 4K, Mifare
DESFire 0.6, Mifare DESFire EV1
8K and ISO14443A compatible
card
Mifare 1K, Mifare 4K, Mifare
DESFire 0.6, Mifare DESFire
EV1 8K, Rijkspas and
ISO14443A compatible card
Power supply
5-16V DC Average: 0,7W
Peak: 1,4W
5-16V DC Average: 0,7W
Peak: 1,4W
Led consumption, both on
100%
On 12V, max. 1,8W
LED input
LED input with pull-up, active low
Ext. output
max. Voltage 45V; Open collector output; sinked current. Max.
current 500mA
Ext. input 1
Resistance 1kOhm
Dimensions (mm) i80
80x80x19
Reading Distance i80
5mm-70mm for ISO14443A Mifare card; (depending on
environment and transponder)
Environmental Rating i80
IP64
Operating Temperature
-31º to 150º F (-35º to 65º C)
Storage Temperature
-67º to 185º F (-55º to 85º C)
Operating Humidity
5% to 95% relative humidity non-condensing
Transmit Frequency
13.56 MHz
Standard
ISO14443 A
Indicators
2x RGB LED and 1 buzzer
Connection
7-pin screw connector
Certifications
CE

4.1 Cable specifications
Cable specifications (non-shielded)
4.1.1 Data signal Clock/Data
4.1.2 Data signal Wiegand
Interface
Maximum cable length
min.conductor size with
12 VDC supply
1 = 5V DC
Meters
Feet
mm2
AWG
Wiegand
40
130
0.14
26
80
260
0.25
24
120
390
0.34
22
Clock/Data
201
661
0.14
26
0.25
24
0.34
22
RS485 (cable
power)
120
200
0.25
24
150
490
0.34
22
RS485 (external
power)
600
1965
0.25
24

4.1.3 Data signal RS485

4.2 Certificates